Deleting a Login | Paradyne 7112 instruction

Security

Deleting a Login

"Procedure

To delete a login record:

1. Follow this menu selection sequence:

Main Menu → Control → Administer Logins

2.Press Ctrl-a to switch to the screen function key area below the dotted line.

3.Select PgUp or PgDn and press Return to page through login pages/records until you find the one to be deleted.

4.Once the correct record is displayed, select Delete and press Enter.

5.To complete the delete action, select Save and press Enter.

When the deletion is complete, Command Complete appears at the bottom of the screen. The number of login pages/records reflects one less record, and the record following the deleted record appears.

Resetting the DSU/CSU's COM Port or Factory Defaults

Misconfiguring the access unit could render the user interface inaccessible, leaving it in a state where a session cannot be started via the COM port or a Telnet session. If this occurs, access unit connectivity can be restored via a directly connected terminal.

Two methods can be used to restore access to the user interface:

Reset COM Port ± Allows you to reset the configuration options related to COM port usage. This also causes a device reset, where the access unit performs a Device Self-Test. No security-related configuration options are changed.

Reload Factory Defaults ± Allows you to reload the Default Factory Configuration, resetting all of the configuration and control settings which causes the current configuration to be destroyed and a device reset. This method is also useful when the user's password(s) have been forgotten.

"Procedure

To reset COM port settings:

1.At the async terminal that is directly connected to the access unit, configure the terminal to operate at 9.6 kbps, using character length of 8 bits, with one stop-bit, and no parity.

2.Reset the access unit, then immediately and repeatedly press Enter at a rate of about 1 press per second until the System Paused screen appears.

3.Tab to the desired method, and enter yes (or y) for the selected prompt.

7112-A2-GB20-20

March 1998

4-3

Image 31

Paradyne 7112 manual Deleting a Login, Resetting the DSU/CSUs COM Port or Factory Defaults

