Manuals / Paradyne / Computer Equipment / Network Card

Paradyne 7112 manual Telnet Session Options, Table A-6. Terminal Port Options 3

Models: 7112

1 156

Download 156 pages 11.03 Kb

Page 90

Configuration Option Tables

Table A-6. Terminal Port Options (3 of 3)

Inactivity Timeout

Possible Settings: Enable, Disable

Default Setting: Disable

Provides automatic logoff of an ATI session through the Terminal Port. When the session is closed, User Interface Idle appears on the screen and the unit toggles the Terminal port DSR lead.

Enable ± The ATI session terminates automatically after the Disconnect Time set in the next option. When the session was occurring over an external modem connected to the Terminal port, the modem will interpret the DSR toggle as DTR being dropped and disconnect.

Disable ± An ATI session through the Terminal port will remain active indefinitely.

Disconnect Time (minutes)

Possible Settings: range 1 ± 60

Default Setting: 5

Number of minutes of inactivity before the ATI session terminates automatically.

Timeout is based on no keyboard activity.

H Disconnect Time(minutes) option appears when Inactivity Timeout is enabled.

1 to 60 ± The ATI user session is closed after the selected number of minutes.

Telnet Session Options

To access the Telnet Session Options screen, follow this menu selection sequence:

Main Menu → Configuration → Load Configuration From →

User Interface → Telnet Session

Table A-7. Telnet Session Options (1 of 2)

Telnet Session

Possible Settings: Enable, Disable

Default Setting: Disable

Specifies if the DSU/CSU will respond to a Telnet session request from a Telnet client on an interconnected IP network.

Enable ± Allows Telnet sessions between the unit and a Telnet client.

Disable ± No Telnet sessions allowed.

A-14

March 1998

7112-A2-GB20-10

Image 90

Paradyne 7112 manual Table A-6. Terminal Port Options 3, Table A-7. Telnet Session Options 1

