Manuals / Paradyne / Computer Equipment / Network Card

Paradyne 7112 manual Ending an ATI Session

Models: 7112

1 156

Download 156 pages 11.03 Kb

Page 21

Using the ASCII Terminal Interface (ATI)

Ending an ATI Session

Use the Exit function key from any screen to terminate the session.

"Procedure

To end a session with the ASCII terminal interface:

1.Press Ctrl-a to go to the screen function key area below the dotted line.

2.Tab to Exit (or type e or E) and press Enter. The User Interface Idle screen appears.

7112-A2-GB20-20

March 1998

2-7

Image 21

Paradyne 7112 manual Ending an ATI Session

Contents

Model 7112 T1 DSU/CSU Copyright 1998 Paradyne Corporation All rights reserved Contents Configuring the DSU/CSU Monitoring the DSU/CSU Messages and Troubleshooting MIB Descriptions Technical Specifications Glossary Index About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents About the T1 DSU/CSU Model 7112 T1 DSU/CSU FeaturesTypical Configuration through a T1 network Typical DSU/CSU ConfigurationsUser Interface Types Front Panel LED Status IndicatorsSnmp Management Capabilities Rear Panel Interface ConnectionsManagement Information Base MIB Support NetworkUsing the Ascii Terminal Interface ATI Accessing the ATIConnecting to the Terminal Port Select Initiating an ATI SessionScreen Format Types Screen Work AreasWhat Affects Screen Displays Use the screen formatNavigating Status Test Configuration ControlKeyboard Keys PressProcedure Screen Function Keys Switching Between Screen Work AreasFor the screen Select Press Enter to Function ExampleEnding an ATI Session Using the Ascii Terminal Interface ATI Configuring the DSU/CSU Entering Device and System InformationMain Menu → Control → Device Configuring the DSU/CSU Configuration Option AreasConfiguration Option Area Configuration Option Set Saving Configuration Options Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From If you select ThenCross Connect Assignments Assigning DS0 Channels to the Data PortDisplaying DS0 Channel Assignments Using the Block or Acami Assignment MethodClearing DS0 Channel Assignments Using the Individual Channel Assignment MethodOverview SecurityCreating a Login Main Menu → Control → Administer LoginsOn the Administer Enter Logins screen, for Resetting the DSU/CSUs COM Port or Factory Defaults Deleting a LoginIf entering yes to prompt Then ATI AccessEffective Access Levels ATI Access to Menu Functions Effective Access LevelControlling Snmp Access Assigning Snmp Community Names and Access LevelsConnection Failed Limiting Snmp Access through the IP Addresses Security IP Addressing IP AddressingIP Addressing Examples Local Addressing Only No FDLSubnet NMS a NMS B FDL Connection ± Extending Subnet for FDLLAN a FDL Connection ± Unique FDL SubnetAssigning IP Addresses and Subnet Masks If using Then assignIP Addressing What to Monitor Monitoring the DSU/CSUMain Menu → Status → Display LEDs DSU/CSU LEDsFail System LEDsAlarm SIG ± Network SignalEER ± Excessive Error Rate Network LEDsPort LEDs Status Screen Commands System and Test StatusMain Menu → Status → System and Test Status Yyyyyyyy Health and Status MessagesXxxxxxxx Self-Test ResultsTest Status Messages Meaning Test Status MessagesCross Connect Status Main Menu → Status → Cross Connect StatusNetwork Time Slot Fields top Indicate Main Menu → Status → Network Performance Statistics Network Performance StatisticsInterval Table Summary InformationWorst Interval Ethernet Port Status Hour TotalsMain Menu → Status → Ethernet Port Status Main Menu → Status → Management Protocol Statistics Management Protocol StatisticsMarch Testing Detecting ProblemsStatus Specific Trap Screen Main Menu → Test Accessing the Test MenuMain Menu → Test → Network Tests Running Network TestsPayload Loopback Line LoopbackRepeater Loopback Test Patterns for the Network Remote Send Line LoopbackMain Menu → Test → Data Port Tests Running Data Port TestsCSU DSU Data Terminal LoopbackData Channel Loopback Send V.54 Up/Down Sequences Test Patterns for the DTE Send FT1 Up/Down SequencesEnding an Active Test Lamp TestMessages and Troubleshooting Configuring Snmp TrapsSnmp Traps Device Messages 1 What Message Indicates What To Do Device MessagesDevice Messages 2 What Message Indicates What To Do Troubleshooting 1 Symptom Possible Cause Solutions TroubleshootingTroubleshooting 2 Symptom Possible Cause Solutions Messages and Troubleshooting Select To Access To Configure Configuration Option TablesSystem Options Menu Test TimeoutTable A-1. System Options Self TestTable A-2. Network Interface Options 1 Network Interface Options MenuLine Framing Format Line Coding FormatLine Build Out LBO Possible Settings 0.0, ±7.5, ±15, ±22.5 