Contents

Model 7112 T1 DSU/CSU Copyright 1998 Paradyne Corporation All rights reserved Contents Configuring the DSU/CSU Monitoring the DSU/CSU Messages and Troubleshooting MIB Descriptions Technical Specifications Glossary Index Document Purpose and Intended Audience About This GuideDocument Summary Product-Related Documents About the T1 DSU/CSU Model 7112 T1 DSU/CSU Features Typical Configuration through a T1 network Typical DSU/CSU Configurations User Interface Types Front Panel LED Status Indicators Network Rear Panel Interface ConnectionsSnmp Management Capabilities Management Information Base MIB Support Accessing the ATI Using the Ascii Terminal Interface ATIConnecting to the Terminal Port Select Initiating an ATI Session Use the screen format Screen Work AreasScreen Format Types What Affects Screen Displays Press Status Test Configuration ControlNavigating Keyboard Keys Procedure Example Switching Between Screen Work AreasScreen Function Keys For the screen Select Press Enter to Function Ending an ATI Session Using the Ascii Terminal Interface ATI Entering Device and System Information Configuring the DSU/CSUMain Menu → Control → Device Configuration Option Areas Configuring the DSU/CSUConfiguration Option Area Configuration Option Set If you select Then Accessing and Displaying Configuration OptionsSaving Configuration Options Main Menu → Configuration Load Configuration From Cross Connect Assignments Assigning DS0 Channels to the Data Port Displaying DS0 Channel Assignments Using the Block or Acami Assignment Method Clearing DS0 Channel Assignments Using the Individual Channel Assignment Method Overview Security Main Menu → Control → Administer Logins Creating a LoginOn the Administer Enter Logins screen, for Resetting the DSU/CSUs COM Port or Factory Defaults Deleting a Login If entering yes to prompt Then ATI Access Effective Access Levels ATI Access to Menu Functions Effective Access Level Assigning Snmp Community Names and Access Levels Controlling Snmp AccessConnection Failed Limiting Snmp Access through the IP Addresses Security IP Addressing IP Addressing Local Addressing Only No FDL IP Addressing ExamplesSubnet NMS a NMS B FDL Connection ± Extending Subnet for FDL LAN a FDL Connection ± Unique FDL Subnet Assigning IP Addresses and Subnet Masks If using Then assign IP Addressing What to Monitor Monitoring the DSU/CSU Main Menu → Status → Display LEDs DSU/CSU LEDs Fail System LEDs Network LEDs SIG ± Network SignalAlarm EER ± Excessive Error Rate Port LEDs System and Test Status Status Screen CommandsMain Menu → Status → System and Test Status Yyyyyyyy Health and Status Messages Xxxxxxxx Self-Test Results Test Status Messages Meaning Test Status Messages Main Menu → Status → Cross Connect Status Cross Connect StatusNetwork Time Slot Fields top Indicate Main Menu → Status → Network Performance Statistics Network Performance Statistics Interval Table Summary Information Worst Interval Hour Totals Ethernet Port StatusMain Menu → Status → Ethernet Port Status Main Menu → Status → Management Protocol Statistics Management Protocol Statistics March Detecting Problems TestingStatus Specific Trap Screen Main Menu → Test Accessing the Test Menu Main Menu → Test → Network Tests Running Network Tests Payload Loopback Line Loopback Repeater Loopback Test Patterns for the Network Remote Send Line Loopback Main Menu → Test → Data Port Tests Running Data Port Tests CSU DSU Data Terminal Loopback Data Channel Loopback Send V.54 Up/Down Sequences Test Patterns for the DTE Send FT1 Up/Down Sequences Ending an Active Test Lamp Test Configuring Snmp Traps Messages and TroubleshootingSnmp Traps Device Messages 1 What Message Indicates What To Do Device Messages Device Messages 2 What Message Indicates What To Do Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting Troubleshooting 2 Symptom Possible Cause Solutions Messages and Troubleshooting Select To Access To Configure Configuration Option Tables Self Test Test TimeoutSystem Options Menu Table A-1. System Options Line Coding Format Network Interface Options MenuTable A-2. Network Interface Options 1 Line Framing Format FDL Management Link Bit Stuffing Possible Settings 62411, Part68, DisableLine Build Out LBO Possible Settings 0.0, ±7.5, ±15, ±22.5 Table A-2. Network Interface Options 2 Network Initiated Line Loopback LLB Table A-2. Network Interface Options 3Network Initiated Payload Loopback PLB Ansi Performance Report Messages Table A-2. Network