Manuals / Polycom / Computer Equipment / Server

Polycom 14117800 manual Configuring Ethernet Link Secondary, Adm. Page Configuration/ETH0/Link

Models: 14117800

1 220

Download 220 pages 4.94 Kb

Page 112

112Configuring KIRK Wireless Server 600v3

5In the IP address field, type the new IP address.

The new IP address is now the default address when accessing the KWS600v3.

6In the Network mask field, type a new network mask.

7In the Default gateway field, type the IP address of the default gateway. Contact your system administrator for more information.

8Click OK.

9Click Reset (under Administration menu) to save your configuration.

7.6.4.3 Configuring Ethernet Link (Secondary)

1Under the Configuration menu, click ETH0, and then click Link.

Figure 53 Adm. Page: Configuration/ETH0/Link page

2From the Link list, select auto, and then click OK.

When selecting auto, the link speed will be determined by the network switch.

3Click Reset (under Administration menu) to save your configuration.

14117800, Ed.2.6

Image 112

Polycom 14117800 manual Configuring Ethernet Link Secondary, Adm. Page Configuration/ETH0/Link

Contents

Part No , Ed.2.6 April 16 Proprietary and Confidential Contents Installing the Kirk Repeater Kirk Handset Registration and Subscription 145 Chapter Configuration/General/Update 189 Configuration of an NTP Server / Client 197 14117800, Ed.2.6 Figures Adm. Page Configuration/ETH0/IP Configuration Tool Alt Master tab Adm. Page Administration/Download/Config Contents Tables 14117800, Ed.2.6 Preface Before You Begin Where is it? What is it about? When to use it? Chapter OverviewRelated Documentation Acronyms IpeiPreface 14117800, Ed.2.6 Introduction This section provides information aboutComponents of the Kirk Wireless Server 600v3 Solution Kirk Wireless ServerWireless Bands Kirk RepeaterKirk Handset Kirk Maintenance Software Auto Login and HandoverKirk SIO Application Interface Requirements for the Kirk Wireless Server 600v3 Solution Kirk Wireless Server Environmental RequirementsIntroduction Electrical Requirements Kirk Repeater Environmental RequirementsKirk Handsets Environmental Requirements Software Requirements Deploying Kirk Wireless Server Deployment of a Kirk Wireless Server 600v3 Multi-Cell Recommendations for KWS600v3/KIRK Repeater PlacementSync over Air Examples of Synchronization Chains Synchronization Chain With One Sync Master Primary Sync Ways Synchronization Chain With Alternative Sync Ways Synchronization Chain with Alternative Sync Ways Synchronization Chain Layout with Alternative Sync Ways Synchronization Chain With and Without Alternative Sync Ways Synchronization Chain With Repeaters Deploying Kirk Wireless Server 14117800, Ed.2.6 Installing the Kirk Wireless Server Description of Kirk Wireless ServerUnpacking Inspect for DamageVariants of Kirk Wireless Server Part Number Kirk Wireless Server 600v3 Types and Part NumbersKirk Wireless Server 600v3 Appearance and Components LED that indicates whether or not the unit is functioning KWS600v3 faceplate includes the following see figure belowKirk Wireless Server 600v3 LED Indicators Front Cover LED Indicator MeaningResetting the Kirk Wireless Server 600v3 Hardware Kirk Wireless Server 600v3 Reset ButtonFaceplate Installing the Kirk Wireless Server Press button ActionKirk Wireless Server 600v3 Indoor Wall Mounting Connect the wire into the RJ45 plug on the KWS600v3Recording the Installation Information Kirk Repeater Description Installing the Kirk RepeaterKirk Repeater provides RF Channels to Kirk Handsets Kirk Repeater Types and Part Numbers Kirk Repeater Business 1.8 GHz, 4 channelsInstalling the Kirk Repeater Kirk Repeater LED IndicatorsKirk Repeater Appearance and Components Installing the Kirk Repeater 3Repeater and External Antenna Installed on the Wall Checking Indicators Powering the Kirk RepeaterPower Options Content of the Kirk Programming Kit RepeaterSet up of the Hardware for Repeater Programming Programming the Kirk Repeater with the ServiceToolBase Station Repeater Installing the Kirk Repeater Installing the Kirk Repeater Installing the Kirk Repeater Installing the Kirk Repeater Installing the Kirk Repeater Installing the Kirk Repeater Numbering of repeaters in a repeater jump configuration Synchronization Ways Use of Kirk Repeater With External AntennaRadio Link Preparing Kirk Handset for Use Kirk Handset DescriptionKirk Handset Types Variants of Kirk HandsetsKirk Charger Types and Part Numbers Variants of Kirk ChargersVariants of Power Supplies Installing BatteryPower Supply Types and Part Numbers Installing Battery on Kirk 4020/KIRK 4040/KIRK 4080 Handsets Installing Battery on Kirk 3040 HandsetsInstalling Battery on Kirk 5020 / 5040 Handsets Remove Back Cover from Handset with Screw