Null-modem Cable NovAtel part number | Novatel DL-V3 specs

A.2.2.2 Null-modem Cable (NovAtel part number 01017658)

This cable supplied with the DL-V3, see Figure 35 below, provides an easy means of communications with a PC/laptop. The cable is equipped with a 9-pin connector at the receiver end which can be plugged into the COM1, COM2, or AUX port. At the PC/laptop end, a 9-pin connector is provided to accommodate a PC/laptop serial (RS-232) communication port.

This cable is RoHS compliant.

5	1						5	1
9	6						9	6
								11
Wiring Table:
	Connector				Pin Number
	To DB9S (10)	2	3	8	7	4	5	1 & 6
	To DB9S (11)	3	2	7	8	1 & 6	5	4

Reference Description

10DB9S (Female)

11DB9S (Female)

Figure 35: DL-V3 Null-Modem Cable

78	DL-V3 User Manual Rev 3

Image 78

Novatel DL-V3 user manual Null-modem Cable NovAtel part number, Reference Description

Contents

DL-V3 Proprietary Notice Table of Contents Control COM Power for a Group 103 Oemv Family Receiver Performance DL-V3 SpecificationsExtcontrol Disable Automatic Powerup Group Edit Group Dgps ID Configuration 105 115 Table of Contents114 116 Bluetooth Configuration 195 Figures 197 198199 Tables 134 Tables126 136 Software License Restrictions You may not Software License Terms and Conditions Standard Terms and Conditions of Sales Terms and Conditions Warranty FCC Notices Hazard Impact What is the hazard?Lightning Protection Notice Actions to Mitigate Lightning Hazards Electromagnetic Compatibility EMC and Safety DL-V3 Regulatory TestingDescription Weee Notice RoHS Notice Customer Service Oemv Firmware Upgrades Scope ForewordCongratulations Prerequisites Conventions Foreword Model Name Firmware Feature Chapter IntroductionDL-V3 Controller Models Chapter Introduction GPS Positioning Modes of OperationModes of Operation a DL-V3 Model RT20 L1/L2 Chapter Installation and Setup DL-V3 Setup Chapter Installation and Setup Antenna Port Installation and Setup Chapter Ethernet Port DB-9 Setup Bluetooth Setup Installing the PC Utilities Selecting a Gnss Antenna NovAtel Gnss Antenna Models Power Supply RequirementsChoosing a Coaxial Cable Models Frequencies Supported Enclosure Power Requirements Connecting the Antenna to the ReceiverApplying Power to the Receiver Mounting Bracket Default Serial Port Configurations Connecting Data Communications EquipmentDL-V3 Power Down and the Power Button Receiver DL-V3 COM3 Configuration StrobesUniversal Serial Bus USB Status Indicators PowerStatus Communication Ports excluding COM3 Satellite Tracking LEDs Positioning ModeSatellite Tracking Flash Card Memory Positioning Mode LEDs Position Mode Position Mode Detail a Occupation Time LEDs External OscillatorOccupation Time Baseline Length LED Color Antenna LNA Power DL-V3 Removable Compact Flash Memory Card Access Door Data Logging Using CDU to Format the CF Card Card Choice Using HyperTerminal to Format the CF Card Installation and Setup Chapter Serial Port Default Settings Chapter Operation Communicating with the Receiver Using CDU Communicating Using a Remote TerminalCommunicating Using a Personal Computer Starting the Receiver Chapter Operation Transmitting and Receiving Corrections Rover Base Base Station Configuration Log port message trigger period Rover Station Configuration Configuration Notes Using the DL-V3 Log Data from a Site to a File Select the Group Edit the SiteStart the Data Logging Enabling Sbas Positioning Stop the Data Logging Pass-Through Logging Sync Option Chapter DL Explorer Starting DL Explorer Exiting DL Explorer Receiver GroupsDL Explorer Chapter Chapter DL Explorer Logs Tab Log Triggers Trigger Description Preset Powerup Group Position Tab Position Tab Site Tab Site Tab Interfaces Tab Interfaces Tab Ports Tab Ports Tab Communication Parameters COM Parameters Upload Group from the PC/Laptop to the Receiver Group Management Starting Groups Transfer a File from the DL-V3 to the PC/Laptop Log Transfer Dialog File Details Flight Recorder Flight Recorder OFF CF Card Status CF Card Status Appendix a Oemv Family Receiver Performance DL-V3 Specifications Color LEDs Color BaselineLength km Color Dimensions DL-V3 Serial Port Pin-Out Descriptions DL-V3 I/O Port Pin-Out DescriptionsOemv Firmware Reference Manual 2.1 12V Power Adapter Cable NovAtel part number DL-V3 Power Cable Null-modem Cable NovAtel part number Reference Description Straight Through Serial Cable NovAtel part number DL-V3 Straight Through Serial Cable Wiring Table 2.4 I/O Strobe Port Cable NovAtel part number DL-V3 Commands in Alphabetical Order Message ID Ascii Command Description DL-V3 Commands in Order of their Message IDs Message ID Ascii Command Description Syntax Conventions Appcontrol COM3 Bluetooth/Ethernet Switch Dhcp OFF Binary Application FunctionsApplication Parameters BinaryASCII Comvout Control COM Peripheral Power COM Serial Port Identifiers Default COM Voltage Out Action Parameter Power-On Freset Stored in NVM Dump ModeCurrentfile Default Configuration Currentfile Specify File for FILEHDR/FILETRANSER Logs Currentgroup Default Configuration Currentgroup Specify File for Groupdef Log DEL Delete Files from CF Card Delete Target Disk Format the CF Card CF Card Operation Extcontrol Disable Automatic Powerup Group Freset Clear Selected Data from NVM and Reset Freset Target Group Create and Manipulate Groups Group Default Configuration