Contents

Model 7112 T1 DSU/CSU Copyright 1998 Paradyne Corporation All rights reserved Contents Configuring the DSU/CSU Monitoring the DSU/CSU Messages and Troubleshooting MIB Descriptions Technical Specifications Glossary Index About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents Model 7112 T1 DSU/CSU Features About the T1 DSU/CSUTypical DSU/CSU Configurations Typical Configuration through a T1 networkFront Panel LED Status Indicators User Interface TypesManagement Information Base MIB Support Rear Panel Interface ConnectionsSnmp Management Capabilities NetworkUsing the Ascii Terminal Interface ATI Accessing the ATIConnecting to the Terminal Port Initiating an ATI Session SelectWhat Affects Screen Displays Screen Work AreasScreen Format Types Use the screen formatKeyboard Keys Status Test Configuration ControlNavigating PressProcedure For the screen Select Press Enter to Function Switching Between Screen Work AreasScreen Function Keys ExampleEnding an ATI Session Using the Ascii Terminal Interface ATI Configuring the DSU/CSU Entering Device and System InformationMain Menu → Control → Device Configuring the DSU/CSU Configuration Option AreasConfiguration Option Area Configuration Option Set Main Menu → Configuration Load Configuration From Accessing and Displaying Configuration OptionsSaving Configuration Options If you select ThenAssigning DS0 Channels to the Data Port Cross Connect AssignmentsUsing the Block or Acami Assignment Method Displaying DS0 Channel AssignmentsUsing the Individual Channel Assignment Method Clearing DS0 Channel AssignmentsSecurity OverviewCreating a Login Main Menu → Control → Administer LoginsOn the Administer Enter Logins screen, for Deleting a Login Resetting the DSU/CSUs COM Port or Factory DefaultsATI Access If entering yes to prompt ThenEffective Access Level Effective Access Levels ATI Access to Menu FunctionsControlling Snmp Access Assigning Snmp Community Names and Access LevelsConnection Failed Limiting Snmp Access through the IP Addresses Security IP Addressing IP AddressingIP Addressing Examples Local Addressing Only No FDLSubnet FDL Connection ± Extending Subnet for FDL NMS a NMS BFDL Connection ± Unique FDL Subnet LAN aIf using Then assign Assigning IP Addresses and Subnet MasksIP Addressing Monitoring the DSU/CSU What to MonitorDSU/CSU LEDs Main Menu → Status → Display LEDsSystem LEDs FailEER ± Excessive Error Rate SIG ± Network SignalAlarm Network LEDsPort LEDs Status Screen Commands System and Test StatusMain Menu → Status → System and Test Status Health and Status Messages YyyyyyyySelf-Test Results XxxxxxxxTest Status Messages Test Status Messages MeaningCross Connect Status Main Menu → Status → Cross Connect StatusNetwork Time Slot Fields top Indicate Network Performance Statistics Main Menu → Status → Network Performance StatisticsSummary Information Interval TableWorst Interval Ethernet Port Status Hour TotalsMain Menu → Status → Ethernet Port Status Management Protocol Statistics Main Menu → Status → Management Protocol StatisticsMarch Testing Detecting ProblemsStatus Specific Trap Screen Accessing the Test Menu Main Menu → TestRunning Network Tests Main Menu → Test → Network TestsLine Loopback Payload LoopbackRepeater Loopback Remote Send Line Loopback Test Patterns for the NetworkRunning Data Port Tests Main Menu → Test → Data Port TestsData Terminal Loopback CSU DSUData Channel Loopback Send V.54 Up/Down Sequences Send FT1 Up/Down Sequences Test Patterns for the DTELamp Test Ending an Active TestMessages and Troubleshooting Configuring Snmp TrapsSnmp Traps Device Messages Device Messages 1 What Message Indicates What To DoDevice Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting 1 Symptom Possible Cause SolutionsTroubleshooting 2 Symptom Possible Cause Solutions Messages and Troubleshooting Configuration Option Tables Select To Access To ConfigureTable A-1. System Options Test TimeoutSystem Options Menu Self TestLine Framing Format Network Interface Options MenuTable A-2. Network Interface Options 1 Line Coding FormatTable A-2. Network Interface Options 2 Bit Stuffing Possible Settings 62411, Part68, DisableLine Build Out LBO Possible Settings 0.0, ±7.5, ±15, ±22.5 FDL Management LinkTable A-2. Network Interface Options 3 Network Initiated Line Loopback LLBNetwork Initiated Payload Loopback PLB Table A-2. Network Interface Options 4 Ansi Performance Report MessagesCircuit