Manuals / Teledyne / Household Appliance / Carbon Monoxide Alarm

Teledyne 300M instruction manual Span Check

Models: 300M

1 123

Page 38

Teledyne API Model 300M CO Analyzer Instruction Manual, 04033, Rev. A

3.1.2 Span Check

Allow the analyzer to sample span gas through the sample port. Press CAL button. After a few minutes the CO reading should be at the expected concentration. If the correct concentration is not reached, then the instrument can be adjusted to read the correct value. To do this, press CONC and enter the expected concentration of the calibration gas. The SPAN button should now be displayed on the front panel. Pressing SPAN and ENTER will modify the internals formulas used to compute the CO reading. If the SPAN button is not displayed, this means that the span reading is too far out of adjustment to do a reliable calibration. The reason for this must be determined before the analyzer can be calibrated. See Section 10.5 for troubleshooting calibration problems.

3-2

Page 38

Image 38

Teledyne 300M instruction manual Span Check

Contents

MODEL 300M CARBON MONOXIDE ANALYZER T-API 6565 NANCY RIDGE DRIVE SAN DIEGO, CATOLL-FREE FAX TEL 04033and in the manner described in this manual SAFETY MESSAGESThe analyzer should only be used for the purpose LIST OF TABLES TABLE OF CONTENTSLIST OF FIGURES VIII5 DIAGNOSTICS 3 PERFORMANCE TESTING4 SETUP MODE 6 HANDLING WARNINGS8 CALIBRATION 9 ADJUSTMENTS10 TROUBLESHOOTING 10-112-1 11 ROUTINE MAINTENANCE12 SPARE PARTS LISTS 232 INTERFACELIST OF FIGURES LIST OF TABLES viii1 INTRODUCTION 1.2 WarrantyWARRANTY POLICY 02024c 1.1 PrefaceTERMS AND CONDITIONS 1.3 Principle of Operation Figure 1-1 Pneumatic Diagram 1.4 Specifications lift and carry the Model 300M 1.5 Installation and OverviewLeak check all fittings with soap solution suitable vent outside the analyzer areaPower plug must have ground lug Page Figure 1-2 Carbon Monoxide Analyzer 1-10 1.6.2 Remote Contact Closures Zero/Span Inputs 1.6.1 Electrical Connections1.6 Electrical and Pneumatic Connections 1.6.3 Status Outputs OptionalTable 1-1 Status Outputs 1.6.4 RS-2321.6.5 Pneumatic System 1-121.6.8 Exhaust Connections 1.6.6 Sample Gas Connection1.6.7 Zero/Span Valve Connections sample gas connectionsFigure 1-4 Rear Panel Pneumatic Connections 1-141.7 Operation Verification 1-15Factory Installed Options Table 1-2 Final Test and Calibration Values1-16 Option Installed1.8.2 Span Valve 1.8 Options1.8.1 Rack Mount With Slides 1-17INTENTIONALLY BLANK 1-182 OPERATION 2.1 Key Features2.1.3 E2ROM Backup Of Software Configuration 2.1.1 CO Readout2.1.5 Data Acquisition DAS 2.1.7 Password ProtectionTable 2-1 Password Levels 2.1.6 RS-232Interface2.2 Front Panel 2.2.1 Front Panel DisplayFigure 2-1 Model 300M Front Panel Meaning Table 2-2 System ModesMode Meaning Table 2-3 Test MeasurementsTest Message 2.2.2 Programmable Push Buttons Table 2-4 Warning Messages2.2.3 Status LED’s Figure 2-2 Illustration of Normal DisplayMeaning Table 2-5 Status LED’sState 2-10 INTENTIONALLY BLANK3.1.1 Zero Check 3 PERFORMANCE TESTING3.1 Manual Zero/Span Check span gas into the analyzer3.1.2 Span Check 3.1.3 Dual Range Calibration 3.2 Span Valve Option 3.3 Zero/Span Valves Option3.4 Automatic Zero/Span Check 5 minutes later than the present time see Section 4.3 and 4.4 for setting present timeThe programmed start time must be a minimum of compute the carbon monoxide readingPage Table 3-1 Calibration Controls least to be established3.9 Hold Off 3.7 Remote Zero/Span Check or Adjustment RS-2323.8 Power-OnHold Off 3-104 SETUP MODE 4.1 Setup Mode Operation4.5 Adjusting the Clock Speed 4.3Setting the Time-of-Day4.4 Setting the Date 4.6.2 Dual Range Mode DUAL 4.6 Setting the CO Concentration Range4.6.1 Single Range Mode SNGL 4.6.3 Auto Range Mode AUTO4.9 Setting the Analyzer I.D 4.7 Setting the Analog Output Offset4.8 Setting the RS-232Baud Rate 4.10 Disabling the Calibration Password4.11 Data Acquisition System DAS 4.11.1 Data Channels4.12 Software Configuration 