FastenerUsing the Charger Charging Kirk HandsetsSingle Charger for 4080 Handset Place the handset in the charger Retrieving the Serial Number of the Kirk Handset Kirk 5020 / 5040 HandsetsRetrieving Serial Number on Kirk 3040 Handsets Retrieving Serial Number on Kirk 5020 / 5040 Handsets Preparing Kirk Handset for Use 14117800, Ed.2.6 Configuring Kirk Wireless Server Powering up the Kirk Wireless ServerPower over Ethernet KWS600v3 supports Power over Ethernet, PoE 802.3afLocal Power Supply Connecting a Computer to the Kirk Wireless ServerChecking Indicators Accessing the Web Based Administration How to Change Internet Protocol Properties using Windows XPLocal Area Connection Properties dialog box Accessing the Kirk Configuration Tool How to Access the AdministrationInstalling the Kirk Configuration Tool Starting the Kirk Configuration ToolConfiguring Single-Cell Solution through Administration Configuration Tool startup windowEntering a System User Name and Password Wireless Server 600v3 Single-cell installationAdm. Page Enter Network Password dialog box Assigning a Specific IP AddressAdm. Page Configuration/ETH0/IP Configuring Ethernet Link Adm. Page Configuration/ETH0/LinkConfiguring Dect System From the Tones list, select a ring toneEnbloc Dialing check box Local R-Key/Display Handling check boxConfiguring Dect Master Adm. Page Configuration/DECT/MasterConfiguring TOS Type of Service Priorities Configuring Dect RadioGK-Id field Configuring Multi-Cell Solution through Administration Under the Configuration menu, click IP0xb8 0x68Configuring the IP Master Primary Kirk Wireless Server Wireless Server 600v3 Multi-cell installationEntering a System User Name and Password Primary Assigning a Specific IP Address PrimaryAdm. Page Configuration/ETH0/DHCP Click either Reset Immediately or Idle Reset Obtaining a Multi-Cell License PrimaryConfiguring Ethernet Link Primary User fields, type the user names0x7f up to128 Configuring Dect System Primary0xff up to Configuring Dect Master Primary Configuring Dect Radio Primary Configuring TOS Type of Service Priorities Primary Configuring Sync Master Assigning a Specific IP Address Sync MasterAdm. Page Configuration/ETH0/DHCP Configuring Ldap Replicator Sync Master Adm. Page Configuration/LDAP/ReplicatorConfiguring Dect Master Sync Master Configuring Dect Radio Sync MasterConfiguring the Alternative Master Kirk Wireless Server Entering a System User Name and Password Standby Assigning a Specific IP Address StandbyAdm. Page Configuration/ETH0/DHCP Configuring Ethernet Link Standby Configuring Dect Master StandbyConfiguring the Secondary Kirk Wireless Server Configuring Dect Radio StandbySelect the Disable check box to disable the radio Click OK WS600v3 Multi-cell installation primary and secondaries Entering a System User Name and Password Secondary Assigning a Specific IP Address Secondary Configuring Ethernet Link Secondary Setting Ldap Replicators Secondary Configuring Dect Master Secondary Configuring Dect System Secondary Configuring Dect Radio Secondary Configuring Secondary KWS600v3 Using a Back-Up File Configuring Standalone Ldap ServerSetting Ldap Mode Ldap Server Configuring Dect Master Ldap Server Select the Disable check box to disable the radioConfiguring Alternative Ldap Server Setting Ldap Mode Alt. Ldap Server Setting Ldap Replicator Alt. Ldap ServerAdm. Page Configuration/LDAP/Replicator Configuration Tool Master tab IP Address area Deselect the Dhcp check boxConfiguring Kirk Wireless Server Gatekeeper area From the Mode list, select Active Configuring the Master Primary Kirk Wireless Server Master tab you configure the Master Primary KWS600v3Configuration Tool Master tab Configuring Kirk Wireless Server Configuring the Alternative Master Kirk Wireless Server Configuration Tool Alt Master tab Configuring Kirk Wireless Server 600v3 Configuring Ldap Server Ldap Server tab you configure the Ldap ServerConfiguration Tool Ldap Server tab Configuring Alternative Ldap Server Configuration Tool Alt Ldap Server tab Configuration Tool Sync Master tab Configuring the Secondary Kirk Wireless Server WS600v3 Multi-cell installation primary and secondaries Secondaries tab you configure the Secondary KWS600v3 IP Address Range areaIP Settings Shared area Configuration Tool Secondary Settings dialog boxUploading Configuration Files Saving ConfigurationsSelect files to upload dialog box appears Configuration Tool Select files to upload dialog box Configuration Tool Upload dialog box Opening Configuration Files Select configuration text files to open dialog box appearsKirk Handset Registration and Subscription Registering Handsets Using Skinny ProtocolRegistering Kirk Handsets Adm. Page Administration/DECT/Users Click New An Edit User dialog box