Toshiba RAV-SP564ATZG-E, RAV-SP804ATZG-E, RAV-SP804ATZ-E 130, Error display, Error contents

2)Error display

The error which is generating at present and the latest error (Latest error information including present) can be confirmed by lighting LED D800 toD804 on the outdoor control P.C. board.

a)When all DIP switch SW803 are OFF, the status of error which is generating at present is displayed.

b)<1> only of DIP switch SW803 is turned on, the error which generated before (Latest error information including present) is displayed.a)

c)If there is an error, any of LED D800 to D804 goes on. (Display 1)

d)When pushing the pushdown button switch SW800 for approx. 1 second, the display is exchanged. (Display 2)

e)When pushing SW800 again or after 2 minutes, the status returns to that of Display •.

Present error			Latest error
	SW803			SW803
					4
		4
					3
		3
					2
		2
	ON			ON	1
		1

(Legend)

lD800 (Yellow)

lD801 (Yellow)

¥	D802	(Yellow)	l : Go off, ¡ : Go on, ¥ : Flash
l	D803	(Yellow)
l D804		(Yellow)
¡ D805		(Green)

Display 1)	Display 2)	Error contents	Wired remote controller
(Initial display)	(SW800 operation)		Error code

lllll¡	lllll¡	Normal	—
	ll¥ll¡	Discharge temp. sensor (TD) error	F04
	l¥¥ll¡	Heat exchanger temp. sensor (TE) error	F06
	¥¥¥ll¡	Heat exchanger temp. sensor (TL) error	F06, F07
¡¡ll¡¡	lll¥l¡	Outside temp. sensor (TO) error	F08
	ll¥¥l¡	Suction temp. sensor (TS) error	F06, F12
	¥l¥¥l¡	Heat sink temp. sensor (TH) error	F13,	L29
	¥¥¥¥l¡	Heat exchanger sensor (TE, TS) miswiring	F06, F15
	¥¥¥¥¥¡	EEPROM error	F31,	L29
	¥llll¡	Compressor break down	H01
ll¡l¡¡	l¥lll¡	Compressor lock	H02
	¥¥lll¡	Current detection circuit error	H03
	ll¥ll¡	Case thermostat operation	H04,	P04
	l¥l¥l¡	Model unset	L10, L29
l¡¡l¡¡ ¥l¥¥¥¡		Communication error between MCU	L29
	¥¥¥¥¥¡	Other error (Compressor disorder, etc.)	Error is not determined.
	¥¥lll¡	Discharge temp. error	P03
	¥l¥ll¡	Power supply error	P04,	P05
	¥¥¥ll¡	Heat sink overheat error	P07, L29
	¥¥¥¥l¡	Gas leak detection	P15, L29
¡¡¡l¡¡ ¥¥ll¥¡		4-way valve reverse error	P19, L29
	ll¥l¥¡	High pressure protective operation	P04, P20
	l¥¥l¥¡	Fan system error	P22
	l¥l¥¥¡	Driving element short-circuit	P26
	¥l¥¥¥¡	Position detection circuit erro	P29

∗As the error code displayed on the wired remote controller may differ according to type of indoor model, multiple codes are described.

– 130 –