4.13 Gas Alarms 4.13.1 Summary of Setup FunctionsButton Sequence Table 4-1 Setup FunctionsDefault FunctionButton Sequence Table 4-1 Setup Functions ContinuedDefault Function4-10 INTENTIONALLY BLANK5 DIAGNOSTICS 5.1 Test Measurements5.2 Diagnostic Tests Table 5-1 Diagnostic Teststable continued 5.2.1 Signal I/OTable 5-2 I/O Signals table continued Table 5-2 I/O Signals ContinuedSignal Controltable continued Table 5-2 I/O Signals ContinuedSignal ControlTable 5-2 I/O Signals Continued 5.2.2 Analog Output Test5.2.3 Electric Test 5.3 M300M Internal Variables Table 5-3 M300M VariablesINTENTIONALLY BLANK 6 HANDLING WARNINGS INTENTIONALLY BLANK Table 7-1 RS-232Port Setup - Front Panel 7 RS-232COMMUNICATIONS7.1 DAS Reporting Table 7-2 RS-232Message TypesPage 7.2 Warnings Warning Message Cleared Table 7-3 RS-232Warning Message Clear CommandsCommand 7.3 Status/Control Table 7-4 Status ReportsTable 7-5 Control Commands when the analyzer is in the sample modeTable 7-7 Diagnostic Reports 7.4 DiagnosticsTable 7-6 Diagnostic Commands the analyzer is in sample mode7.5 Test Measurements Command Table 7-8 Test Measurement Request Commands7-10 Test Measurement7.6 Viewing and Modifying Variables 7-11Table 7-9 RS-232Variable Names 7-128 CALIBRATION 8.1 Required Equipment and Gas StandardsFigure 8-1 Gas Generation System Figure 8-2 Inlet Venting Recommendations8.2 Multi-PointCalibration Qv × L = Qa × D8.2.1Procedure Page Page 8.3 Zero/Span Checking INTENTIONALLY BLANK 9.1.1 Box Temperature Limits 9 ADJUSTMENTS9.1 Power Supply Board Adjustment Figure 9-1:M300M Electrical Block Diagram 9.2 A/D - D/A Calibration Procedure the value on the voltmeter will remain constantPage 9.4 Output Voltage Range Changes 9.3 Dark Current Signal Adjust ProcedureTo adjust analog recorder offset, see Section 9.5 Flow Readout Adjustment 9.6 DC Power Supply 9.7 CPUINTENTIONALLY BLANK 10-1 10 TROUBLESHOOTING10.1 Overview 10.2.1 Checking the Power Sub-Systems 10-210.2.3Checking the Keyboard 10.3 Troubleshooting Using Warning Messages10.2.2 Checking the CPU and Display 10-3Warning Message Table 10-1 Warning Messages10-4 Meaning10.4 Troubleshooting Using Test Function Values 10-5Test Function Table 10-2 Test Function Values10-6 Meaning10.5.2Noisy, Unstable, or Non-LinearSpan Readings 10.5 Troubleshooting Dynamic Problems10.5.1Noisy or Unstable Readings at Zero 10.5.3Slow Response to Changes in Concentration10.5.6Cannot Span or Cannot Dynamic Span 10.6.1 Troubleshooting Flow Problems10.5.5Cannot Zero or Cannot Dynamic Zero 10-8Low Flow Hazardous voltages present - use cautionFlow is zero High FlowOptical Bench Temperature 10.6.2 Troubleshooting Temperature ProblemsSample Temperature Gas Filter Wheel TemperatureHazardous voltages present - use caution 10.6.3 Checking the V/F Card10-11 Table 10-3 V/F Board Jumpers - Factory Settings 10-1210-13 10.6.3.1 Analog Inputs10.6.3.2 Digital to Analog Converters 10-14 10.6.4 Checking the DC Power Supply Board10.6.3.3 Digital I/O Lines 10.6.5 Checking the Synchronous Demodulator Board 10-15Figure 10-2 Detector Waveform 10.6.6 Checking the Opto InterrupterFigure 10-1 Opto Pickup Waveform 10-1610.6.7 Flow/Pressure Sensor 10-1710.7 Warranty/Repair Questionnaire 10-18Table 11-1 Maintenance Schedule 11 ROUTINE MAINTENANCE11.1 Model 300M Maintenance Schedule 11-111.3Leak Checking 11.2Replacement of Sample Filter11.3.1 Using a Leak Checker Do not exceed 15 PSI of pressurevacuum. This may cause damage to the analyzer the solution may enter and contaminate the cell11.3.2 Leak Self Test Use only bubbles, not liquid11-4 INTENTIONALLY BLANK12-1 12 SPARE PARTS LISTS12.1 Spare parts for CE Mark units Includes 12.2 Model 300M Expendables kit12.3 Model 300M Spare parts kit for one unit 12-2Includes 12.4 Model 300M Level 1 parts kit for ten units12-3 Cables & Adapters come in 4 general types ConnectorsSignal 12-4Wiring 12-512-6 Troubleshooting the modem connectionENABLE MODEM TRANSMISSION Title APPENDIX B Electrical drawing indexDrawing Number 12-7