appearsRegistering Handsets Using H.323 Protocol Click New An Edit User dialog box appears Registering Handsets Using SIP Protocol Click New An Edit User dialog box appears Kirk Handset Registration and Subscription Subscribing Kirk Handsets Kirk 3040 HandsetSubscribing Handsets Before subscribing handsets you need to ensureChanging to another System Automatically Using Auto Login a Press Menu go to Menu Login Press 3 go to Select LoginSubscribing a Handset to Different Systems Changing to another System ManuallyKirk 4020/4040/4080 Handset Subscribing Handsets Changing to another System Automatically Using Auto Login B Press 3 go to Select Login Auto aPress 3 go to Select Login Auto B Kirk 5020 / 5040 HandsetCreating Login Subscribing Handset Subscribing a Handset to Different Systems Viewing Handset/User Configuration Kirk Handset ManagementTo unsubscribe a handset Press Menu Press go to Menu Login Searching for Handset/User InformationUnsubscribing Kirk Handsets Kirk 3040/4020/4040/4080 HandsetRemoving Kirk Handsets from the List Deregistering Handset has been unsubscribedChanging User Configurations Click DeleteAdjusting the Kirk Handset Content of the Kirk Programming Kit HandsetChange settings, and then click Apply Click OK Programming Kit Handset Part no for 3040 Handset consistsSet up of the Hardware for Kirk Handset Adjustment Adjusting the Kirk Handset with the ServiceToolChanging System User Name and Password Using the Web Based AdministrationSystem Management Reading System Information On the General/Info page you can read information aboutReading Dect Statistics StatisticsUsers UnknownIP-master Calls Click ShowAdm. Page Administration/DECT/Unknown RadiosMaster Calls Radio CallsHandovers Reading Ldap Server StatusReading Ldap Replicator Statistics This page provides information about the selected serverReading Ethernet Statistics This page provides status information on the interfaceDiagnostics Click Clear if you want to delete all informationLogging Under the Administration menu, click DiagnosticsTracing Config Show Adm. Page Administration/Diagnostics/TracingMaking a Back-Up of the Configuration File PingUpdating the Kirk Wireless Server Under the Administration menu, click DownloadThis section describes how to update the following Click DownloadUnder the Administration menu, click Upload Updating Configuration FileUpdating Firmware Adm. Page Administration/Upload/Firmware Updating Radio FileClick Send file Updating Boot FileClick Browse Resetting Kirk Wireless Server 600v3 Immediately Resetting the Kirk Wireless ServerThere are three ways of resetting the system Resetting Kirk Wireless Server 600v3 When System is Idle Click OK to reset the system immediatelyResetting in Tftp Mode Using the ServiceToolKirk Repeater Programming Adjusting the Kirk Handset Messaging over MSF Description of Different Types of MSF MessagesAdm. Page Configuration/General/Telnet Activating MSF Messages FunctionSending Text Messages Messaging over MSF 14117800, Ed.2.6 Configuration/General/Update NameValue ExampleCurrent Update Serials IntervalConfiguration of the Update Server InstallationConfiguration System RequirementsRunning Maintenance Maintenance CommandsCheck Command Times CommandProt Command Mod cmd UP0 prot url final-command built-serialMod cmd UP0 prot http//192.168.0.10/firm/ip1200.bin ireset Mod cmd UP1 times /allow 12,22,23,0,1,2,3,4Boot Command Bmc command only for Dect devicesScfg Command #bn Rolling backup indexSequence Replaces Example Current date and timeExample Configuration of an NTP Server / Client Example Troubleshooting Solving Problems in Kirk Wireless ServerAdministration Page of the Kirk Wireless Server No Sys-ObjectKirk Configuration Tool for Kirk Wireless Server Problem Action requiredOn all radio units with Should You Need to Report a Problem Kirk Repeater Problem Action requiredNot ring Not possible to turn Subscribe even if System ID has been FoundUsing the Gwload Program Frequently Asked QuestionsQuestion General Answer File Setup area, click IP firmware Kirk WS area, click KWS600v3Click Get File An Open IP firmware file dialog box appearsClick Upload Following dialog box appears Gwload Upload dialog boxRegulatory Notices International Regulatory and Product InformationRelevante krav i direktiv 1999/5/EF SäteteleEnglish Essential requirements and other relevantProvisions of Directive 1999/5/EC Español SpanishSuomi Finnish KWS600V3 Server tyyppinen laite on Explosive Device Proximity Warning Appropriate RF safety/installation Information Important Safety Instructions and Product Information SafetyIntrinsic safety Spare parts and accessories Regulatory Notices Limited Warranty Regulatory Notices Regulatory Notices 14117800, Ed.2.6 Index 14117800, Ed.2.6 Index 14117800, Ed.2.6