Write/Read Results Box | Toshiba B-EX4 specs

11. RFID ANALYZE TOOL

EO18-33027

11.4 Operating Procedure

Example (U1 module)

Write Test button

Read Test button

Results box

All read or write test results

Text box

Status bar

Status Data

Write/Read Results Box

Feed amount Total number of succeeded tests

Tag ID

Total number of tests

11- 20

Image 173

Toshiba B-EX4 manual Write/Read Results Box

Contents

EX4 Series Table of Contents System Mode EO18-33027 Rfid Analyze Tool Periodic Maintenance Procedure11-1 EO18-33027 Unpacking Procedure Open Printer Installation Maintenance Printer Block Screw OPENING/CLOSING the Printer Block OPENING/CLOSING the TOP CoverRemoving the Side Panel L Raise the print head block until it stops Hooks Removing the Operation Panel Operation Panel Ass’y Operation Panel Harness Installation Procedure for Optional Equipment Hooker Disc Cutter B-EX204-QM-R Main PC Board CN15 Disc cutter PC Board Cutter Harness Disassemble the frame into 3 parts Rotary Cutter B-EX204-R-QM-RDescription ’ty/Unit Cutter Unit SMW-4x8 Determine the position by fitting the two parts here Do not 4x8 Screw Harness Ass’y CN7 9 pins CN15 9 pins Cutter Unit SM-4 x 8 Screw Notch Installation Procedure for Optional Equipment Peel OFF Module B-EX904-H-QM-R Hook Turn the power off and disconnect the power cord Installation Procedure for Optional Equipment CN4 Selection Switch TBD Bush Cut Strip Sensor Harness Adjustment Ribbon Saving Module B-EX904-R-QM-R Plunger Head Up Arm Spacer Solenoid SM-4x8 Screw Frame CN2 RTC/USB host I/F card 1 pc Installation ProcedureRTC/USB Host I/F Card B-EX700-RTC-QM-R Remove the Blind Plate C from the back Packing List Expansion I/O Interface Board B-EX700-IO-QM-R Remove the Blind Plate D from the back Installation Procedure for Optional Equipment Wireless LAN Board B-EX700-WLAN-QM-R Installation Procedure Installation Procedure for Optional Equipment Parallel Interface card B-EX700-CEN-QM-R Remove the Blind Plate a from the back Re-attach the Side Panel L to the printer Operation Panel System Mode Overview Menu Item SELF-DIAGNOSTIC TestDIAG. menu item list Menu operation procedure example Counter Paramete Print Contents Print FEED1 ～ FEED4PRINT1 ～ PRINT4 CUT Adjust Parameter Settings Reflect EX.I/O ModeFont LATIN9 Power Save Time CommandLBL/RBN END Maxi Code Spec Storage Area PanelUSB RS-232C LAN/WLAN Centro AES Tkip WPA Mode Wlan ModeDefault KEY Socket Port Rfid RTC Auto Diagnostics/AUTO Diagnostics Kanji None ：0000 Print conditionProgram B-EX4T1-G Sdram 32MB Eeprom 256B Head Rank SENSOR2 EXP.I/O NG Expansion I/O check contentsInternal serial I/F check contents EX.232C NG US, AU, TW SX704-RFID-U2-US-RUS, AU, KR2, TW SX704-RFID-U2-EU-R EU, SX704-RFID-U2-R Basic S None USB Memory NGBasic M None Head broken dot check/HEAD Check „ Outline of Parameter Setting Parameter SettingLCD Display Setting / Panel 1Printer setting / Printer SET Media loading / Media Load Setting for forward feed standby / Forward WaitForward feed standby position / Forward Wait POS Standby action / FW/BK ACT Pre peel-off / PRE Peel OFF Ribbon save / RBN SaveBack feed / Back Speed Standard speed/ STD 3ips Low speed / LOW 2ips ESC LF NUL / Manual Soft control setting / Software SETMenu list Soft control setting / Software SET ・ LATIN9 Character code / Font CodeControl code / Code ・ ESC, LF, NUL / ESC,LF,NUL ・ CODE1 ・ CODE2 ・ CODE3 Manual selection / ManualPeel-off wait status / Peel OFF Status Feed Key Function Euro code / Euro Code CharacterAuto head broken check / Auto HD CHK WEB Printer / WEB Printer Ribbon near end / RBN Near END External I/O mode / EX.I/OPaper / ribbon end / LBL/RBN END TYPE1：・ Disable / OFF ・ Standard / STD ・ Oracle / Oracle MaxiCode specification / Maxi CodeCompatible with the current version 2.16 XML Print method / Energy Type Power save time / PW Save TimeThreshold selection / Threshold Select Language of LCD display / LCD Language LCD LanguageMachine name / Machine Name Print page / Print Password setting / Password Contrast adjustment / ContrastMenu list of Password setting / Password Digit Hex Non Decimal System Mode „ Outline of Printer Parameter Fine Adjustment Fine adjustment value setting/ Adjust SET Max Min Step Display Sign Integer Decimal Fullfil Feed / Feed ADJCut position / CUT ADJ Digit 50.0 +3.0mm Cut position Paper feed direction Cut position Head position （ｂ）Operation example Issue count 2, Cut interval = System Mode Strip position fine adjustment 0ｍｍ +3.0mm Back feed / Back ADJ Digit 99.5 Decimal Exist Non Direction