Identifier Table A-3. Cross Connect Assignments Assign By Available Settings Block, ACAMI, ChannelCross Connect Assignments Synchronous Data Port AssignmentsPort Base Rate Data Port Options MenuTable A-4. Data Port Options 1 Invert Transmit ClockAction on Network Yellow Alarm Table A-4. Data Port Options 2Invert Transmit and Received Data Table A-4. Data Port Options 3 Port Use Possible Settings 802.3, Version 2, Disable Ethernet Port Options MenuTable A-5. Ethernet Port Options 1 Table A-6. Terminal Port Options 1 Terminal Port OptionsTable A-5. Ethernet Port Options 2 Character LengthTable A-6. Terminal Port Options 2 Login RequiredPort Access Level Possible Settings Level 1, Level 2, Level Stop BitsTelnet Session Options Table A-6. Terminal Port Options 3Table A-7. Telnet Session Options 1 Table A-7. Telnet Session Options 2 Snmp Menu General Snmp Management OptionsTable A-8. General Snmp Management Options 1 Table A-8. General Snmp Management Options 2 Name 2 AccessSnmp NMS Security Options Table A-9. Snmp NMS Security Options 1Access Level Table A-9. Snmp NMS Security Options 2Snmp Traps Snmp Traps OptionsTable A-10. Snmp Traps Options 1 Number of Trap ManagersEnterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, BothTable A-10. Snmp Traps Options 2 Link Trap InterfacesEnable, Disable Configuration WorksheetsConfiguration Option Settings default in Bold WorksheetsDisable, Enable ESF, D4Blank Nx64, Nx56 Internal, ExternalConfiguration Option Settings Ethernet PortSnmp Snmp NMS SecurityWorksheets MIB Descriptions MIB II ± RFC 1213 and RFCSystem Group SysDescr systemSysName system Datalink/subnetwork Interfaces GroupPhysical 1 ± Layer Internet 4 ± LayerVersion Hardware Revision º EthernetCsmacd6 ± Used forUp1 Testing3 state IfInErrors ifEntryIfInOctets ifEntry Extension to Interface Table ifXTable IfName ifXEntryIfXEntry Interface Stack Group IfStackEntry1IfStackEntry2 Interface Test Table Generic Receive Address TableIP Group Be specified InvalidExist. The following objects must On nextUDP Group Icmp GroupTCP Group Do not specify the followingTable C-6. Transmission Group Objects Description Snmp GroupTransmission Group TransmissionDS1/E1 ± RFC DS1 Near End Group Configuration Table ObjectsDsx1ConfigEntry Dsx1ESF2 ± IndicatesDsx1AMI5 ± Indicates Dsx1SendResetCode4 ±Dsx1B8ZS2 ± Indicates Dsx1SendNoCode1 ±Dsx1NoLoop1 ± The T1 Dsx1NoAlarm1 ± NoDsx1LossOfSignal64 ± Dsx1PayloadLoop2 ±ThroughTiming3 ± LoopTiming1 ±LocalTiming2 ± Dsx1other1 ± SnmpDS1 Near End Group Current Table Objects Dsx1CurrentEntryDS1 Near End Group Interval Table Objects Dsx1IntervalEntryDsx1IntervalEntry10 DS1 Near End Group Total Table Objects Dsx1TotalEntryDS1 Fractional Group Ethernet-Like MIB ± RFCRS-232-Like MIB ± RFC Number of RS-232-Like Ports ObjectRs232PortEntry Disabled2 ± Does not Asynchronous Port Table ObjectsRs232AsyncPortEntry Synchronous Port Table Objects Rs232SyncPortEntryInput Signal Table Objects Rs232InSigEntryOutput Signal Table Objects Rs232OutSigEntryIfExtnsTestEntry Generic Interface Extension MIB ± RFCGeneric Interface Test Table Objects TestMon Qrss wellKnownTests± Starts a Monitor 511 test on the interface InProgress3 ± Test is InSyncNoBitErrorsInSyncWithBitErrors NotSupported4 ± RequestedDevice Security, pdn-security pdn-common Device Configuration Variable pdn-commonEnterprise MIB Object Device Traps, pdn-traps pdn-commonMIB Descriptions Trap authentificationFailure Standards Compliance for Snmp TrapsTrap warmStart Snmp Trap Description Possible CauseTraps linkUp and linkDown Interface LinkUp/Down Variable-Bindings Possible Cause Traps enterpriseSpecific Trap What It Indicates Possible CausePage Standards Compliance for Snmp Traps Cables and Pin Assignments Cabling OverviewModular RJ48C-to-RJ48C T1 Network Interface Cable Modular RJ48C-to-CA81A T1 Network Interface CableSignal Direction Pin # Terminal Port EIA-232 Connector10BaseT Connector Use Pin #Serial Crossover Cable PinDTE V.35 Connector SignalDirection Pin Socket Connector Cables and Pin Assignments Technical Specifications Model 7112 DSU/CSU Technical Specifications 1Model 7112 DSU/CSU Technical Specifications 2 Glossary Digital signal Configuration optionDefault Channel allocationEnterprise MIB Factory defaultsEIA-232 Enterprise-specificManager Snmp ResetLoopback MultiplexingSubnet RS-232Self-test Subnet addressYellow Alarm In-8 patternPattern Index NumbersIN-2 IN-3 IN-4