Interface Options 4Circuit Identifier Synchronous Data Port Assignments Assign By Available Settings Block, ACAMI, ChannelCross Connect Assignments Table A-3. Cross Connect Assignments Invert Transmit Clock Data Port Options MenuTable A-4. Data Port Options 1 Port Base Rate Table A-4. Data Port Options 2 Action on Network Yellow AlarmInvert Transmit and Received Data Table A-4. Data Port Options 3 Ethernet Port Options Menu Port Use Possible Settings 802.3, Version 2, DisableTable A-5. Ethernet Port Options 1 Character Length Terminal Port OptionsTable A-5. Ethernet Port Options 2 Table A-6. Terminal Port Options 1 Stop Bits Login RequiredPort Access Level Possible Settings Level 1, Level 2, Level Table A-6. Terminal Port Options 2 Table A-6. Terminal Port Options 3 Telnet Session OptionsTable A-7. Telnet Session Options 1 Table A-7. Telnet Session Options 2 General Snmp Management Options Snmp MenuTable A-8. General Snmp Management Options 1 Table A-9. Snmp NMS Security Options 1 Name 2 AccessSnmp NMS Security Options Table A-8. General Snmp Management Options 2 Table A-9. Snmp NMS Security Options 2 Access Level Number of Trap Managers Snmp Traps OptionsTable A-10. Snmp Traps Options 1 Snmp Traps Link Trap Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-10. Snmp Traps Options 2 Enterprise Specific Traps Worksheets Configuration WorksheetsConfiguration Option Settings default in Bold Enable, Disable ESF, D4 Disable, EnableBlank Internal, External Nx64, Nx56 Ethernet Port Configuration Option Settings Snmp NMS Security Snmp Worksheets MIB II ± RFC 1213 and RFC MIB Descriptions SysDescr system System GroupSysName system Internet 4 ± Layer Interfaces GroupPhysical 1 ± Layer Datalink/subnetwork EthernetCsmacd6 ± Used for Version Hardware Revision º Up1 IfInErrors ifEntry Testing3 stateIfInOctets ifEntry IfName ifXEntry Extension to Interface Table ifXTableIfXEntry IfStackEntry1 Interface Stack GroupIfStackEntry2 Generic Receive Address Table Interface Test TableIP Group On next InvalidExist. The following objects must Be specified Do not specify the following Icmp GroupTCP Group UDP Group Transmission Snmp GroupTransmission Group Table C-6. Transmission Group Objects Description Dsx1ESF2 ± Indicates DS1 Near End Group Configuration Table ObjectsDsx1ConfigEntry DS1/E1 ± RFC Dsx1SendNoCode1 ± Dsx1SendResetCode4 ±Dsx1B8ZS2 ± Indicates Dsx1AMI5 ± Indicates Dsx1PayloadLoop2 ± Dsx1NoAlarm1 ± NoDsx1LossOfSignal64 ± Dsx1NoLoop1 ± The T1 Dsx1other1 ± Snmp LoopTiming1 ±LocalTiming2 ± ThroughTiming3 ± Dsx1CurrentEntry DS1 Near End Group Current Table Objects Dsx1IntervalEntry DS1 Near End Group Interval Table ObjectsDsx1IntervalEntry10 Dsx1TotalEntry DS1 Near End Group Total Table Objects Number of RS-232-Like Ports Object Ethernet-Like MIB ± RFCRS-232-Like MIB ± RFC DS1 Fractional Group Rs232PortEntry Asynchronous Port Table Objects Disabled2 ± Does notRs232AsyncPortEntry Rs232SyncPortEntry Synchronous Port Table Objects Rs232InSigEntry Input Signal Table Objects Rs232OutSigEntry Output Signal Table Objects TestMon Qrss wellKnownTests Generic Interface Extension MIB ± RFCGeneric Interface Test Table Objects IfExtnsTestEntry ± Starts a Monitor 511 test on the interface NotSupported4 ± Requested InSyncNoBitErrorsInSyncWithBitErrors InProgress3 ± Test is Device Traps, pdn-traps pdn-common Device Configuration Variable pdn-commonEnterprise MIB Object Device Security, pdn-security pdn-common MIB Descriptions Snmp Trap Description Possible Cause Standards Compliance for Snmp TrapsTrap warmStart Trap authentificationFailure Traps linkUp and linkDown Interface LinkUp/Down Variable-Bindings Possible Cause Trap What It Indicates Possible Cause Traps enterpriseSpecificPage Standards Compliance for Snmp Traps Cabling Overview Cables and Pin Assignments Modular RJ48C-to-CA81A T1 Network Interface Cable Modular RJ48C-to-RJ48C T1 Network Interface Cable Use Pin # Terminal Port EIA-232 Connector10BaseT Connector Signal Direction Pin # Pin Serial Crossover Cable Signal DTE V.35 ConnectorDirection Pin Socket Connector Cables and Pin Assignments Model 7112 DSU/CSU Technical Specifications 1 Technical Specifications Model 7112 DSU/CSU Technical Specifications 2 Glossary Channel allocation Configuration optionDefault Digital signal Enterprise-specific Factory defaultsEIA-232 Enterprise MIB Multiplexing ResetLoopback Manager Snmp Subnet address RS-232Self-test Subnet In-8 pattern Yellow AlarmPattern Numbers Index IN-2 IN-3 IN-4