Manuals / Paradyne / Computer Equipment / Network Card

Paradyne 7112 manual Table A-10. Snmp Traps Options 1, Number of Trap Managers

Models: 7112

1 156

Download 156 pages 11.03 Kb

Page 95

Configuration Option Tables

SNMP Traps Options

To access the SNMP Traps Options screen, follow this menu selection sequence:

Main Menu → Configuration → Load Configuration From → Edit →

SNMP & Communication → SNMP Traps

Table A-10. SNMP Traps Options (1 of 2)

SNMP Traps

Possible Settings: Enable, Disable

Default Setting: Disable

Controls the generation of SNMP trap messages. The options for addresses and types of traps are located in this table.

HSNMP Management must be enabled in Table A-8.

Enable ± SNMP trap messages are sent out to SNMP managers.

HIf the destination is the Management port and an external device is attached to the Management port, the messages are sent immediately if there is an active connection. The destination is set with the Trap Manager Destination option.

Disable ± No SNMP trap messages are sent out.

Number of Trap Managers

Possible Settings: 1, 2, 3, 4, 5, 6

Default Setting: 1

Sets the number of SNMP management systems that will receive SNMP traps.

1 to 6 ± Number of trap managers. An NMS IP address is required for each manager.

Trap Manager n IP Address

Possible Settings: 000.000.000.000 ± 255.255.255.255, Clear

Default Setting: 000.000.000.000

Specifies the Internet Protocol address used to identify each SNMP trap manager. n represents the number of the manager (from 1 to 6).

000.000.000.000 ± 255.255.255.255 ± Enter an address for each SNMP trap manager. The range for the first byte is 000 to 255, with the exception of 127. The range for the remaining three bytes is 000 to 255.

Clear ± Clears the IP address and sets to all zeros.

Trap Manager n Destination

Possible Settings: None, Ethernet, FDL

Default Setting: None

Provides the network destination path of each trap manager. n is the number of the manager (from 1 to 6).

None ± No network destination is defined.

Ethernet ± The Ethernet port is the network destination.

FDL ± The Facility Data Link Channel is the default network destination.

HFDL Management Link option must be enabled in Table A-2.

7112-A2-GB20-20

March 1998

A-19

Image 95

Paradyne 7112 manual Table A-10. Snmp Traps Options 1, Number of Trap Managers, Trap Manager n Destination

