Siteupdateanttype Set Occupied Site Antenna | Novatel DL-V3 manual

B.40 SITEUPDATEANTTYPE Set Occupied Site Antenna

The siteupdateanttype command allows you to configure the site antenna type information (AntType field in the sitedef log) once the site has been occupied (by issuing a site enter command).

The siteupdateanttype set command sets the site antenna type for an occupied site to anttype.

The siteupdateanttype default and the siteupdateanttype clear commands clear the site antenna type for an occupied site.

The siteupdateanttype clear command clears the site antenna type for an occupied site.

Syntax

siteupdateanttype set [anttype] siteupdateanttype defaultclear

Message ID = 168

	Field	Data	Value Used if	Bytes	Format	Units	Offset
	Field	Data	Not Specified	Bytes	Format	Units	Offset
			Not Specified

	1	Header	-		-	-	0

	2	Parameter Update, see Table 34 on	-	4	Enum	none	H
		Page 107

	3	Antenna type	NUL	16	Char[]	none	H+4

	4	Reserved for future use	NUL	12	Char[]	none	H+20

Table 61: SITEUPDATEANTTYPE Default Configuration

Parameter	Power-On	Freset	Stored in NVM

AntType	clear	clear	NO

140	DL-V3 User Manual Rev 3

Image 140

Novatel DL-V3 user manual Siteupdateanttype Set Occupied Site Antenna, Siteupdateanttype Default Configuration

