Samsung CLP-600 Dynamic Addressing (BO O T P/DH CP), Config uri ng IPX Fra m e Ty pes

Using Your Printer on a Network (CLP-600N only)
8. 3
13 Repeat step 1 2 to co mplete th e address from the 1s t b y te
to the 4th b y te .
14 To select other paramete rs, such as the S ubnet M ask or
Gatewa y, press the scroll button ( or ). Press the
Enter button ( ).
15 Repeat steps 12 through 13 to configure the other TCP/IP
parameters.
16 Press the On Line/Cont inue button ( ) to return to
ready mode.
Dynamic Addressing (BO O T P/DH CP)
To assign the T CP/IP ad dress autom atically by the serv er, tak e
the following steps:
1 In ready mode, press the Menu button ( ) until you see
“Netw o rk” on the bottom line of th e d isplay. Press the
Enter button ( ) to a ccess the menu.
2 Press the Enter button ( ) when “Config Network”
displays o n th e bo tto m line.
3 Press the scroll button ( or ) until “Yes” displays,
and press the
Enter button ( ).
4 Press the Upper Level button ( ), then us e th e scroll
button ( ).
5 Press the Enter button ( ) when “Config TCP” d i splays.
6 Press the scroll button ( or ) until “Yes” displays,
and press the
Enter button ( ).
7 Press the Upper Level button ( ), then us e th e scroll
button ( ).
8 Press the Enter button ( ) when “IP Get Method”
displays.
9 Press the scroll button ( or ) until “DHCP” displays,
and press the
Enter button ( ).
10 To assign the address from the B OOTP serv er, press the
Enter button ( ) whe n “BOOTP” displays .
11 Press the On Line/Cont inue button ( ) to return to
ready mode.
Config uri ng IPX Fra m e Ty pes
On IPX/SPX protocol networks (for example, Novell NetWare),
the format o f th e netw o r k com m u n ica tion frame s must be
specified for the printer. In most cases, you can keep the ‘ Auto’
default setting. However, you can manua lly set the frame type
forma t , if req u ire d .
•
Auto (default): A uto matically senses an d lim its the frame
type to th e first o ne detected .
•
EN_8022 : Limits the frame type to IPX over IEEE 802.2
with IEEE 802.3 frames. All others will be discarded.
• EN_8023 : Limits the frame type to IPX over IEEE 802.3
fram es. All others w i ll be discarded.
•
EN_II : Limits the frame t y pe to IPX over E t her net Frames.
All others will be discarded.
•
EN_SNAP : Limits the fr a m e typ e to IPX ov e r S NAP with
IEEE 802.3 frames. All others will be discarded.
Note that the IPX/S PX protocol must be ena bled in th e
Netware
menu before you can configure frame types. See
“Setting Network Protocols” on page 8.2.
Take th e foll ow in g ste p s to ch ange the fr ame type fo rm at:
1 In ready mode, press the Menu button ( ) until you see
“Netw ork” o n the bottom line of th e d isplay. Press the
Enter button ( ) to access the m e n u.
2 Press the Enter button ( ) when “Config N e two r k ”
displays on the b ottom line.
3 Press the scroll button ( or ) until “Yes” displays on
the bottom line . Press th e
Enter button ( ).
4 Press the Upper Level button ( ).
5 Press the scroll button ( or ) until “Netware”
displays on th e b ottom line. Pr ess the
Enter button ( ).
6 Press the scroll button ( or ) until “On” displays on
the bottom line . Press th e
Enter button ( ).
7 Press the Upper Level button ( ), then use th e scroll
button ( ).
8 Press the Enter button ( ) when “ Co n fig N e tware”
displays.
9 Press the scroll button ( or ) until “Yes” displays on
the bottom line . Press th e
Enter button ( ).
10 Press the Upper Level button ( ), then use th e scroll
button ( ).
11 Press the Enter button ( ) when “IPX Frame Typ e”
displays.