Contents

Model 7112 T1 DSU/CSU Copyright 1998 Paradyne Corporation All rights reserved Contents Configuring the DSU/CSU Monitoring the DSU/CSU Messages and Troubleshooting MIB Descriptions Technical Specifications Glossary Index Document Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents About the T1 DSU/CSU Model 7112 T1 DSU/CSU FeaturesTypical Configuration through a T1 network Typical DSU/CSU ConfigurationsUser Interface Types Front Panel LED Status IndicatorsNetwork Rear Panel Interface ConnectionsSnmp Management Capabilities Management Information Base MIB SupportConnecting to the Terminal Port Using the Ascii Terminal Interface ATIAccessing the ATI Select Initiating an ATI SessionUse the screen format Screen Work AreasScreen Format Types What Affects Screen DisplaysPress Status Test Configuration ControlNavigating Keyboard KeysProcedure Example Switching Between Screen Work AreasScreen Function Keys For the screen Select Press Enter to FunctionEnding an ATI Session Using the Ascii Terminal Interface ATI Main Menu → Control → Device Configuring the DSU/CSUEntering Device and System Information Configuration Option Area Configuration Option Set Configuring the DSU/CSUConfiguration Option Areas If you select Then Accessing and Displaying Configuration OptionsSaving Configuration Options Main Menu → Configuration Load Configuration FromCross Connect Assignments Assigning DS0 Channels to the Data PortDisplaying DS0 Channel Assignments Using the Block or Acami Assignment MethodClearing DS0 Channel Assignments Using the Individual Channel Assignment MethodOverview SecurityOn the Administer Enter Logins screen, for Creating a LoginMain Menu → Control → Administer Logins Resetting the DSU/CSUs COM Port or Factory Defaults Deleting a LoginIf entering yes to prompt Then ATI AccessEffective Access Levels ATI Access to Menu Functions Effective Access LevelConnection Failed Controlling Snmp AccessAssigning Snmp Community Names and Access Levels Limiting Snmp Access through the IP Addresses Security IP Addressing IP AddressingSubnet IP Addressing ExamplesLocal Addressing Only No FDL NMS a NMS B FDL Connection ± Extending Subnet for FDLLAN a FDL Connection ± Unique FDL SubnetAssigning IP Addresses and Subnet Masks If using Then assignIP Addressing What to Monitor Monitoring the DSU/CSUMain Menu → Status → Display LEDs DSU/CSU LEDsFail System LEDsNetwork LEDs SIG ± Network SignalAlarm EER ± Excessive Error RatePort LEDs Main Menu → Status → System and Test Status Status Screen CommandsSystem and Test Status Yyyyyyyy Health and Status MessagesXxxxxxxx Self-Test ResultsTest Status Messages Meaning Test Status MessagesNetwork Time Slot Fields top Indicate Cross Connect StatusMain Menu → Status → Cross Connect Status Main Menu → Status → Network Performance Statistics Network Performance StatisticsInterval Table Summary InformationWorst Interval Main Menu → Status → Ethernet Port Status Ethernet Port StatusHour Totals Main Menu → Status → Management Protocol Statistics Management Protocol StatisticsMarch Status Specific Trap Screen TestingDetecting Problems Main Menu → Test Accessing the Test MenuMain Menu → Test → Network Tests Running Network TestsPayload Loopback Line LoopbackRepeater Loopback Test Patterns for the Network Remote Send Line LoopbackMain Menu → Test → Data Port Tests Running Data Port TestsCSU DSU Data Terminal LoopbackData Channel Loopback Send V.54 Up/Down Sequences Test Patterns for the DTE Send FT1 Up/Down SequencesEnding an Active Test Lamp TestSnmp Traps Messages and TroubleshootingConfiguring Snmp Traps Device Messages 1 What Message Indicates What To Do Device MessagesDevice Messages 2 What Message Indicates What To Do Troubleshooting 1 Symptom Possible Cause Solutions TroubleshootingTroubleshooting 2 Symptom Possible Cause Solutions Messages and Troubleshooting Select To Access To Configure Configuration Option TablesSelf Test Test TimeoutSystem Options Menu Table A-1. System OptionsLine Coding Format Network Interface Options MenuTable A-2. Network Interface Options 1 Line Framing FormatFDL Management Link Bit Stuffing Possible Settings 62411, Part68, DisableLine Build Out LBO Possible Settings 0.0, ±7.5, ±15, ±22.5 Table A-2. Network Interface Options 2Network Initiated Payload Loopback PLB Table A-2. Network Interface Options 3Network Initiated Line Loopback LLB Circuit Identifier Table A-2. Network Interface Options 4Ansi