Chapter 4 Adjustments and Settings for
[SDI OUT2] | — | Displays the status of the signal output from the <SDI OUT2> terminal. |
| [OUTPUT] | Displays the status of [MEM]/[CAM] or [OFF] set by [SDI OUT2] and [MONITOR OUT |
| MODE] in the main menu → [I/F SETUP] → [OUTPUT SEL]. | |
|
| |
| [SELECT] | Displays the signal format set by [SDI2/HDMI OUT] and [1080P SDI2/HDMI OUT] in the |
| main menu → [I/F SETUP] → [OUTPUT SEL] by [SYSTEM]/[DOWNCON]/[1080i]. | |
|
| |
| [CHAR] | Displays the position of the <MON OUT CHARATER> switch by [ON]/[OFF]. |
[P2CARD STATUS] |
| Displays the status of the P2 card inserted in the card slot, remaining capacity and total |
|
| used capacity. |
| — | The statuses of cards to be displayed are as follows: |
| [ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/ | |
|
| |
|
| [FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD] |
|
| For details, refer to “P2 card access LEDs and status of P2 cards” (page 32). |
| [TOTAL P2/mP2] | Displays the remaining capacity/total capacity totaled for slots 1/2 (or slots 3/4) and the |
| recording medium ([P2] or [mP2]). | |
|
| |
| [SLOT1] or [SLOT3] | Displays the status of the P2 card in slot 1 (or slot 3) and remaining capacity/total capacity. |
| [SLOT2] or [SLOT4] | Displays the status of the P2 card in slot 2 (or slot 4) and remaining capacity/total capacity. |
[PROXY] | [MEDIA] | Displays the media selection status for proxy recording. |
| [P2]/[P2&SD]/[OFF] | |
|
| |
| [MODE] | Displays the setting status for proxy recording mode. |
| [STD 2CH MP4]/[SHQ 2CH MOV]/[HQ 4CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV] | |
|
| |
| [SUPER] | Displays the superimposed setting status of the time code. |
| [UPPER]/[LOWER]/[OFF] | |
|
| |
| [PROXY ERROR] | Displays the operation error on the proxy module. |
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
[SAMPLE RES] | — | Displays the number of audio recording bits. |
[MIC POWER (MENU)] | — | Displays the menu setting status of power supply to the microphone. |
| [FRONT] | Displays the power supply status to the front microphone currently set in the main menu → |
| [I/F SETUP] → [MIC/AUDIO] → [FRONT MIC POWER] by [ON]/[OFF]. | |
|
| |
|
| Displays whether to set supply of power to the microphone on the <AUDIO IN> terminal at |
|
| the rear in the main menu → [I/F SETUP] → [MIC/AUDIO] → [REAR MIC POWER]. |
| [REAR] | ff[OFF]: Power is not supplied to the microphone. |
|
| ff[ON]: Power is supplied to the microphone when the <LINE>/<MIC> selector switch is set |
|
| to <MIC> and the microphone input power selector switch is set to <+48V>. |
[VR SELECT] | — | Displays which of [CH1/2] and [CH3/4] the audio level adjustment dial is to be set as |
| enabled to in the main menu → [I/F SETUP] → [MIC/AUDIO] → [VR SELECT]. | |
|
| |
[LEVEL] |
| Displays the recording level adjustment method currently selected on each channel. |
|
| ff[VR]: Displayed when manual adjustment using the adjustment dial is set. |
| [CH1/2/3/4] | ff[MENU]: Displayed when manual adjustment using [LVL CONTROL CH3(CH1)]/[LVL |
|
| CONTROL CH4(CH2)] is set in the main menu → [I/F SETUP] → [MIC/AUDIO]. |
|
| ff[AUTO]: Displayed when automatic adjustment is set. |
[F.VR] | [CH1/2/3/4] | Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to |
| which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL]. | |
|
| |
[A.IN] | [CH1/2/3/4] | Displays the input status of each channel by [FRONT] (front)/[REAR] (rear)/[W.L.] |
| (wireless). | |
|
| |
[METER] | [CH1/2/3/4] | Displays the recording level of each channel. |
[CAC INFO] screen
Displays the operation status or information of CAC.
[CAC CONT] | Displays the operation status of CAC. |
| ff[ON]: [ON] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], and CAC is active. |
| ff[STOP]: [ON] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], however, CAC operation |
| stops under certain data or lens conditions. |
| ff[OFF]: [OFF] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], and CAC is not active. |
[CAC MODE] | Displays the operation mode of CAC. |
| ff[AUTO]: The CAC file is automatically selected. |
[CONNECT LENS TYPE] | Displays the lens ID of the currently connected digital lens. |
[SELECT FILE TITLE] | Displays the title and the file version of the CAC file currently used in the operation. The CAC file can be set in the main menu |
| → [MAINTENANCE] → [CAC ADJ]. |
[CAC WARNING] | Displays a warning when operation of CAC has stopped. |
| ff[CAC LENS DATA INVALID]: This is displayed, for example, when the response data from the lens is not supported. |
| ff[LENS INIT. NOT COMPLETED]: This is displayed, for example, when initialization of the lens cannot complete. |