Appendix B. Specifications, Switching | Western Telematic AFS-16-1

Appendix B. Specifications

Switch Card: Up to 16 Modules

Interface: RJ45-3, Three Jacks, 8 Pins Switched Common Jack to A or B Jack.

Contacts: High Reliability, Mechanical Relays, Break-Before-Make Contacts with 1 Amp @ 30 VDC Rating, 100 Million Cycle Life.

Switching:

Manual: Individual Toggle Switch, Gang Switching from Control Module.

Code/Web Browser: By Slot Number or by Name.

Card Rack and Control Unit

Ethernet Port: 10/100Base-T

Serial Console Port: 1 each, RJ45, RS232C

AUX Port: 5-Pin Quick-Connect Terminal Block for External Connection for Alarm Output, Monitor Input and Ground. Monitor Input Signal is always read relative to ground signal.

Low Monitor Input Signal: 0V to -48V

High Monitor Input Signal: +5V to +48V

RS232 Port Interface:

Connectors: One (1) RJ45 connector (DTE pinout.)

Coding: 7/8 bits, Even, Odd, No Parity, 1, 2 Stop Bits.

Flow Control: XON/XOFF, RTS/CTS, Both, or None.

Data Rate: 300 to 115.2K bps (all standard rates).

Inactivity Timeout: No activity timeout disconnects port/modem sessions. Off, 5, 15, 30, 90 minutes.

Break: Send Break or Inhibit Break

Site ID: 32 Characters.

Port Name: 16 Characters per port.

Usernames & Passwords: 32 character usernames; 16 character passwords (case sensitive.) Up to 128 pairs, definable circuit module, circuit group and

system access.

Physical/Environmental:

Size: 5.25” x 19.00” x 6.75” (H x W x D)

Power: 100/240 VAC 50/60 Hz, 15 watts

Weight: Shipping Weight, Fully Loaded, 15 pounds

Operating Temperature: 32˚F to 122˚F (0˚C to 50˚C)

Humidity: 10 - 90% RH

Venting: Side vents are used to dissipate heat generated within the unit. When mounting the unit in an equipment rack, make certain to allow adequate clearance for venting.

Apx-2

Image 125

Western Telematic AFS-16-1 manual Appendix B. Specifications, Switching, Physical/Environmental, Apx-2

