Hitachi J300U Series instruction manual Screen display

(2)Extension function mode

•Each function name and settable range to the extension function mode are shown below.

•Set the extension function code to be changed by .

Display				Screen display		Settable		Set
	Externsion function name					for	Remarks
order		Code	Settable	Setting range	Initial value	2nd		value
		display	during			function
			running
1	Control method setting	A 0	Ñ	0-5	0	√
2	Motor capacity setting	A 1	Ñ	3.7 to 160		√	NOTE 1
3	Motor poles setting	A 2	Ñ	2/4/6/8	4	√
4	Speed control response constant setting	A 3	Ñ	0.00-9.99/10.0-99.9/100	2.00	√
5	Start frequency adjustment	A 4	Ñ	0.10-9.99	0.50	Ñ
6	Maximum frequency limiter setting	A 5	Ñ	0-120 (400)	0	Ñ
7	Minimum frequency limiter setting	A 6	Ñ	0-120 (400)	0	Ñ
8	Jump frequency setting 1	A 7	Ñ	0-400	0	Ñ
9	Jump frequency setting 2	A 8	Ñ	0-400	0	Ñ
10	Jump frequency setting 3	A 9	Ñ	0-400	0	Ñ
11	Carrier frequency setting	A10	Ñ	2.0-16.0	(16.0)	Ñ	See 7-18
12	Frequency command sampling frequency	A11	Ñ	1-8	8	Ñ
13	Multispeed first speed setting	A12	Ñ	0-120 (400)	0	Ñ
14	Multispeed second speed setting	A13	Ñ	0-120 (400)	0	Ñ
15	Multispeed third speed setting	A14	Ñ	0-120 (400)	0	Ñ
16	Electronic thermal level adjustment	A23	Ñ	20-120	100	√
17	Electronic thermal characteristic selection	A24	Ñ	0-2	1	√
18	Motor pole number setting for motor speed monitor	A25	Ñ	2 to 48	4	Ñ
19	External frequency setting start	A26	Ñ	0-120 (400)	0	Ñ
20	External frequency setting end	A27	Ñ	0-120 (400)	0	Ñ
21	Instantaneous restart selection	A34	Ñ	0-3	0	Ñ
22	Dynamic braking usage ratio	A38	Ñ	0.0-99.9/100	(1.5)	Ñ	See 7-21
23	Optional arrival frequency for acceleration	A39	Ñ	0-400	0	Ñ
24	Optional arrival frequency for deceleration	A40	Ñ	0-400	0	Ñ
25	Monitor signal selection	A44	Ñ	0-3	0	Ñ
26	Frequency converted value setting	A47	Ñ	0.0-99.9	1.0	Ñ
27	Analog input selection	A48	Ñ	0-1	1	Ñ
28	Frequency arrival signal output method	A49	Ñ	0-2	0	Ñ
29	Restarting after FRS signal selection	A54	Ñ	0-1	1	Ñ
30	Reduced voltage soft start setting	A58	Ñ	0-6	6	Ñ
31	Running mode selection	A59	Ñ	0-2	0	Ñ
32	Jogging freguency setting	A61	Ñ	0-9.99	1.00	Ñ	Frequencies below
							the start frequency
							cannot be set.
33	Base frequency setting	A62	Ñ	30-120 (400)	60	√
34	Maximum frequency setting	A63	Ñ	30-120 (400)	60	√
35	Maximum frequency selection	A64	Ñ	120/400	120	Ñ
36	Frequency command/output frequency adjust (O-L terminal)	A80	Ñ	0-255	Ñ	Ñ	NOTE 2
37	Frequency command/output frequency adjust (OI-L terminal)	A81	Ñ	0-255	Ñ	Ñ	NOTE 2
38	Selection of reset terminal performance	A86	Ñ	0, 1	0	Ñ
39	P gain setting of PID funciton	A90	Ñ	0.1-0.5	1.0	Ñ
40	I gain setting of PID funciton	A91	Ñ	0.0-15.0	1.0	Ñ
41	D gain settingof PID function	A92	Ñ	0.0-100	0.0	Ñ
42	Selection of PID funciton	A94	Ñ	0-4	0	Ñ
43	Setting method of PID reference value	A95	Ñ	0, 1	0	Ñ
44	Setting of PID reference value	A96	Ñ	0.00-200	0.00	Ñ
45	Auto tuning setitng	A97	Ñ	0-2	0	Ñ
46	Motor data selection	A98	Ñ	0-2	0	√
47	Ro-To option selection	A99	Ñ	0-1	0	Ñ
48	Input terminal setting 1	C 0	Ñ	0-3, 5-9, 11-16, 18-28	18	Ñ
49	Input terminal setting 2	C 1	Ñ	0-3, 5-9, 11-16, 18-28	16	Ñ
50	Input terminal setting 3	C 2	Ñ	0-3, 5-9, 11-16, 18-28	5	Ñ
51	Input terminal setting 4	C 3	Ñ	0-3, 5-9, 11-16, 18-28	11	Ñ
52	Input terminal setting 5	C 4	Ñ	0-3, 5-9, 11-16, 18-28	9	Ñ
53	Input terminal setting 6	C 5	Ñ	0-3, 5-9, 11-16, 18-28	13	Ñ
54	Input terminal setting 7	C 6	Ñ	0-3, 5-9, 11-16, 18-28	1	Ñ
55	Input terminal setting 8	C 7	Ñ	0-3, 5-9, 11-16, 18-28	0	Ñ
56	Output terminal setting 11	C10	Ñ	0-2	0	Ñ
57	Output terminal setting 12	C11	Ñ	0-2	1	Ñ
58	Input terminal a and b contact setting	C20	Ñ	00-FF	00	Ñ
59	Output terminal a and b contact setting	C21	Ñ	00-07	04	Ñ

NOTE 1: The most applicable motor capacity of the inverter is set.

NOTE 2: The initial setting of each inverter is adjusted when shipping from the works.

7-6