Contents

DL-V3 Proprietary Notice Table of Contents Oemv Family Receiver Performance DL-V3 Specifications Extcontrol Disable Automatic Powerup GroupControl COM Power for a Group 103 Edit Group Dgps ID Configuration 105 Table of Contents 114115 116 Bluetooth Configuration 195 Figures 199 197198 Tables Tables 126134 136 Software License Restrictions You may not Software License Terms and Conditions Standard Terms and Conditions of Sales Terms and Conditions Warranty FCC Notices What is the hazard? Lightning Protection NoticeHazard Impact Actions to Mitigate Lightning Hazards Description Electromagnetic Compatibility EMC and SafetyDL-V3 Regulatory Testing Weee Notice RoHS Notice Customer Service Oemv Firmware Upgrades Foreword CongratulationsScope Prerequisites Conventions Foreword DL-V3 Controller Models Model Name Firmware FeatureChapter Introduction Modes of Operation a DL-V3 Model RT20 L1/L2 Chapter IntroductionGPS Positioning Modes of Operation Chapter Installation and Setup DL-V3 Setup Chapter Installation and Setup Antenna Port Installation and Setup Chapter Ethernet Port DB-9 Setup Bluetooth Setup Installing the PC Utilities Selecting a Gnss Antenna Power Supply Requirements Choosing a Coaxial CableNovAtel Gnss Antenna Models Models Frequencies Supported Connecting the Antenna to the Receiver Applying Power to the ReceiverEnclosure Power Requirements Mounting Bracket Connecting Data Communications Equipment DL-V3 Power Down and the Power ButtonDefault Serial Port Configurations Receiver Universal Serial Bus USB DL-V3 COM3 ConfigurationStrobes Status Communication Ports excluding COM3 Status IndicatorsPower Positioning Mode Satellite TrackingSatellite Tracking LEDs Flash Card Memory Positioning Mode LEDs Position Mode Position Mode Detail a External Oscillator Occupation TimeOccupation Time LEDs Baseline Length LED Color Antenna LNA Power DL-V3 Removable Compact Flash Memory Card Access Door Data Logging Using CDU to Format the CF Card Card Choice Using HyperTerminal to Format the CF Card Installation and Setup Chapter Serial Port Default Settings Chapter Operation Communicating Using a Remote Terminal Communicating Using a Personal ComputerCommunicating with the Receiver Using CDU Starting the Receiver Chapter Operation Transmitting and Receiving Corrections Rover Base Base Station Configuration Log port message trigger period Rover Station Configuration Configuration Notes Using the DL-V3 Log Data from a Site to a File Start the Data Logging Select the GroupEdit the Site Enabling Sbas Positioning Stop the Data Logging Pass-Through Logging Sync Option Chapter DL Explorer Starting DL Explorer DL Explorer Chapter Exiting DL ExplorerReceiver Groups Chapter DL Explorer Logs Tab Log Triggers Trigger Description Preset Powerup Group Position Tab Position Tab Site Tab Site Tab Interfaces Tab Interfaces Tab Ports Tab Ports Tab Communication Parameters COM Parameters Upload Group from the PC/Laptop to the Receiver Group Management Starting Groups Transfer a File from the DL-V3 to the PC/Laptop Log Transfer Dialog File Details Flight Recorder Flight Recorder OFF CF Card Status CF Card Status Appendix a Oemv Family Receiver Performance DL-V3 Specifications Color Length km Color LEDs ColorBaseline Dimensions Oemv Firmware Reference Manual DL-V3 Serial Port Pin-Out DescriptionsDL-V3 I/O Port Pin-Out Descriptions 2.1 12V Power Adapter Cable NovAtel part number DL-V3 Power Cable Null-modem Cable NovAtel part number Reference Description Straight Through Serial Cable NovAtel part number DL-V3 Straight Through Serial Cable Wiring Table 2.4 I/O Strobe Port Cable NovAtel part number DL-V3 Commands in Alphabetical Order Message ID Ascii Command Description DL-V3 Commands in Order of their Message IDs Message ID Ascii Command Description Syntax Conventions Appcontrol COM3 Bluetooth/Ethernet Switch Dhcp OFF Application Functions Application ParametersBinary BinaryASCII Comvout Control COM Peripheral Power COM Serial Port Identifiers Default COM Voltage Out Action Dump Mode Currentfile Default ConfigurationParameter Power-On Freset Stored in NVM Currentfile Specify File for FILEHDR/FILETRANSER Logs Currentgroup Default Configuration Currentgroup Specify File for Groupdef Log DEL Delete Files from CF Card Delete Target Disk Format the CF Card CF Card Operation Extcontrol Disable Automatic Powerup Group Freset Clear Selected Data from NVM and Reset Freset Target Group Create and Manipulate Groups Group Default Configuration Action Groupantheight Default Configuration Groupantheight Edit Group Antenna Height Groupantsn Default Configuration Groupantsn Edit Group Antenna Serial Number Groupanttype Default Configuration Groupanttype Edit Group Antenna Type Groupcom Associate Port Configurations with a Group Parameter Update 101 102 ParityHandshaking Groupcomvout Control COM Power for a Group Example 104 Groupdgpstxid Edit Group Dgps ID Configuration