Mitsubishi Electronics Q172DCPU, Q173DCPU 128

4 AUXILIARY AND APPLIED FUNCTIONS

POINT

(1)After completion of SSCNET communication disconnect processing, be sure to check the LED display of the servo amplifier for "AA" before turning OFF its the power supply.

(2)When a "1 to 32 : Disconnect command" and/or "-10 : Connect command" are set to the "Connect/disconnect command device (SD803)", the status of the SD508 changes to the "-1: Connect/disconnect waiting" state. In order to complete connect/disconnect processing, "-2 : Connect/disconnect execute command" must be set to SD803 to execute the prior connect/disconnect command.

(3)When "1 to 32 : Disconnect command" is set to axis not disconnect, the connect/disconnect status device (SD508) returns "0" without entering the status of "-1 : Connect/disconnect execute waiting".

(4)Operation failure may occur in some axes if the power supply of servo amplifiers connected after them on the SSCNET system is turned OFF. Be sure to use the disconnect function before turning OFF the power supply of any servo amplifiers connected after an amplifier whose power remains on.

(3)Procedure for connect/disconnect function to exchange the servo amplifier or SSCNET cable is shown below.

(a)Operation procedure to disconnect

1)Set the axis No. to disconnect in SD803. (Setting value: 1 to 32)

2)Check that "-1: Disconnect execute waiting" is set in SD508. (Disconnect execute waiting)

3)Set "-2: Disconnect execute command" in SD803.

4)Check that "0: Disconnect command accept waiting" is set in SD508. (Completion of disconnection)

5)Turn OFF the power supply of servo amplifier after checking its LED display for "AA" and then disconnect.

