When the installation plate is directly mounted on the wall

1.Securely fit the installation plate onto the wall by screws with the upper and lower catches.

2.To mount the installation plate on a concrete wall use anchor bolts. Drill the anchor bolt holes as illustrated in the above figure.

3.Place the level at the top end of the installation plate, and check that the plate is horizontal.

CAUTION

When installing the installation plate with mount- ing screws, do not use the anchor bolt holes.

Otherwise the unit may fall down and result in personal injury and property damage.

Anchor bolt

Projection 15mm or less

Fig. 10-3-4

5 mm dia. hole

6 Mounting screw Ø4 × 25L

Clip anchor (local parts)

Fig. 10-3-5

CAUTION

Failure to securely install the unit may result in personal injury and/or property damage if the unit falls.

•In case of block, brick, concrete or similar type walls, drill 5 mm dia. holes in the wall.

•Insert clip anchors for the † mounting screws.

NOTE :

•Install the installation plate using between 4 to 6 mounting screws, making sure all four corners are secure.

10-3-3. Electrical Work

1.The supply voltage must be the same as the rated voltage of the air conditioner.

2.Prepare a power source for the exclusive use of the air conditioner.

NOTE :

•Wire type :

More than H07RN-F or 60245IEC66 (1.0mm²)

CAUTION

A switch or circuit breaker that can disconnect all poles must be included in the fixed wiring.

Be sure to use an approved circuit breaker or switch.

NOTE :

•Make sure the wire length is sufficient before performing wiring work.

10-3-4. Wiring Connection

How to connect the connecting cable

Wiring the connecting cable can be carried out without removing the front panel.

1.Remove the air inlet grille. Open the air inlet grille upward and pull it toward you.

2.Remove the terminal cover and cord clamp.

3.Insert the connecting cable (or as according to local regulations/codes) into the pipe hole on the wall.

4.Pull the connecting cable through the cable slot on the rear panel so that it protrudes about 15 cm out of the front.

5.Insert the connecting cable fully into the terminal block and secure it tightly with screws.

Make a loop with the earth wire under the terminal block and secure it with the earth screw.

6.Tightening torque: 1.2 N•m (0.12 kgf•m)

7.Secure the connecting cable with the cord clamp.

8.Attach the terminal cover, rear plate bushing and air inlet grille on the indoor unit.

CAUTION

•Be sure to refer to the wiring system diagram labeled inside the front panel.

•Check local electrical regulations for any specific wiring instructions or limitations.

– 59 –

Page 58 Page 60
Page 59
Image 59
Toshiba RAS-10SAVP-E, RAS-B13SKVP-E When the installation plate is directly mounted on the wall, Electrical Work
Page 58 Page 60

RAS-10SAVP-E, RAS-B10SKVP-E, RAS-B13SKVP-E specifications

Toshiba has established itself as a leader in the HVAC market, known for its innovative technologies and reliable performance. Among its range of air conditioning units, the Toshiba RAS-B10SKVP-E, RAS-10SAVP-E, and RAS-B13SKVP-E models stand out for their efficiency and advanced features.

The Toshiba RAS-B10SKVP-E is designed for optimal cooling and heating efficiency, making it an ideal choice for small to medium-sized rooms. One of its main features is the Super Hi-M-PAM inverter technology, which enhances energy savings by continuously adjusting the compressor speed to match the cooling demand. This results in lower energy consumption while maintaining a stable temperature. Additionally, the unit boasts a 4-in-1 operation mode that allows users to select cooling, heating, dehumidification, or ventilating modes, ensuring maximum comfort at all times.

Similarly, the RAS-10SAVP-E model incorporates advanced features such as an eco-friendly refrigerant, R32, which has a lower Global Warming Potential (GWP) compared to traditional refrigerants. This model is equipped with a high-efficiency filter that captures dust and allergens, ensuring cleaner air quality. The sleek design allows for easy integration into various interior styles, while its quiet operation makes it a preferred choice for residential environments.

The RAS-B13SKVP-E model takes performance to the next level with a robust cooling capacity, designed for larger spaces. This model utilizes Toshiba's unique DC Hybrid Inverter technology, which not only enhances cooling efficiency but also facilitates faster temperature control. A notable characteristic of this unit is its wide-angle air distribution system, which allows for even airflow throughout the room, enhancing comfort.

In addition to these features, all three models are equipped with smart controls that enable users to operate their air conditioning systems remotely via mobile devices. This connectivity adds convenience and ensures that users can manage their indoor climate at their fingertips. They also come with user-friendly interfaces and programmable timers, allowing for personalized comfort settings.

In conclusion, the Toshiba RAS-B10SKVP-E, RAS-10SAVP-E, and RAS-B13SKVP-E air conditioning units combine energy efficiency, innovative technology, and user-friendly features to deliver exceptional indoor comfort. With their advanced technologies, these models are ideal choices for anyone seeking reliable and effective climate control solutions.
Top Page Image Contents