Mitsubishi Electronics manual 142

11 TROUBLESHOOTING

MELSEC-Q

	Error Code		Error Contents and Cause	Corrective Action	Corres-
					ponding
	(SD0)	1
					CPU
				Read the individual information of the error, check the program	QCPU
			Station not loaded was specified using the instruction whose target		function
				corresponding that value (program error location), and make
			was the PLC share memory.		Ver. B
				correction.
2110					or later
			(1) The location designated by the FROM/TO instruction set is not a	(1) Read error individual information, then check and edit the
			special function module.	FROM/TO instruction set that corresponds to the numerical
			(2) The special function module, Network module being accessed is	value there (Program error location).
			faulty.	(2) The special function module that is being accessed has a
2111			The location designated by a link direct device (J \ ) is not a	hardware error. Consult the nearest service center, agent or our
			network module.	branch office and describe the symptom.

(1)The location designated by a special function module dedicated instruction is not a special function module.

2112	(2) The network number specified by the network dedicated	Read error individual information, then check and edit the special	Rem
	instruction does not exist, or the network module is not the
		function module (Network module) dedicated instruction that
	corresponding one.
		corresponds to the numerical value there (program error location).
	(3) Alternatively, it is not the relevant special function module.
2113	The one specified in the network-dedicated instruction is not a
	network module, or a relay target network does not exist.
2114	An instruction, which on execution specifies other stations, has
	been used for specifying the host station. (An instruction that does
	not allow the host station to be specified).
2115	An instruction, which on execution specifies the host station, has
	been used for specifying other stations. (An instruction that does not	Read the individual information of the error, check the program	QCPU
	allow other stations to be specified).	corresponding that value (program error location), and make	function
	• An instruction that does not allow the module under the control of		Ver. B
		correction.
2116	another station to be specified is being used for a similar task.		or later
	• Instruction was executed for the A or QnA module under control of
	another station.
2117	A CPU module that cannot be specified in the instruction dedicated
	to the multiple CPU system was specified.
2120	The location of Q B and QA1S B is improper.	Check the location of the base unit.
2121	The CPU module is installed at other than the CPU slot or slots 0 to	Check the loading position of the CPU module and reinstall it at the
	2.	correct slot.
2122	QA1S B is used to the main base unit.	Use Q3 B as the main base unit.
	(1) A module is installed at 65th or higher slot.	(1) Remove the module installed at 65th or later slot.
		(2) Remove the module installed at the slot later than the number of
	(2) A module is installed at the slot later than the number of slots		QCPU
		slots specified with base allocation setting.
2124	specified with base allocation setting.	(3) Remove the module installed at the I/O points later than the	Rem
	(3) A module is installed at the I/O points later than the 4,096th
		4,096th point.
	point.
		(4) Change the last module to a module which does not exceed the
	(4) A module installed at the 4,096th point occupies higher points.
		4,096th point.
	(1) A module which the QCPU cannot recognise has been installed.	(1) Install a module which can be used with the CPU.
2125		(2) The intelligent function module is experiencing hardware
	(2) There was no response form the intelligent function module.
		problems. Contact your nearest Mitsubishi representative.
	CPU module locations in a multiple CPU system are either of the	(1) Eliminate empty slots between the CPU modules. (Set empty
	following.	slots on the right side of the CPU modules.)
2126	(1) There are empty slots between the QCPU and QCPU/motion	(2) Remove the modules, which are not the QCPU modules, loaded
	controller.	between the QCPU modules, and fit the slots with the QCPUs.	QCPU
	(2) Modules other than the QCPU (including the motion controller)	Load the motion controller modules on the right side of the	function
	modules are loaded between the QCPU modules.	QCPUs.	Ver. B
	In a multiple CPU system, the control PLC of the intelligent function	(1) Change the intelligent function module for the one compatible	or later
		with the multiple CPU system (function version B).
2150	module incompatible with the multiple CPU system is set to other
		(2) Change the setting of the control CPU of the intelligent function
	than station 1.
		module incompatible with the multiple CPU system to station 1.
	There is no parameter file at the drive designated by DIP switches	Check and correct the setting of the parameter enabled drive
2200		switch.
	as a valid drive.	Put a parameter file in the drive designated by the parameter
		enabled drive switch.
	The contents of the boot file are incorrect.	Check the boot setting.	QCPU
2210	There is no boot file in the drive designated by the parameter	Check and correct the setting of the parameter enabled drive
		switch.	QnA
	enabled drive switch even though the Boot DIP switch is ON.	Put a boot file in the drive designated by the parameter enabled
		drive switch.
	(1) A memory card was removed without switching the memory	(1) Remove memory card after placing the memory card in/out
	card in/out switch OFF.
2300		switch OFF.
	(2) The memory card in/out switch is turned ON although a memory
		(2) Turn on the card insert switch after inserting a memory card.
	card is not actually installed.
2301	(1) The memory card has not been formatted.	(1) Format memory card.
	(2) Memory card format status is incorrect.
		(2) Reformat memory card.
	A memory card that cannot be used with the CPU module has been
2302		Check memory card.
	installed.
	Automatic write to standard ROM was performed on the CPU	(1) Execute automatic write to standard ROM on the CPU module
		which is compatible with automatic write to standard ROM.	QCPU
	module that is incompatible with automatic write to standard ROM.	(2) Using GX Developer, perform write of parameters and programs
			function
	(Memory card where automatic write to standard ROM was	to standard ROM.
			Ver. B
	selected in the boot file was fitted and the parameter enable drive	(3) Change the memory card for the one where automatic write to
			or later
	was set to the memory card.)	standard ROM has not been set, and perform boot operation
2400		from the memory card.
		Read the error individual information at the peripheral device, check
	The file designated at the PLC file settings in the parameters cannot	to be sure that the parameter drive name and file name correspond
		to the numerical values there (parameter number), and correct.
	be found.	Create a file created using parameters, and load it to the CPU
		module.
	The Ethernet parameter that was added for QnACPU, with the	Change to QnACPU with the function version "B." Delete the
	function version "B," has been set to QnACPU without the function		QnA
		Ethernet parameter.
	version "B."

1 Characters in parentheses ( ) indicate the special register numbers where individual information is being stored.

11 - 26 11 - 26