Performance Report Messages Synchronous Data Port Assignments Assign By Available Settings Block, ACAMI, ChannelCross Connect Assignments Table A-3. Cross Connect AssignmentsInvert Transmit Clock Data Port Options MenuTable A-4. Data Port Options 1 Port Base RateInvert Transmit and Received Data Action on Network Yellow AlarmTable A-4. Data Port Options 2 Table A-4. Data Port Options 3 Table A-5. Ethernet Port Options 1 Port Use Possible Settings 802.3, Version 2, DisableEthernet Port Options Menu Character Length Terminal Port OptionsTable A-5. Ethernet Port Options 2 Table A-6. Terminal Port Options 1Stop Bits Login RequiredPort Access Level Possible Settings Level 1, Level 2, Level Table A-6. Terminal Port Options 2Table A-7. Telnet Session Options 1 Telnet Session OptionsTable A-6. Terminal Port Options 3 Table A-7. Telnet Session Options 2 Table A-8. General Snmp Management Options 1 Snmp MenuGeneral Snmp Management Options Table A-9. Snmp NMS Security Options 1 Name 2 AccessSnmp NMS Security Options Table A-8. General Snmp Management Options 2Table A-9. Snmp NMS Security Options 2 Access LevelNumber of Trap Managers Snmp Traps OptionsTable A-10. Snmp Traps Options 1 Snmp TrapsLink Trap Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-10. Snmp Traps Options 2 Enterprise Specific TrapsWorksheets Configuration WorksheetsConfiguration Option Settings default in Bold Enable, DisableBlank Disable, EnableESF, D4 Internal, External Nx64, Nx56Ethernet Port Configuration Option SettingsSnmp NMS Security SnmpWorksheets MIB II ± RFC 1213 and RFC MIB DescriptionsSysName system System GroupSysDescr system Internet 4 ± Layer Interfaces GroupPhysical 1 ± Layer Datalink/subnetworkEthernetCsmacd6 ± Used for Version Hardware Revision ºUp1 IfInOctets ifEntry Testing3 stateIfInErrors ifEntry IfXEntry Extension to Interface Table ifXTableIfName ifXEntry IfStackEntry2 Interface Stack GroupIfStackEntry1 IP Group Interface Test TableGeneric Receive Address Table On next InvalidExist. The following objects must Be specifiedDo not specify the following Icmp GroupTCP Group UDP GroupTransmission Snmp GroupTransmission Group Table C-6. Transmission Group Objects DescriptionDsx1ESF2 ± Indicates DS1 Near End Group Configuration Table ObjectsDsx1ConfigEntry DS1/E1 ± RFCDsx1SendNoCode1 ± Dsx1SendResetCode4 ±Dsx1B8ZS2 ± Indicates Dsx1AMI5 ± IndicatesDsx1PayloadLoop2 ± Dsx1NoAlarm1 ± NoDsx1LossOfSignal64 ± Dsx1NoLoop1 ± The T1Dsx1other1 ± Snmp LoopTiming1 ±LocalTiming2 ± ThroughTiming3 ±Dsx1CurrentEntry DS1 Near End Group Current Table ObjectsDsx1IntervalEntry10 DS1 Near End Group Interval Table ObjectsDsx1IntervalEntry Dsx1TotalEntry DS1 Near End Group Total Table ObjectsNumber of RS-232-Like Ports Object Ethernet-Like MIB ± RFCRS-232-Like MIB ± RFC DS1 Fractional GroupRs232PortEntry Rs232AsyncPortEntry Disabled2 ± Does notAsynchronous Port Table Objects Rs232SyncPortEntry Synchronous Port Table ObjectsRs232InSigEntry Input Signal Table ObjectsRs232OutSigEntry Output Signal Table ObjectsTestMon Qrss wellKnownTests Generic Interface Extension MIB ± RFCGeneric Interface Test Table Objects IfExtnsTestEntry± Starts a Monitor 511 test on the interface NotSupported4 ± Requested InSyncNoBitErrorsInSyncWithBitErrors InProgress3 ± Test isDevice Traps, pdn-traps pdn-common Device Configuration Variable pdn-commonEnterprise MIB Object Device Security, pdn-security pdn-commonMIB Descriptions Snmp Trap Description Possible Cause Standards Compliance for Snmp TrapsTrap warmStart Trap authentificationFailureTraps linkUp and linkDown Interface LinkUp/Down Variable-Bindings Possible Cause Trap What It Indicates Possible Cause Traps enterpriseSpecificPage Standards Compliance for Snmp Traps Cabling Overview Cables and Pin AssignmentsModular RJ48C-to-CA81A T1 Network Interface Cable Modular RJ48C-to-RJ48C T1 Network Interface CableUse Pin # Terminal Port EIA-232 Connector10BaseT Connector Signal Direction Pin #Pin Serial Crossover CableDirection Pin Socket Connector DTE V.35 ConnectorSignal Cables and Pin Assignments Model 7112 DSU/CSU Technical Specifications 1 Technical SpecificationsModel 7112 DSU/CSU Technical Specifications 2 Glossary Channel allocation Configuration optionDefault Digital signalEnterprise-specific Factory defaultsEIA-232 Enterprise MIBMultiplexing ResetLoopback Manager SnmpSubnet address RS-232Self-test SubnetPattern Yellow AlarmIn-8 pattern Numbers IndexIN-2 IN-3 IN-4