Centronics / Centro, 4.1 ACK/BUSY, ・ TYPE1 ・ TYPE2 | Toshiba B-EX4

5.SYSTEM MODE

5.9.4Centronics / CENTRO.

EO18-33027

5.9 IP ADDRESS SETTING

Menu list of Centoronics / CENTRO.

MENU ITEM

System Mode / SYSTEM MODE <7>INTERFACE SETTING / <7>INTERFACE

Centronics / CENTRO.

ACK/BUSY

Input prime / INPUT PRIME

Plug and play / PLUG & PLAY

5.9.4.1 ACK/BUSY

・TYPE1

・TYPE2

5.9.4.2 Input prime / INPUT PRIME

・Disable / OFF

・Enable / ON

5.9.4.3 Plug and play / PLUG & PLAY

・Disable / OFF

・Enable / ON

(*)Plug & play function of USB is always enabled regardless of this setting.

Display pattern and key operation

Scroll display

5-71

Image 119

Toshiba B-EX4 Centronics / Centro, 4.1 ACK/BUSY, ・ TYPE1 ・ TYPE2, Input prime / Input Prime, Plug and play / Plug & Play

Contents

EX4 Series Table of Contents System Mode EO18-33027 Rfid Analyze Tool Periodic Maintenance Procedure11-1 EO18-33027 Unpacking Procedure Open Printer Installation Maintenance Printer Block Screw OPENING/CLOSING the Printer Block OPENING/CLOSING the TOP CoverRemoving the Side Panel L Raise the print head block until it stops Hooks Removing the Operation Panel Operation Panel Ass’y Operation Panel Harness Installation Procedure for Optional Equipment Hooker Disc Cutter B-EX204-QM-R Main PC Board CN15 Disc cutter PC Board Cutter Harness Disassemble the frame into 3 parts Rotary Cutter B-EX204-R-QM-RDescription ’ty/Unit Cutter Unit SMW-4x8 Determine the position by fitting the two parts here Do not 4x8 Screw Harness Ass’y CN7 9 pins CN15 9 pins Cutter Unit SM-4 x 8 Screw Notch Installation Procedure for Optional Equipment Peel OFF Module B-EX904-H-QM-R Hook Turn the power off and disconnect the power cord Installation Procedure for Optional Equipment CN4 Selection Switch TBD Bush Cut Strip Sensor Harness Adjustment Ribbon Saving Module B-EX904-R-QM-R Plunger Head Up Arm Spacer Solenoid SM-4x8 Screw Frame CN2 RTC/USB host I/F card 1 pc Installation ProcedureRTC/USB Host I/F Card B-EX700-RTC-QM-R Remove the Blind Plate C from the back Packing List Expansion I/O Interface Board B-EX700-IO-QM-R Remove the Blind Plate D from the back Installation Procedure for Optional Equipment Wireless LAN Board B-EX700-WLAN-QM-R Installation Procedure Installation Procedure for Optional Equipment Parallel Interface card B-EX700-CEN-QM-R Remove the Blind Plate a from the back Re-attach the Side Panel L to the printer Operation Panel System Mode Overview Menu Item SELF-DIAGNOSTIC TestDIAG. menu item list Menu operation procedure example Counter Paramete Print Contents CUT FEED1 ～ FEED4Print PRINT1 ～ PRINT4 Adjust Parameter Settings LATIN9 EX.I/O ModeReflect Font Maxi Code Spec CommandPower Save Time LBL/RBN END RS-232C PanelStorage Area USB LAN/WLAN Centro Socket Port Wlan ModeAES Tkip WPA Mode Default KEY Rfid RTC Auto Diagnostics/AUTO Diagnostics Kanji None ：0000 Print conditionProgram B-EX4T1-G Sdram 32MB Eeprom 256B Head Rank SENSOR2 EXP.I/O NG Expansion I/O check contentsInternal serial I/F check contents EX.232C NG EU, SX704-RFID-U2-R SX704-RFID-U2-US-RUS, AU, TW US, AU, KR2, TW SX704-RFID-U2-EU-R Basic S None USB Memory NGBasic M None Head broken dot check/HEAD Check 1Printer setting / Printer SET Parameter Setting„ Outline of Parameter Setting LCD Display Setting / Panel Standby action / FW/BK ACT Setting for forward feed standby / Forward WaitMedia loading / Media Load Forward feed standby position / Forward Wait POS Standard speed/ STD 3ips Low speed / LOW 2ips Ribbon save / RBN SavePre peel-off / PRE Peel OFF Back feed / Back Speed ESC LF NUL / Manual Soft control setting / Software SETMenu list Soft control setting / Software SET ・ ESC, LF, NUL / ESC,LF,NUL Character code / Font Code・ LATIN9 Control code / Code Feed Key Function Manual selection / Manual・ CODE1 ・ CODE2 ・ CODE3 Peel-off wait status / Peel OFF Status WEB Printer / WEB Printer CharacterEuro code / Euro Code Auto head broken check / Auto HD CHK TYPE1： External I/O mode / EX.I/ORibbon near end / RBN Near END Paper / ribbon end / LBL/RBN END 2.16 XML MaxiCode specification / Maxi Code・ Disable / OFF ・ Standard / STD ・ Oracle / Oracle Compatible with the current version Print method / Energy Type Power save time / PW Save TimeThreshold selection / Threshold Select Print page / Print LCD LanguageLanguage of LCD display / LCD Language Machine name / Machine Name Digit Hex Non Decimal Contrast adjustment / ContrastPassword setting / Password Menu list of Password setting / Password System Mode „ Outline of Printer Parameter Fine Adjustment Fine adjustment value setting/ Adjust SET Digit 50.0 Feed / Feed ADJMax Min Step Display Sign Integer Decimal Fullfil Cut position / CUT ADJ +3.0mm Cut position Paper feed direction Cut