3 COMMON PARAMETERS

3.1.1 System data settings

The table below lists the system data items to be set.

 

 

Item

 

Setting range

Initial value

Remark

 

Base setting

Main base

 

8/12 slots

Main base: 8 slots

Set the number of slots in the main

 

Extension base

 

None/2/3/5/8/10/12 slots

None

base or extension base.

 

 

 

 

 

No. of CPU

 

2/3/4 modules

2 modules

Set the total number of Multiple

 

 

 

CPUs including PLC CPU(s).

 

 

 

 

 

 

 

 

 

 

Stop/do not stop all CPUs upon an

 

Set whether or not to stop the entire

 

 

Error operation mode at the

error in CPU No. 1 to 4.

Stop all CPUs upon error

 

 

stop of CPU

 

(The setting range varies depending

in CPU Nos. 1 to 4

system when a CPU stop error

 

 

 

occurs in each CPU.

 

 

 

 

on the number of Multiple CPUs.)

 

 

 

 

 

 

 

 

 

 

CPU

 

Varies depending on the

 

 

 

 

specific

0 to 14k points

 

 

 

 

number of CPUs.

 

 

Multiple CPU

Multiple CPU

send range

 

 

 

 

 

 

Common

setting

high speed

System

1 to 2k points

1

Refer to Section 2.3.2.

system

 

transmission

area

 

 

 

 

parameters

 

area setting

Automatic

Point : 2 to 14336 points

 

 

 

 

 

refresh

Start : Set target device for

None

 

 

 

 

setting

automatic refresh.

 

 

 

 

 

 

Set/do not set CPU No. 1 to 4 as the

 

 

 

 

Multiple CPU synchronous

synchronized startup.

Set CPU No. 1 to 4 as

Refer to Section 2.3.5.

 

 

startup setting

 

(The setting range varies depending

the synchronized startup.

 

 

 

 

on the number of Multiple CPUs.)

 

 

 

 

 

 

Within the main base and extension

 

Install the modules controlled by the

 

Motion slot

Module arrangement

None

self CPU in the main base and/or

 

 

 

base slots

 

extension base(s).

 

setting

 

 

 

 

 

Individual module

Varies depending on the module.

Varies depending on the

Set detailed items for each module

 

 

 

 

module.

controlled by the self CPU.

 

 

 

 

 

 

 

Operation cycle

 

0.4ms/0.8ms/1.7ms/3.5ms/7.1 ms/

Auto

Set the operation cycle of motion

 

 

 

14.2ms/Auto

control.

 

 

 

 

 

 

 

 

 

M2000 is turned on by switching

 

 

 

 

 

 

from STOP to RUN./M2000 is

M2000 is turned on by

Set the condition in which the PLC

 

 

Operation at STOP to RUN

turned on by switching from STOP

switching from STOP to

 

 

ready flag (M2000) turns on.

 

 

 

 

to RUN and setting 1 in the set

RUN.

 

 

 

 

 

 

 

 

 

register.

 

 

 

System basic

 

 

 

 

Set the bit device to use forced stop

 

setting

 

 

 

 

in the program.

Individual

 

Forced stop (Note-1)

None/X(PX) (0 to 1FFF)/

None

However, the forced stop input by

parameters

 

M (0 to 8191)

EMI terminal of Motion CPU module

 

 

 

 

 

 

 

 

 

 

cannot be invalidated using

 

 

 

 

 

 

parameter setting.

 

 

 

 

M (0 to 8191)/B (0 to 1FFF)/

 

Set the latch range of device

 

 

Latch range

 

F (0 to 2047)/D (0 to 8191)/

None

 

 

 

memory.

 

 

 

 

W (0 to 1FFF)

 

 

 

 

 

 

 

 

 

 

 

Set self CPU/other CPU/CPU

 

 

 

Self CPU installation position setting

(empty) for slots 0/1/2. (The setting

None

Set the installation position of the

 

range varies depending on the

self CPU in the main base.

 

 

 

 

 

 

 

 

 

number of Multiple CPUs installed.)

 

 

3 - 2