Panasonic AJ-PX5000G manual 138

Chapter 7 Menu Operations — Menu list

Item	Description of settings	Remark
[R‑Mg (PHASE)]	Corrects the hue between red and magenta.
	[−63]…[5]…[63]
[Mg (PHASE)]	Corrects the magenta hue.
	[−63]…[3]…[63]
[Mg‑B (PHASE)]	Corrects the hue between magenta and blue.
	[−63]…[4]…[63]
[B (PHASE)]	Corrects the blue hue.
	[−63]…[0]…[63]
[B‑Cy (PHASE)]	Corrects the hue between blue and cyan.
	[−63]…[0]…[63]
[Cy (PHASE)]	Corrects the cyan hue.
	[−63]…[12]…[63]
[Cy‑G (PHASE)]	Corrects the hue between cyan and green.
	[−63]…[15]…[63]
[G (PHASE)]	Corrects the green hue.
	[−63]…[10]…[63]
[G‑Yl (PHASE)]	Corrects the hue between green and yellow.
	[−63]…[10]…[63]
[Yl (PHASE)]	Corrects the yellow hue.
	[−63]…[6]…[63]
[Yl‑Yl‑R (PHASE)]	Corrects the hue between yellow and “colors between yellow and red”.
	[−63]…[22]…[63]
[Yl‑R (PHASE)]	Corrects the hue between yellow and red.
	[−63]…[7]…[63]
[Yl‑R‑R (PHASE)]	Corrects the hue between “colors between yellow and red” and red.
	[−63]…[13]…[63]
			are factory settings.

ffWhen saving or reading setup files from an SD memory card, you can save items with an [S] and items without an [S] separately. Items with an [S] in front of the item name are the targets for [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT]. Items without an [S] are targets for [PAINT(LEVEL)].

[LOW SETTING]

Item		Description of settings	Remark
[[S] MASTER GAIN]	Selects the master gain.		ff[−6dB] in [[S] MASTER GAIN] cannot be selected
	[−6dB], [−3dB], [0dB], [3dB], [6dB], [9dB], [12dB], [15dB], [18dB], [21dB],		when [NORMAL] is set in main menu → [PAINT]
	[24dB], [27dB], [30dB]		→ [[S] CAMERA SETTING] → [SHOOTING
[H.DTL LEVEL]	Sets the horizontal detail correction level.		MODE].
			ffA coloration phenomenon may occur in videos
	[0]…[12]…[63]
[V.DTL LEVEL]	Sets the vertical detail correction level.		of high-brightness areas if shooting was done
			with the master gain set to [−6dB] or [−3dB].
	[0]…[15]…[31]
			After switching the <OUTPUT>/<AUTO KNEE>
[DTL CORING]	Sets the detail noise removal level.
			selection switch to <CAM>/<OFF> and setting
	[0]…[1]…[60]
			[ON] in the main menu → [PAINT] → [KNEE/
[H.DTL FREQ.]	Selects the horizontal detail frequency.		LEVEL] → [[S] MANUAL KNEE], you can reduce
	[0]…[18]…[31]		the coloration phenomenon by changing the
[LEVEL DEPEND.]	Sets [LEVEL DEPEND.].		following menu items:
			- Reduce the [KNEE MASTER SLOPE] value of
	Compresses the details of dark areas when Y detail is emphasized.
	Details of bright areas are also compressed if the value is large.		[KNEE/LEVEL] when [HD], [SD], [FILMLIKE1],
	[0], [1]…[5]		[FILMLIKE2], or [FILMLIKE3] is selected in the
[MASTER GAMMA]	Sets the master gamma in 0.01 steps.		main menu → [PAINT] → [GAMMA] → [GAMMA
			MODE SEL].
	[0.30]…[0.45]…[0.75]
			- Reduce the [F‑REC DYNAMIC LVL] value of
[BLACK GAMMA]	Sets the gamma curves of dark areas.
			[GAMMA] when [FILM‑REC] is selected in main
	[−8]…[−1]	Compresses the dark areas.	menu → [PAINT] → [GAMMA] → [GAMMA
	[OFF]	Standard state	MODE SEL].
			- Reduce the [V‑REC KNEE SLOPE] value of
	[1]…[8]	Expands the dark areas.
			[GAMMA] when [VIDEO‑REC] is selected in the
[B. GAMMA RANGE]	Sets the maximum level of compression/expansion.
			main menu → [PAINT] → [GAMMA] → [GAMMA
	[1]	About 20%	MODE SEL].
	[2]	About 30%
	[3]	About 40%
[[S] MATRIX TABLE]	Selects the color collection table for the linear matrix.
	[A], [B], [OFF]
[[S] COLOR	Switches the 15-axis independent color correction on/off.
CORRECT]	[ON], [OFF]

are factory settings.

ffWhen saving or reading setup files from an SD memory card, you can save items with an [S] and items without an [S] separately. Items with an [S] in front of the item name are the targets for [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT]. Items without an [S] are targets for [PAINT(LEVEL)].

– 138 –