Dgps Type, see on Page 165 and Table 106 Groupdgpstxid Default ConfigurationField Power-On Freset Stored in NVM Groupecutoff Default Configuration Groupecutoff Edit Group Elevation Cut-Off Angle Groupfixpos Configure Group to Fix Receiver Position Groupfixpos Default Configuration Groupinterfacemode Edit Group Interface Mode 110 Groupinterfacemode Default ConfigurationParameter Power-On Freseta Stored in NVM Grouplog Edit Group Logging Specifications Grouplog Default Configuration 112 Groupmode Default Configuration Groupmode Configure Group Survey TypeGroup Mode Groupposave Configure Group Position Averaging Groupsave Default Configuration Groupsatlimit Default Configuration Groupsatlimit Limit Number of Satellites for Group Groupsitename Default Configuration Groupsitename Edit Group Site Name Groupsitenumber Default Configuration Groupsitenumber Edit Group Site Number Groupuse Execute a Set of Commands Log hdrdst versionb command is issued Group Action 119 LOG Request Logs from the Receiver Factory Default 121 122 Description Field Name Value Type Detailed Serial Port Identifiers 123 124 XCOM3 Logfile Open or Close File on CF Card Logfile Default Configuration Log File Action Methumid Default Configuration Methumid Specify Air Humidity Metpress Default Configuration Metpress Specify Air Pressure Mettemp Specify Air Temperature Mettemp Default Configuration Project Action Project Default ConfigurationProject Add or Clear a Project Rename Rename a File on the CF Card Reset Perform a Hardware Reset Satlimit Set Minimum Satellites in Position Solution Satlimit Default Configuration File Port Channel Site Control Site Occupations Site Mode Site Default Configuration Siteupdatenumber Set Occupied Site Number Siteupdatenumber Default Configuration Siteupdatename Set Occupied Site Name Siteupdatename Default Configuration Siteupdateantheight Set Occupied Site Height Siteupdateantheight Default Configuration Siteupdateanttype Set Occupied Site Antenna Siteupdateanttype Default Configuration Siteupdateattribute Set Occupied Site Attributes Siteupdateattribute Default Configuration Softpower Simulate a Power-Button Off Softpower Write Create User Data Logs Writefile Create/Append Files on CF Card Writefilehex Create/Append Data to CF Card Writehex Create User Data Logs DL-V3 Logs in Alphabetical Order Message ID Ascii Log Description DL-V3 Logs in Order of their Message IDs Message Ascii Log Description PDC Log Header Type Size Description Range Offset Serial Port Identifiers Port Identifier Description Binary Value Ascii Mode Name Description Serial Port Interface Modes 152 Generic Currentset CURRENTFILE/CURRENTGROUP Configuration Field Data Description Bytes Format Units Offset Dirent CF Card File List 155 Extlevels Extended Hardware Levels Filechannel Log File Channel Configuration Filehdr Logfile Header File Status File Status Bit Description Bit=0 Bit=1 Filetransfer Log File Contents Groupcomconfig COM Port Configuration Information Groupcomconfig Status Word Status Bit Description Bit=0 Bit=1 Groupdef Log Group Configuration 164 Dgps Type Description Binary Dgps TypeCOM1/COM2 Interface Modes Group Status1 Word Group Status Bit Description Bit=0 Bit=1 Group Status2 Word Met Status Bit Description Bit=0 Bit=1 Metdef Meteorological ParametersMeteorological Log Status Projectdef Pwrstatus Power and Status Settings Summary DL-V3 Voltage Parameter Logs Port Power Status Power Status Bits Description Bit = AUX2 Bit Description Bit=0 Bit=1 Trigger Rxstatus DL-V3 StatusAuxiliary 2 Status Word Auxiliary 3 Status Word AUX3 Bit Description Bit=0 Bit=1 Trigger 174 Rxstatusevent DL-V3 Status Event Notification SiteStatus Bit Bit Name Description Bit=0 Bit=1 Site ConfigurationSite Status Version HW & SW Versions and Serial Numbers Write User-Generated InformationWritehex User-Generated Information Component Type Appendix D Physical Set-Up Configuration Overview 179 Enable Ethernet on the DL-V3 Receiver 180 181 182 183 184 Network Settings Configuration 185 Lantronix COM Redirector Manager 186 187 Configure Virtual Serial PortAdd the DL-V3 Ethernet Device’s IP Address and Port 188 Alternative Serial ConfigurationRedirector Configuration Completion HyperTerminal Default Parameters Switch to Ethernet Device Reset Ethernet Establish Serial Command Mode in EthernetEstablish a Communications Tunnel 190 Command Mode Example 191 Network Configuration in Command Mode 192 193 194 195 Enable Bluetooth on the DL-V3 ReceiverSet Up a PC/Laptop with a Bluetooth Adaptor Locate a Bluetooth-Enabled DL-V3 in Range 196 Communicate with the DL-V3 Using Bluetooth Bluetooth PIN Code Request Stop Communicating with the DL-V3 Using Bluetooth Bluetooth Connected Green COM3 Disconnect? 200 AccessoriesManufacturer’s Part Number Index 201 Index 202 CF card, 39, 41, 92 collect, 40, 51, 53 203 Bluetooth, 27 204 LED 205 Base, 47, 49 206 RTK, 24 207 OM-20000119 Rev 2009/07/22