position Head position （ｂ）Operation example Issue count 2, Cut interval = System Mode Strip position fine adjustment 0ｍｍ +3.0mm Back feed / Back ADJ Digit Decimal Exist Non Step Direction position / X AdjustDigit 99.5 Decimal Exist Non Density fine tune Thermal transfer / Tone ADJ.TRANS Exist Non Step Ribbon Rewinder / RBN ADJ.FWRibbon Feeder / RBN ADJ.BK Transmissive sensor fine tune / Threshold Trans Refrective sensor fine tune / Threshold Refl +10step EX4T1-G EX4T1-T Speed It sets printing condition of printer for test print Print condition setting / Print ConditionIssue count / Issue Count Test Print Print method / Print Type Issue type / Issue TypePrint speed / Print Speed Sensor / Sensor Type Issue CountPrint Speed Sensor 3 3-dot slant line print / Slant LINE3DOT 2 1-dot slant line print / Slant LINE1DOT Character print / Characters Barcode print / Barcode Auto print Transmissive / Auto Print Trans Factory test / Factory Test Auto print Reflective / Auto Print Refl Reflective sensor / Reflect Sensor Adjustment„ Outline of the Sensor Adjustment Temperature sensor/ Temperature Ribbon end / Ribbon Transmissive / TransPaper empty level / PE REFL./TRANS This is a selection to prevent wrong user operation RAM Clear„ Outline of RAM Clear No RAM clear / no RAM Clear MODE1 HU CUT/RWD TYPE1 XML STD USB Status Ribbon Back tension Parameter setting/Password settingPrint density Direct Thermal Ribbon Rewind XON+READY Auto Auto SnmpINFRA/OPEN Wepoff None Even ACK/BYSY TYPE1 User mode Auto paper measurement Function Enable/Disable RTC setting Network / Network Menu list of Network / Network Menu Item IP Address SettingWire/Wireless LAN selection / LAN/WLAN USB Standard Network setting / SettingWlan Power Save Wins Information Socket port / Socket Port Basic information / Basic InformationGateway / Gateway Address Subnet mask / Subnet Mask ・ 11b/g ・ 11g Wireless LAN standard / Wlan StandardWireless LAN connection mode / Wlan Mode 1.3.14 802.11b transfer rate / 802.11b Baud WEP default Key / Default KEYWlan power save / Wlan Power Save 1.3.13 802.11b channel / 802.11b Channel 2 USB WinsWins Address / Wins Address 1.3.20 LPR Stop bit / Stop BIT 3 RS-232CBaud rate / Speed Data length / Data Length Input prime / Input Prime Centronics / Centro4.1 ACK/BUSY ・ TYPE1 ・ TYPE2 „ Outline of Basic Setting Basic Setting „ Outline of the Rfid Module Setting Rfid Module Setting ID Read / ID Read Test / Test SX704-RFID-U2-CN-R SX704-RFID-U2 TAG IDModule / Module Module type / Module Type 11.2.3Tag type / TAG Country / Country ・ 2CH ・ 3CH ・ 4CH ・ 5CH ・ 6CH ・ 7CH ・ 8CH 11.3.1Position adjustment for re-issue / ADJ Retry PositionRF channel / RF Channel ・ Auto 11.3.3Read retry / Read Retry 11.3.2Issue retry label / Issue Retry LablesDigit 255 Decimal Non SX704-RFID-U2-EU-R/US-R /CN-R UHF setting / UHF Setting11.4.1Output level / Power Level 11.3.4Write retry / Write Retry 11.4.3AGC threshold / AGC Threshold 11.4.2Q value / Q Value 11.4.4Write AGC threshold / Write AGC Threshold 11.4.5Write retry minimum AGC / Write Retry MIN AGC Write data if access pass word matches to password setting 11.5.1Tag test setting / TAG CheckOnaccess Password LCD Display example English 11.5.2Multi word write / Mult Write11.5.3Carrier sense / Carrier Sense „ Key function For the following, refer to the parameter setting sectionCut issue mode when the disk cutter is used „ LED function Down „ Error messagesCancel Enter No Ribbon OFF Blinking Symbols in the message„ LCD message and LED indication Head Error Dhcp Client （Ex ） ESCT20G30LFNUL （Ex ） ESCPC0010A00,0300,2,2,A,00,BLFNULＬＣＤ Display Move to 3. Paper Threshold SettingThreshold Setting Operation Example （English） Depressing Pause Sensor type Judgement Judgment display On Line Mode Online Mode LCD Display Example （English） Online Mode LCD Display Icon Online Mode Display TRANSITION, Operation example （English） Help message for paper empty *1 Help Display Help Display TRANSITION, Operation EXAMPLE（English） Online mode Error content Periodic Maintenance Procedure Remove paper debris or label glue from the media path 50 km When the Strip Module is used Troubleshooting Troubleshooting System Requirement Rfid Analyze Tool V1.5 Set upSetup Disk Installation Setup Disk consists of one CD-ROM Main Menu Application Functions File Menu EO18-33027 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF Test Option Sheet Setting Makes settings for the media to be used Select the printer model Select the test mode This menu is not available Displays Printer Version and Rfid Module Version Example Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF Rfid Analyze Tool Tag Data Rfid Analyze Tool Write/Read Results Box When U2 is selected Write/Read Results Box