Maintenance | Toshiba B-EX4 manual

3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT	EO18-33027
/MAINTENANCE

3.NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT/MAINTENANCE

3.NOTE FOR OPTIONAL EQUIPMENT INSTALLATION /MAJOR UNIT REPLACEMENT/MAINTENANCE

WARNING!

1. Turn the power off and disconnect the power cord before replacing the main parts.

Power Switch

Power Cord

2.Never perform disassembling, assembling, and cleaning just after printing. Doing so may cause you to be injured by the print head and the inner parts of the printer being hot.

3.When cleaning the cutter, be careful not to be injured by the cutter blade.

4.Be careful not to pinch your fingers or hands with the covers.

CAUTION!

1.Fix the harnesses and the cord bushes with the cable clamp. Failure to do this may cause the covers to catch them.

Sensor Harness	Cable Clamp

Cable Clamp	Stepping Motor Cable

Cord Bush

Operation Panel	Print Head Harness
Harness

continued

3-1

Image 10

Toshiba B-EX4 manual Maintenance

Contents

EX4 Series Table of Contents System Mode EO18-33027 11-1 Periodic Maintenance ProcedureRfid Analyze Tool EO18-33027 Procedure Unpacking Open Printer Installation Maintenance Printer Block Screw Removing the Side Panel L OPENING/CLOSING the TOP CoverOPENING/CLOSING the Printer Block Raise the print head block until it stops Removing the Operation Panel Hooks Operation Panel Ass’y Operation Panel Harness Installation Procedure for Optional Equipment Disc Cutter B-EX204-QM-R Hooker Main PC Board CN15 Disc cutter PC Board Cutter Harness Description ’ty/Unit Cutter Unit Rotary Cutter B-EX204-R-QM-RDisassemble the frame into 3 parts SMW-4x8 Determine the position by fitting the two parts here Do not 4x8 Screw Harness Ass’y CN7 9 pins CN15 9 pins Cutter Unit SM-4 x 8 Screw Notch Installation Procedure for Optional Equipment Peel OFF Module B-EX904-H-QM-R Turn the power off and disconnect the power cord Hook Installation Procedure for Optional Equipment CN4 Selection Switch TBD Bush Cut Strip Sensor Harness Adjustment Ribbon Saving Module B-EX904-R-QM-R Plunger Head Up Arm Spacer Solenoid SM-4x8 Screw Frame CN2 RTC/USB Host I/F Card B-EX700-RTC-QM-R Installation ProcedureRTC/USB host I/F card 1 pc Remove the Blind Plate C from the back Expansion I/O Interface Board B-EX700-IO-QM-R Packing List Remove the Blind Plate D from the back Installation Procedure for Optional Equipment Wireless LAN Board B-EX700-WLAN-QM-R Installation Procedure Installation Procedure for Optional Equipment Parallel Interface card B-EX700-CEN-QM-R Remove the Blind Plate a from the back Re-attach the Side Panel L to the printer System Mode Operation Panel Overview DIAG. menu item list SELF-DIAGNOSTIC TestMenu Item Menu operation procedure example Counter Paramete Print Contents PRINT1 ～ PRINT4 FEED1 ～ FEED4Print CUT Adjust Parameter Settings Font EX.I/O ModeReflect LATIN9 LBL/RBN END CommandPower Save Time Maxi Code Spec USB PanelStorage Area RS-232C Centro LAN/WLAN Default KEY Wlan ModeAES Tkip WPA Mode Socket Port Rfid RTC Auto Diagnostics/AUTO Diagnostics Program B-EX4T1-G Print conditionKanji None ：0000 Eeprom 256B Sdram 32MB SENSOR2 Head Rank Internal serial I/F check contents EX.232C NG Expansion I/O check contentsEXP.I/O NG US, AU, KR2, TW SX704-RFID-U2-EU-R SX704-RFID-U2-US-RUS, AU, TW EU, SX704-RFID-U2-R Basic M None USB Memory NGBasic S None Head broken dot check/HEAD Check LCD Display Setting / Panel Parameter Setting„ Outline of Parameter Setting 1Printer setting / Printer SET Forward feed standby position / Forward Wait POS Setting for forward feed standby / Forward WaitMedia loading / Media Load Standby action / FW/BK ACT Back feed / Back Speed Ribbon save / RBN SavePre peel-off / PRE Peel OFF Standard speed/ STD 3ips Low speed / LOW 2ips Menu list Soft control setting / Software SET Soft control setting / Software SETESC LF NUL / Manual Control code / Code Character code / Font Code・ LATIN9 ・ ESC, LF, NUL / ESC,LF,NUL Peel-off wait status / Peel OFF Status Manual selection / Manual・ CODE1 ・ CODE2 ・ CODE3 Feed Key Function Auto head broken check / Auto HD CHK CharacterEuro code / Euro Code WEB Printer / WEB Printer Paper / ribbon end / LBL/RBN END External I/O mode / EX.I/ORibbon near end / RBN Near END TYPE1： Compatible with the current version MaxiCode specification / Maxi Code・ Disable / OFF ・ Standard / STD ・ Oracle / Oracle 2.16 XML Threshold selection / Threshold Select Power save time / PW Save TimePrint method / Energy Type Machine name / Machine Name LCD LanguageLanguage of LCD display / LCD Language Print page / Print Menu list of Password setting / Password Contrast adjustment / ContrastPassword setting / Password Digit Hex Non Decimal System Mode Fine adjustment value setting/ Adjust SET „ Outline of Printer Parameter Fine Adjustment Cut position / CUT ADJ Feed / Feed ADJMax Min Step Display Sign Integer Decimal Fullfil Digit 50.0 +3.0mm Cut position Paper feed direction （ｂ）Operation example Issue count 2, Cut interval = Cut position Head position System Mode Strip position fine adjustment 0ｍｍ +3.0mm Back feed / Back ADJ Density fine tune Thermal transfer / Tone ADJ.TRANS Direction position / X AdjustDigit 99.5 Decimal Exist Non Digit Decimal Exist Non Step Ribbon Feeder / RBN ADJ.BK Ribbon Rewinder / RBN ADJ.FWExist Non Step Refrective sensor fine tune / Threshold Refl Transmissive sensor fine tune / Threshold Trans EX4T1-G EX4T1-T Speed +10step Test Print Print condition setting / Print ConditionIssue count / Issue Count It sets printing condition of printer for test print Sensor / Sensor Issue type / Issue TypePrint speed / Print Speed Print method / Print Type Sensor Issue CountPrint Speed Type 2 1-dot slant line print / Slant LINE1DOT 3 3-dot slant line print / Slant LINE3DOT Character print / Characters Barcode print / Barcode Factory test / Factory Test Auto print Transmissive / Auto Print Trans Auto print Reflective / Auto Print Refl Temperature sensor/ Temperature Sensor Adjustment„ Outline of the Sensor Adjustment Reflective sensor / Reflect Paper empty level / PE REFL./TRANS Transmissive / TransRibbon end / Ribbon No RAM clear / no RAM Clear RAM Clear„ Outline of RAM Clear This is a selection to prevent wrong user operation MODE1 HU CUT/RWD USB Status TYPE1 XML STD Ribbon Rewind Parameter setting/Password settingPrint density Direct Thermal Ribbon Back tension None Even Auto SnmpINFRA/OPEN Wepoff XON+READY Auto ACK/BYSY TYPE1 RTC setting User mode Auto paper measurement Function Enable/Disable USB IP Address SettingWire/Wireless LAN selection / LAN/WLAN Network / Network Menu list of Network / Network Menu Item Information Network setting / SettingWlan Power Save Wins Standard Subnet mask / Subnet Mask Basic information / Basic InformationGateway / Gateway Address Socket port / Socket Port Wireless LAN connection mode / Wlan Mode Wireless LAN standard / Wlan Standard・ 11b/g ・ 11g 1.3.13 802.11b channel / 802.11b Channel WEP default Key / Default KEYWlan power save / Wlan Power Save 1.3.14 802.11b transfer rate / 802.11b Baud 1.3.20 LPR WinsWins Address / Wins Address 2 USB Data length / Data Length 3 RS-232CBaud rate / Speed Stop bit / Stop BIT ・ TYPE1 ・ TYPE2 Centronics / Centro4.1 ACK/BUSY Input prime / Input Prime Basic Setting „ Outline of Basic Setting Rfid Module Setting „ Outline of the Rfid Module Setting Test / Test ID Read / ID Read Module type / Module Type SX704-RFID-U2 TAG IDModule / Module SX704-RFID-U2-CN-R Country / Country 11.2.3Tag type / TAG ・ Auto 11.3.1Position adjustment for re-issue / ADJ Retry PositionRF channel / RF Channel ・ 2CH ・ 3CH ・ 4CH ・ 5CH ・ 6CH ・ 7CH ・ 8CH Digit 255 Decimal Non 11.3.2Issue retry label / Issue Retry Lables11.3.3Read retry / Read Retry 11.3.4Write retry / Write Retry UHF setting / UHF Setting11.4.1Output level / Power Level SX704-RFID-U2-EU-R/US-R /CN-R 11.4.2Q value / Q Value 11.4.3AGC threshold / AGC Threshold 11.4.4Write AGC threshold / Write AGC Threshold 11.4.5Write retry minimum AGC / Write Retry MIN AGC Password 11.5.1Tag test setting / TAG CheckOnaccess Write data if access pass word matches to password setting 11.5.3Carrier sense / Carrier Sense 11.5.2Multi word write / Mult WriteLCD Display example English „ LED function For the following, refer to the parameter setting sectionCut issue mode when the disk cutter is used „ Key function Enter „ Error messagesCancel Down No Ribbon „ LCD message and LED indication Symbols in the messageOFF Blinking Head Error Dhcp Client ＬＣＤ Display （Ex ） ESCPC0010A00,0300,2,2,A,00,BLFNUL（Ex ） ESCT20G30LFNUL Depressing Pause Threshold SettingThreshold Setting Operation Example （English） Move to 3. Paper Judgment display Sensor type Judgement On Line Mode Online Mode LCD Display Online Mode LCD Display Example （English） Icon Online Mode Display TRANSITION, Operation example （English） Help Display Help message for paper empty *1 Online mode Error content Help Display TRANSITION, Operation EXAMPLE（English） Periodic Maintenance Procedure Remove paper debris or label glue from the media path 50 km When the Strip Module is used Troubleshooting Troubleshooting Rfid Analyze Tool System Requirement Setup Disk Installation Setup Disk consists of one CD-ROM Set upV1.5 Application Functions Main Menu File Menu EO18-33027 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF Test Option Sheet Setting Makes settings for the media to be used Select the test mode This menu is not available Select the printer model Example Displays Printer Version and Rfid Module Version Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF Rfid Analyze Tool Tag Data Rfid Analyze Tool Write/Read Results Box When U2 is selected Write/Read Results Box