position / X AdjustDensity fine tune Thermal transfer / Tone ADJ.TRANS Digit Decimal Exist Non Step Exist Non Step Ribbon Rewinder / RBN ADJ.FWRibbon Feeder / RBN ADJ.BK Transmissive sensor fine tune / Threshold Trans Refrective sensor fine tune / Threshold Refl +10step EX4T1-G EX4T1-T Speed Issue count / Issue Count Print condition setting / Print ConditionTest Print It sets printing condition of printer for test print Print speed / Print Speed Issue type / Issue TypeSensor / Sensor Print method / Print Type Print Speed Issue CountSensor Type 3 3-dot slant line print / Slant LINE3DOT 2 1-dot slant line print / Slant LINE1DOT Character print / Characters Barcode print / Barcode Auto print Transmissive / Auto Print Trans Factory test / Factory Test Auto print Reflective / Auto Print Refl „ Outline of the Sensor Adjustment Sensor AdjustmentTemperature sensor/ Temperature Reflective sensor / Reflect Ribbon end / Ribbon Transmissive / TransPaper empty level / PE REFL./TRANS „ Outline of RAM Clear RAM ClearNo RAM clear / no RAM Clear This is a selection to prevent wrong user operation MODE1 HU CUT/RWD TYPE1 XML STD USB Status Print density Direct Thermal Parameter setting/Password settingRibbon Rewind Ribbon Back tension INFRA/OPEN Wepoff Auto SnmpNone Even XON+READY Auto ACK/BYSY TYPE1 User mode Auto paper measurement Function Enable/Disable RTC setting Wire/Wireless LAN selection / LAN/WLAN IP Address SettingUSB Network / Network Menu list of Network / Network Menu Item Wlan Power Save Wins Network setting / SettingInformation Standard Gateway / Gateway Address Basic information / Basic InformationSubnet mask / Subnet Mask Socket port / Socket Port ・ 11b/g ・ 11g Wireless LAN standard / Wlan StandardWireless LAN connection mode / Wlan Mode Wlan power save / Wlan Power Save WEP default Key / Default KEY1.3.13 802.11b channel / 802.11b Channel 1.3.14 802.11b transfer rate / 802.11b Baud Wins Address / Wins Address Wins1.3.20 LPR 2 USB Baud rate / Speed 3 RS-232CData length / Data Length Stop bit / Stop BIT 4.1 ACK/BUSY Centronics / Centro・ TYPE1 ・ TYPE2 Input prime / Input Prime „ Outline of Basic Setting Basic Setting „ Outline of the Rfid Module Setting Rfid Module Setting ID Read / ID Read Test / Test Module / Module SX704-RFID-U2 TAG IDModule type / Module Type SX704-RFID-U2-CN-R 11.2.3Tag type / TAG Country / Country RF channel / RF Channel 11.3.1Position adjustment for re-issue / ADJ Retry Position・ Auto ・ 2CH ・ 3CH ・ 4CH ・ 5CH ・ 6CH ・ 7CH ・ 8CH 11.3.3Read retry / Read Retry 11.3.2Issue retry label / Issue Retry LablesDigit 255 Decimal Non 11.4.1Output level / Power Level UHF setting / UHF Setting11.3.4Write retry / Write Retry SX704-RFID-U2-EU-R/US-R /CN-R 11.4.3AGC threshold / AGC Threshold 11.4.2Q value / Q Value 11.4.4Write AGC threshold / Write AGC Threshold 11.4.5Write retry minimum AGC / Write Retry MIN AGC Onaccess 11.5.1Tag test setting / TAG CheckPassword Write data if access pass word matches to password setting LCD Display example English 11.5.2Multi word write / Mult Write11.5.3Carrier sense / Carrier Sense Cut issue mode when the disk cutter is used For the following, refer to the parameter setting section„ LED function „ Key function Cancel „ Error messagesEnter Down No Ribbon OFF Blinking Symbols in the message„ LCD message and LED indication Head Error Dhcp Client （Ex ） ESCT20G30LFNUL （Ex ） ESCPC0010A00,0300,2,2,A,00,BLFNULＬＣＤ Display Threshold Setting Operation Example （English） Threshold SettingDepressing Pause Move to 3. Paper Sensor type Judgement Judgment display On Line Mode Online Mode LCD Display Example （English） Online Mode LCD Display Icon Online Mode Display TRANSITION, Operation example （English） Help message for paper empty *1 Help Display Help Display TRANSITION, Operation EXAMPLE（English） Online mode Error content Periodic Maintenance Procedure Remove paper debris or label glue from the media path 50 km When the Strip Module is used Troubleshooting Troubleshooting System Requirement Rfid Analyze Tool V1.5 Set upSetup Disk Installation Setup Disk consists of one CD-ROM Main Menu Application Functions File Menu EO18-33027 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF Test Option Sheet Setting Makes settings for the media to be used Select the printer model Select the test mode This menu is not available Displays Printer Version and Rfid Module Version Example Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF Rfid Analyze Tool Tag Data Rfid Analyze Tool Write/Read Results Box When U2 is selected Write/Read Results Box