4 - 37

Contents

MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC Page For Safe Operations 1. Prevention of electric shocks 2. For fire prevention 3. For injury prevention 4. Various precautions (1) System structure (2) Parameter settings and programming (3) Transportation and installation Page (4) Wiring (5) Trial operation and adjustment (6) Usage methods (7) Corrective actions for errors (8) Maintenance, inspection and part replacement (9) About processing of waste (10) General cautions Page Page Page Page Page Page 1. OVERVIEW REMARK 1.2 Features 1.2.1Features of Motion CPU (1)Q series PLC Multiple CPU system (2)High speed operation processing (4)The operating system software package for your application needs 1.2.2Basic specifications of Q173DCPU/Q172DCPU (1)Module specifications (2)SV13/SV22 Motion control specifications/performance specifications (a) Motion control specifications Motion control specifications (continued) (b) Motion SFC Performance Specifications 1.3 Hardware Configuration 1.3.1 Motion system configuration (1) Equipment configuration in Q173DCPU/Q172DCPU system (2) Peripheral device configuration for the Q173DCPU/Q172DCPU 1.3.2 Q173DCPU System overall configuration Page 1.3.3 Q172DCPU System overall configuration Page 1.3.4 Software packages (1) Software packages (a) Operating system software (b) Motion controller programming software (2) Operating environment of personal computer (3)Operating system type/version (a)Confirmation method in the operating system (CD) (b)Confirmation method in MT Debeloper (4)Relevant software packages (a)PLC software package POINTS 1.3.5Restrictions on motion systems (1)Combination of Multiple CPU system (2)Motion modules (3)Other restrictions Page 2. MULTIPLE CPU SYSTEM 2.1.2 Installation position of CPU module Table 2.1 Example for CPU module installation 2.1.3 Precautions for using I/O modules and intelligent function modules (1) Modules controllable by the Motion CPU (2)Compatibility with the Multiple CPU system (3)Access range from non-controlledCPU Table 2.2 Access range to non-controlledmodule 2.1.4Modules subject to installation restrictions 2.1.5 How to reset the Multiple CPU system 2.1.6 Operation for CPU module stop error (1)When a stop error occurs at CPU No.1 (2) When a stop error occurs at CPU other than No.1 Page 2MULTIPLE CPU SYSTEM (3)Operation at a Motion CPU error 2.2 Starting Up the Multiple CPU System 2.2.1 Startup Flow of the Multiple CPU System Page 2.3.1CPU shared Memory (1)Structure of CPU shared memory Table 2.3 Table of self CPU operation information areas Page 2.3.2Multiple CPU high speed transmission (1)Multiple CPU high speed transmission Page (2) System configuration Table 2.4 System configuration to use Multiple CPU high speed transmission (3)Memory configuration of Multiple CPU high speed transmission area Table Description of area (4)Parameter setting Table 2.6 Multiple CPU high speed transmission parameter list Page Page Table 2.8 Parameter setting items of automatic refresh setting Page Page (5)Precautions 2.3.3 Multiple CPU high speed refresh function (1) Application example of Multiple CPU high speed refresh function (2)Operation example of Multiple CPU high speed refresh function Page Page 2.3.4 Clock synchronization between Multiple CPU (1) Setting of clock data (2) Synchronization of clock data (3) Information of clock (4) Error 2.3.5 Multiple CPU synchronous startup (1) Multiple CPU synchronous startup setting 2.3.6 Control Instruction from PLC CPU to Motion CPU Page 3. COMMON PARAMETERS 3.1.1 System data settings Page 3.1.2Common system parameters (1)Parameters for operating the Multiple CPU system 3COMMON PARAMETERS (2)Parameters common throughout the Multiple CPU system Table of Parameters cross-MultipleCPU system Page Page Page Page 3.1.3Individual parameters (1)System basic setting Page (2) Individual module settings Setting items for each module Setting items for each module (Continued) (3) External signal input 3.2 I/O number assignment 3.2.1 I/O number assignment of each module (1)Position of I/O number "0H (2)I/O number assignment of Motion CPU control module (3) Setting of the Motion CPU control modules by the PLC CPU 3.2.2 I/O number of each CPU modules 3.2.3 I/O number setting 3.3 Servo Parameters (1) Basic setting parameters (2) Gain/filter parameters (3) Extension setting parameters (4) I/O Setting Parameters 4. AUXILIARY AND APPLIED FUNCTIONS Page 4AUXILIARY AND APPLIED FUNCTIONS 4.1.2 Limit output setting data (1)Output device (2)Watch data (3)ON region setting (4)Output enable/disable bit (5)Forced output bit 4.2 Absolute Position System Page 4.2.1 Current value control 4.3 High-SpeedReading of Specified Data (1) Positioning data that can be set (2) Modules and signals to be used (3) Usable devices 4.4 ROM Operation Function 4.4.1 Specifications of 7-segmentLED/Switches (1) Operation mode Page 4.4.2 Outline of ROM operation Page Page Page Page 4.4.3 Operating procedure of the ROM operation function (1) ROM operation procedure (2) Operation at the "Mode operated by ROM 4.5 Security Function 4.5.1 Password registration/change (1)Procedure for password registration (2)Procedure for password change Page 4.5.2 Password delete (1)Procedure for password delete 4.5.3 Password check (1)Procedure for password check 4.5.4 Password save (1) Status of password data for each operation 4.6 All clear function (1)Procedure for clear all 4.7 Communication via Network 4.7.1Specifications of the communications via network 4.7.2Access range of the communications via network (1)Network configuration via the MELSECNET/10(H) or the Ethernet (2)Network configuration via the CC-Link (3)Network configuration via the RS-422/485 Network configuration which MELSECNET/10(H), Ethernet, CC- Link Page 4.8Monitor Function of the Main Cycle 4.9Servo Parameter Reading Function 4.10 Optional Data Monitor Function (1) Data that can be set (2) Devices that can be set 4.11 Connect/Disconnect Function (1) Connect/disconnect status devices (2) Connect/disconnect command devices Page Page Page Page 4.12 Remote operation 4.12.1 Remote RUN/STOP (1)Operation procedure Page 4.12.2 Remote latch clear Page APPENDICES Table 1.1 Special relay list Table 1.1 Special relay list (Continued) Page APPENDIX 1.2 Special registers Table 1.2 Special register list Table 1.2 Special register list (Continued) Page Page Page APPENDIX 1.3 Replacement of special relays/special registers Table 1.3 Replacement of special relays Table 1.4 Replacement of special registers APPENDIX 2 System Setting Errors Table 2.1 System Setting Errors Page APPENDIX 3 Self-diagnosiserror code (1) Multiple CPU related errors which occurs in Motion CPU Table 3.1 Multiple CPU related errors which occurs in Motion CPU (1000 to 9999) Page Page Page Page Page (2) Motion CPU-specificerrors Table 3.2 Motion CPU-specificerrors (10000 to 10999) Page (3) Self-diagnosticerror information (4) Release of Multiple CPU related error Table 4.1 Differences Between Q173DCPU/Q172DCPU and Q173HCPU/Q172HCPU Page APPENDIX 4.2 Comparison of devices (1)Motion registers Table 4.2 Motion registers (Monitor devices) list Table 4.3 Monitor devices list Table 4.4 Motion registers (Motion error history) list Table 4.5 Motion error history list (2) Special relays Table 4.6 Special relay list (3) Special registers Table 4.7 Special registers list Table 4.7 Special registers list (Continued) Other devices Table 4.8 Other devices list Table 4.8 Other devices list (Continued) APPENDIX 4.3 Differences of each mode Motion SFC Table 4.9 Differences in Motion SFC mode Virtual mode Table 4.10 Differences in Virtual mode