Chapter 7 Menu
[BATTERY/P2CARD]
Item |
| Description of settings | Remark | ||
[BATTERY SELECT] | Selects the battery to use. | ffWhen the battery charge level percentage | |||
| [HYTRON140] | Detects the battery charge level according to the selected | cannot be detected, it will follow the setting value | ||
| of [TYPE A] even if it is set to [BATT STAT] or | ||||
| [DIONIC90] | battery when the Anton/Bauer HYTRON140 or DIONIC90, the | |||
| [ENDURA STAT]. Make sure that the [TYPE A] | ||||
| IDX ENDURA10 (E‑10), and the PAG PAG L96e are selected. | ||||
| [ENDURA10] | ||||
| setting values [FULL] (fully charged), [NEAR END] | ||||
|
| ||||
| [PAG L96e] |
| (near end), or [END] (end) is appropriate for the | ||
| [TYPE A] | Select any item when a battery other than [HYTRON140], | battery being used. | ||
|
|
|
| ||
| [TYPE B] | [DIONIC90], [ENDURA10], or [PAG L96e] is used. At this |
|
|
|
| time, set [FULL] (full voltage), [NEAR END] (near end warning |
|
|
| |
| [TYPE C] |
|
|
| |
| voltage), and [END] (end voltage) in the main menu → [I/F |
|
|
| |
|
|
|
|
| |
|
| SETUP] → [BATTERY SETTING] (page 163) according to the |
|
|
|
|
| battery in use. |
|
|
|
| [BATT STAT] | When using a battery whose charge level is detected as a |
|
|
|
|
| percentage value, near end and end operation is conducted |
|
|
|
|
| according to the percentage value of the charge level if |
|
|
|
|
| [BATT STAT] is selected. Set the percentage value of [BATT |
|
|
|
|
| STAT NEAR END] (near end) and [BATT STAT END] (end) |
|
|
|
|
| in the main menu → [I/F SETUP] → [BATTERY SETTING] |
|
|
|
|
| (page 163) according to the battery in use. |
|
|
|
| [ENDURA | Select when IDX ENDURA battery is used to operate at near |
|
|
|
| STAT] | end and end according to the percentage value of the charge |
|
|
|
|
| level information. Set the percentage value of [ENDURA STAT |
|
|
|
|
| NEAR END] (near end) and [ENDURA STAT END] (end) |
|
|
|
|
| in the main menu → [I/F SETUP] → [BATTERY SETTING] |
|
|
|
|
| (page 163) according to the battery in use. |
|
|
|
[EXT DC IN SELECT] | Sets the type of charge level to connect a battery to the <DC IN> terminal. Also |
|
|
| |
| detects a charge level that corresponds to the selected type. |
|
|
| |
| Information about selecting a battery type is the same as [BATTERY SELECT]. |
|
|
| |
| Displays the analog voltage on the viewfinder screen. |
|
|
| |
| [DC PWR SUPPLY], [HYTRON140], [DIONIC90], [ENDURA10], [PAG L96e], |
|
|
| |
| [TYPE A], [TYPE B], [TYPE C] |
|
|
| |
[BATT NEAR END | Selects whether to play the warning sound at battery near end. |
|
|
| |
ALARM] | [ON], [OFF] |
|
|
|
|
[BATT NEAR END | If set to [ON], the warning sound and warning display output can be canceled |
|
|
| |
CANCEL] | when the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch is pushed |
|
|
| |
| towards the <MCK/MCL> side at battery near end. |
|
|
| |
| [ON], [OFF] |
|
|
|
|
[BATT END ALARM] | Sets whether to output the warning sound at battery near end. |
|
|
| |
| [ON], [OFF] |
|
|
|
|
[BATT REMAIN FULL] | Sets the content of the battery remaining charge bar of the display window when a |
|
|
| |
| battery with charge level display function is used. |
|
|
| |
| [70%] | Fully displays at 70%. |
|
|
|
| [100%] | Fully displays at 100%. |
|
|
|
[CARD NEAR END | Sets whether to output the warning sound at P2 card near end. |
|
|
| |
ALARM] | [ON], [OFF] |
|
|
|
|
[CARD NEAR END | Sets remaining time to emit the P2 card near end warning. |
|
|
| |
TIME] | [2min], [3min] |
|
|
|
|
[CARD END ALARM] | Sets whether to output the warning sound at P2 card end. |
|
|
| |
| [ON], [OFF] |
|
|
|
|
[CARD REMAIN/Seg] | Sets the time of one segment (r) for the P2 card remaining capacity bar in the |
|
|
| |
| display window. |
|
|
|
|
| [3min/Seg] | One segment is three minutes |
|
|
|
| [5min/Seg] | One segment is five minutes |
|
|
|
|
|
|
|
| are factory settings. |
|
|
|
|
|
|
[BATTERY SETTING] |
|
|
|
| |
|
|
|
| ||
Item |
| Description of settings | Remark | ||
[BATTERY MODE] | Selects whether to set the near end voltage of a battery. |
|
|
| |
| [AUTO] | Automatically set. |
|
|
|
| [MANUAL] | Manually set. |
|
|
|
[HYTRON140 NEAR | Selects the near end voltage in steps of 0.1 V when the main menu → [I/F |
|
|
| |
END] | SETUP] → [BATTERY/P2CARD] → [BATTERY SELECT] is set to [HYTRON140]. |
|
|
| |
| [12.0V]…[13.1V]…[15.0V] |
|
|
| |
[DIONIC 90 NEAR | Selects the near end voltage in steps of 0.1 V when the main menu → [I/F |
|
|
| |
END] | SETUP] → [BATTERY/P2CARD] → [BATTERY SELECT] is set to [DIONIC90]. |
|
|
| |
| [12.0V]…[13.7V]…[15.0V] |
|
|
| |
|
|
|
|
| are factory settings. |