Bit Stuffing Possible Settings 62411, Part68, DisableTable A-2. Network Interface Options 2 FDL Management LinkTable A-2. Network Interface Options 3 Network Initiated Line Loopback LLBNetwork Initiated Payload Loopback PLB Table A-2. Network Interface Options 4 Ansi Performance Report MessagesCircuit Identifier Cross Connect Assignments Assign By Available Settings Block, ACAMI, ChannelTable A-3. Cross Connect Assignments Synchronous Data Port AssignmentsTable A-4. Data Port Options 1 Data Port Options MenuPort Base Rate Invert Transmit ClockAction on Network Yellow Alarm Table A-4. Data Port Options 2Invert Transmit and Received Data Table A-4. Data Port Options 3 Port Use Possible Settings 802.3, Version 2, Disable Ethernet Port Options MenuTable A-5. Ethernet Port Options 1 Table A-5. Ethernet Port Options 2 Terminal Port OptionsTable A-6. Terminal Port Options 1 Character LengthPort Access Level Possible Settings Level 1, Level 2, Level Login RequiredTable A-6. Terminal Port Options 2 Stop BitsTelnet Session Options Table A-6. Terminal Port Options 3Table A-7. Telnet Session Options 1 Table A-7. Telnet Session Options 2 Snmp Menu General Snmp Management OptionsTable A-8. General Snmp Management Options 1 Snmp NMS Security Options Name 2 AccessTable A-8. General Snmp Management Options 2 Table A-9. Snmp NMS Security Options 1Table A-9. Snmp NMS Security Options 2 Access LevelTable A-10. Snmp Traps Options 1 Snmp Traps OptionsSnmp Traps Number of Trap ManagersTable A-10. Snmp Traps Options 2 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps Link Trap InterfacesConfiguration Option Settings default in Bold Configuration WorksheetsEnable, Disable WorksheetsDisable, Enable ESF, D4Blank Internal, External Nx64, Nx56Ethernet Port Configuration Option SettingsSnmp NMS Security SnmpWorksheets MIB II ± RFC 1213 and RFC MIB DescriptionsSystem Group SysDescr systemSysName system Physical 1 ± Layer Interfaces GroupDatalink/subnetwork Internet 4 ± LayerEthernetCsmacd6 ± Used for Version Hardware Revision ºUp1 Testing3 state IfInErrors ifEntryIfInOctets ifEntry Extension to Interface Table ifXTable IfName ifXEntryIfXEntry Interface Stack Group IfStackEntry1IfStackEntry2 Interface Test Table Generic Receive Address TableIP Group Exist. The following objects must InvalidBe specified On nextTCP Group Icmp GroupUDP Group Do not specify the followingTransmission Group Snmp GroupTable C-6. Transmission Group Objects Description TransmissionDsx1ConfigEntry DS1 Near End Group Configuration Table ObjectsDS1/E1 ± RFC Dsx1ESF2 ± IndicatesDsx1B8ZS2 ± Indicates Dsx1SendResetCode4 ±Dsx1AMI5 ± Indicates Dsx1SendNoCode1 ±Dsx1LossOfSignal64 ± Dsx1NoAlarm1 ± NoDsx1NoLoop1 ± The T1 Dsx1PayloadLoop2 ±LocalTiming2 ± LoopTiming1 ±ThroughTiming3 ± Dsx1other1 ± SnmpDsx1CurrentEntry DS1 Near End Group Current Table ObjectsDS1 Near End Group Interval Table Objects Dsx1IntervalEntryDsx1IntervalEntry10 Dsx1TotalEntry DS1 Near End Group Total Table ObjectsRS-232-Like MIB ± RFC Ethernet-Like MIB ± RFCDS1 Fractional Group Number of RS-232-Like Ports ObjectRs232PortEntry Disabled2 ± Does not Asynchronous Port Table ObjectsRs232AsyncPortEntry Rs232SyncPortEntry Synchronous Port Table ObjectsRs232InSigEntry Input Signal Table ObjectsRs232OutSigEntry Output Signal Table ObjectsGeneric Interface Test Table Objects Generic Interface Extension MIB ± RFCIfExtnsTestEntry TestMon Qrss wellKnownTests± Starts a Monitor 511 test on the interface InSyncWithBitErrors InSyncNoBitErrorsInProgress3 ± Test is NotSupported4 ± RequestedEnterprise MIB Object Device Configuration Variable pdn-commonDevice Security, pdn-security pdn-common Device Traps, pdn-traps pdn-commonMIB Descriptions Trap warmStart Standards Compliance for Snmp TrapsTrap authentificationFailure Snmp Trap Description Possible CauseTraps linkUp and linkDown Interface LinkUp/Down Variable-Bindings Possible Cause Trap What It Indicates Possible Cause Traps enterpriseSpecificPage Standards Compliance for Snmp Traps Cabling Overview Cables and Pin AssignmentsModular RJ48C-to-CA81A T1 Network Interface Cable Modular RJ48C-to-RJ48C T1 Network Interface Cable10BaseT Connector Terminal Port EIA-232 ConnectorSignal Direction Pin # Use Pin #Pin Serial Crossover CableDTE V.35 Connector SignalDirection Pin Socket Connector Cables and Pin Assignments Model 7112 DSU/CSU Technical Specifications 1 Technical SpecificationsModel 7112 DSU/CSU Technical Specifications 2 Glossary Default Configuration optionDigital signal Channel allocationEIA-232 Factory defaultsEnterprise MIB Enterprise-specificLoopback ResetManager Snmp MultiplexingSelf-test RS-232Subnet Subnet addressYellow Alarm In-8 patternPattern Numbers IndexIN-2 IN-3 IN-4