Action Groupantheight Default Configuration Groupantheight Edit Group Antenna Height Groupantsn Default Configuration Groupantsn Edit Group Antenna Serial Number Groupanttype Default Configuration Groupanttype Edit Group Antenna Type Groupcom Associate Port Configurations with a Group Parameter Update 101 Parity Handshaking102 Groupcomvout Control COM Power for a Group Example 104 Groupdgpstxid Edit Group Dgps ID Configuration Dgps Type, see on Page 165 and Table Groupdgpstxid Default Configuration Field Power-On Freset Stored in NVM106 Groupecutoff Default Configuration Groupecutoff Edit Group Elevation Cut-Off Angle Groupfixpos Configure Group to Fix Receiver Position Groupfixpos Default Configuration Groupinterfacemode Edit Group Interface Mode Groupinterfacemode Default Configuration Parameter Power-On Freseta Stored in NVM110 Grouplog Edit Group Logging Specifications Grouplog Default Configuration 112 Groupmode Configure Group Survey Type Group ModeGroupmode Default Configuration Groupposave Configure Group Position Averaging Groupsave Default Configuration Groupsatlimit Default Configuration Groupsatlimit Limit Number of Satellites for Group Groupsitename Default Configuration Groupsitename Edit Group Site Name Groupsitenumber Default Configuration Groupsitenumber Edit Group Site Number Groupuse Execute a Set of Commands Log hdrdst versionb command is issued Group Action 119 LOG Request Logs from the Receiver Factory Default 121 122 Description Field Name Value Type Detailed Serial Port Identifiers 123 124 XCOM3 Logfile Open or Close File on CF Card Logfile Default Configuration Log File Action Methumid Default Configuration Methumid Specify Air Humidity Metpress Default Configuration Metpress Specify Air Pressure Mettemp Specify Air Temperature Mettemp Default Configuration Project Default Configuration Project Add or Clear a ProjectProject Action Rename Rename a File on the CF Card Reset Perform a Hardware Reset Satlimit Set Minimum Satellites in Position Solution Satlimit Default Configuration File Port Channel Site Control Site Occupations Site Mode Site Default Configuration Siteupdatenumber Set Occupied Site Number Siteupdatenumber Default Configuration Siteupdatename Set Occupied Site Name Siteupdatename Default Configuration Siteupdateantheight Set Occupied Site Height Siteupdateantheight Default Configuration Siteupdateanttype Set Occupied Site Antenna Siteupdateanttype Default Configuration Siteupdateattribute Set Occupied Site Attributes Siteupdateattribute Default Configuration Softpower Simulate a Power-Button Off Softpower Write Create User Data Logs Writefile Create/Append Files on CF Card Writefilehex Create/Append Data to CF Card Writehex Create User Data Logs DL-V3 Logs in Alphabetical Order Message ID Ascii Log Description DL-V3 Logs in Order of their Message IDs Message Ascii Log Description PDC Log Header Type Size Description Range Offset Serial Port Identifiers Port Identifier Description Binary Value Ascii Mode Name Description Serial Port Interface Modes 152 Generic Currentset CURRENTFILE/CURRENTGROUP Configuration Field Data Description Bytes Format Units Offset Dirent CF Card File List 155 Extlevels Extended Hardware Levels Filechannel Log File Channel Configuration Filehdr Logfile Header File Status File Status Bit Description Bit=0 Bit=1 Filetransfer Log File Contents Groupcomconfig COM Port Configuration Information Groupcomconfig Status Word Status Bit Description Bit=0 Bit=1 Groupdef Log Group Configuration 164 Dgps Type COM1/COM2 Interface ModesDgps Type Description Binary Group Status1 Word Group Status Bit Description Bit=0 Bit=1 Group Status2 Word Metdef Meteorological Parameters Meteorological Log StatusMet Status Bit Description Bit=0 Bit=1 Projectdef Pwrstatus Power and Status Settings Summary DL-V3 Voltage Parameter Logs Port Power Status Power Status Bits Description Bit = Rxstatus DL-V3 Status Auxiliary 2 Status WordAUX2 Bit Description Bit=0 Bit=1 Trigger Auxiliary 3 Status Word AUX3 Bit Description Bit=0 Bit=1 Trigger 174 Rxstatusevent DL-V3 Status Event Notification Site Configuration Site StatusSiteStatus Bit Bit Name Description Bit=0 Bit=1 Writehex User-Generated Information Version HW & SW Versions and Serial NumbersWrite User-Generated Information Component Type Appendix D Physical Set-Up Configuration Overview 179 Enable Ethernet on the DL-V3 Receiver 180 181 182 183 184 Network Settings Configuration 185 Lantronix COM Redirector Manager 186 Configure Virtual Serial Port Add the DL-V3 Ethernet Device’s IP Address and Port187 Alternative Serial Configuration Redirector Configuration Completion188 HyperTerminal Default Parameters Switch to Ethernet Device Establish a Communications Tunnel Reset EthernetEstablish Serial Command Mode in Ethernet 190 Command Mode Example 191 Network Configuration in Command Mode 192 193 194 Enable Bluetooth on the DL-V3 Receiver Set Up a PC/Laptop with a Bluetooth Adaptor195 Locate a Bluetooth-Enabled DL-V3 in Range 196 Communicate with the DL-V3 Using Bluetooth Bluetooth PIN Code Request Stop Communicating with the DL-V3 Using Bluetooth Bluetooth Connected Green COM3 Disconnect? Accessories Manufacturer’s Part Number200 Index 201 Index 202 CF card, 39, 41, 92 collect, 40, 51, 53 203 Bluetooth, 27 204 LED 205 Base, 47, 49 206 RTK, 24 207 OM-20000119 Rev 2009/07/22