Chapter 7 Menu
[VF DISPLAY]
Item |
| Description of settings | Remark |
[VF/LCD CHAR] | Selects whether to display a character on the image of the LCD monitor and |
| |
| viewfinder. |
|
|
| [ON] | Displays a character on both the viewfinder and LCD monitor. |
|
| [VF‑OFF] | Does not superimpose on the viewfinder, and displays on the |
|
|
| LCD monitor. |
|
| [LCD‑OFF] | Does not superimpose on the LCD monitor, and displays on the |
|
|
| viewfinder. |
|
[VF MODE] | Selects a viewfinder image. | ffThis item is enabled when [CAM] is set in the | |
|
|
| main menu → [SYSTEM] → [SYSTEM MODE] |
| [MEM] | In playback mode, these are playback images. | → [REC SIGNAL]. When [SDI] is set, playback |
|
|
| images are output in the playback mode |
| [CAM] | Always camera images. | |
| regardless of this setting. | ||
|
|
| |
|
|
|
|
[VF COLOR] | Selects whether to display viewfinder images in color or in black and white. |
| |
| [ON] | Displays in color. |
|
| [OFF] | Displays in black and white (playback images, thumbnail |
|
|
| screens and menu displays remain in color). |
|
[DISP CONDITION] | Selects the status display method. |
| |
| [NORMAL] | Status is always displayed. |
|
| [HOLD] | Normally, status is not displayed. Push the <MARKER |
|
|
| SEL>/<MODE CHECK/MENU CANCEL> switch towards the |
|
|
| <MCK/MCL> side to display when the mode check screen is |
|
|
| displayed. |
|
[DISP MODE] | Shows/hides camera warning/notification displayed in the center of the viewfinder. |
| |
| For details, refer to “Display modes and setting changes/adjustment result |
| |
| messages” (page 79). |
| |
| [1], [2], [3] |
|
|
[VF OUT] | Selects the image signal displayed on the viewfinder screen. |
| |
| [Y] | Luminosity signal |
|
| [NAM] | Outputs the [R], [G] or [B] signal with the largest level. |
|
| [R] | Rch signal |
|
| [G] | Gch signal |
|
| [B] | Bch signal |
|
[VF DTL] | Sets the detail level of the viewfinder screen. |
| |
| Further emphasizes details of the viewfinder signal. If [0], the detail is the same as |
| |
| this line. |
|
|
| [0]…[5]…[10] |
|
|
[ZEBRA1 DETECT] | Sets the ZEBRA1 extraction level (IRE value). |
| |
| [0%]…[70%]…[109%] |
| |
[ZEBRA2 DETECT] | Sets the ZEBRA2 extraction level (IRE value). |
| |
| [0%]…[85%]…[109%] |
| |
[ZEBRA2] | Switches [ZEBRA2] [ON]/[OFF] and selects SPOT. |
| |
| [ON], [SPOT], [OFF] |
| |
[LOW LIGHT LVL] | Sets how low the amount of light entering the camera must be to display [LOW |
| |
| LIGHT]. |
|
|
| [OFF], [10%], [15%], [20%], [25%], [30%], [35%] |
| |
[RC MENU DISP.] | Sets whether to display the menu on the viewfinder screen when the remote |
| |
| control unit or extension control unit is connected. |
| |
| [ON], [OFF] |
|
|
[MARKER/CHAR LVL] | Configures settings for the viewfinder marker and character luminosity. |
| |
| [50%], [60%], [70%], [80%], [90%], [100%] |
| |
[SYNCHRO SCAN | Sets the unit in which synchro scan mode is displayed. |
| |
DISP] | [sec] | Displays in time. |
|
|
| ||
| [deg] | Displays at shutter open angle. |
|
are factory settings.