Contents

AFS-16-1 Secure Racking Shock Hazard Do Not Enter Lithium Battery Two Power Supply Cables Disconnect Power Table of Contents Basic Configuration Telnet & SSH Functions Upgrading AFS-16 Firmware Command Reference Guide Vii List of Figures Introduction Security and Co-Location Features Environmental Monitoring and Management Typographic ConventionsWTI Management Utility Bold Font Unit Description Dual Power Supply Module Power Switch and on Indicator Control Module Control Module Unit Description Circuit Module Circuit Module Connect Your PC to the AFS-16 Apply Power to the AFS-16Getting Started Communicating with the AFS-16 Fallback Switching Text Interface Fallback Switching Fallback Switching Web Browser Interface Connecting the Network Cable Hardware InstallationConnecting the Power Supply Cables Connecting an External Modem Optional Connecting a Local Control Device A/C/B Connectors Module Set UpCircuit Module Set Up Control Module SetUp Text Interface Basic ConfigurationCommunicating with the AFS-16 Unit Web Browser Interface Access Via PDA Configuration Menus Defining System Parameters Basic Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Log Configuration Web Browser Interface Callback Security Basic Configuration Scripting Options Basic Configuration User Accounts Command Access Levels Granting Circuit Module Access Adding User Accounts Managing User AccountsViewing User Accounts Basic Configuration Deleting User Accounts Modifying User Accounts Circuit Configuration Viewing Circuit Groups Circuit Group Directory Deleting Circuit Groups Adding Circuit GroupsModifying Circuit Groups Serial Port Configuration Menu Serial Port ConfigurationCommunication Settings 1. RS232 Port Modes Port Mode Parameters Network Configuration Network Port Parameters Network Parameters Basic Configuration IP Security Basic Configuration Net/Mask Pairs Except Domain Name Server Static Route Snmp Access Parameters Snmp Trap Parameters Ldap Parameters Group Membership Value Type Default = DN Basic Configuration Tacacs Parameters Basic Configuration Radius Parameters WTI-Group-Access=111000 WTI-Circuit-Access=0101WTI-Super=2 Example Email Messaging Parameters Save User Selected Parameters Restore Configuration Adding Ping-No-Answer Profiles Ping-No-Answer Fallback Switching Ping-No-Answer Fallback Switching Deleting Ping-No-Answer Profiles Viewing Ping-No-Answer ProfilesModifying Ping-No-Answer Profiles Alarm Configuration Output Contacts Control Module AUX Connector Output Contacts Over Temperature Alarms Alarm Configuration Defining Ping-No-Answer IP Addresses Ping-No-Answer AlarmConfiguring the Ping-No-Answer Alarm Alarm Configuration Invalid Access Lockout Alarm Alarm Configuration Power Cycle Alarm Monitor/Alarm Input Alarm Configuration High Low Monitor Input Level Settings Alarm Configuration Network Status Screen Status ScreensProduct Status Circuit Status Screen Circuit Group Status Screen Audit Log Event Logs Temperature Log Alarm Log Circuit Control Screen Web Browser Interface A/B Switching Web Browser InterfaceOperation Circuit Group Control Screen Web Browser Interface Operation Circuit Status Screen Text Interface A/B Switching Text Interface TB 2 Enter or /TB Servers Enter 2. A/B Switching Commands Text InterfaceTA 1 Enter or /TA Datacenter Enter TA ROUTER,Y or /T 2,B,Y B Enter or /T SERVERS,A EnterTB 1+3+4 Enter +3+4,B Enter TA 13 Enter Manual Operation Logging Out of Command Mode SSH Encryption Telnet & SSH FunctionsEnter 10-1 Telnet ip port raw Enter Creating an Outbound Telnet ConnectionTelnet 255.255.255.255 2000 raw Enter 10-2 SSH ip -l username Enter Creating an Outbound SSH ConnectionUsername SSH 255.255.255.255 -l employee Enter 11-1 ConfigurationSyslog Messages 11-2 Testing Syslog Configuration 12-1 Snmp Traps 12-2 Testing the Snmp Trap Function Configuration via Snmp AFS-16 Snmp Agent SNMPv3 Authentication and EncryptionUserTableuserAccessLevel Account access level Operation via Snmp Adding Users Viewing UsersModifying Users Deleting Users Controlling Circuits Circuit Control via SnmpControlling Circuit Groups 13-3 Circuit Status Viewing AFS-16 Status via Snmp155 Unit Environment Status 13-5 Sending Traps via Snmp 14-1 Setting Up SSL Encryption 14-2 Creating a Self Signed Certificate 14-3 Creating a Signed Certificate 14-4 Downloading the Server Private Key 15-1 Saving and Restoring Configuration ParametersSending Parameters to a File 15-2 Restoring Saved Parameters 15-3 Restoring Previously Saved Parameters 16-1 Upgrading AFS-16 Firmware 16-2 Command Conventions Command Reference GuideTA * Enter 17-1 17-2 Command Summary Display Circuit Status Screen Command SetDisplay Circuit Group Status Screen Display Network Status Log Functions Exit Command ModeDisplay Site ID / Unit Information Connect TA 2+3,Y Enter Toggle to a PositionToggle to B Position TB 2+3,Y Enter Set All Circuits to Default States Toggle Command+3,A,Y Enter Send Parameters to File Send SSH Key Unlock Port Invalid Access LockoutTelnet Outbound Telnet Format /TELNET ip port raw Enter Format /SSH ip -l username Enter SSH Outbound SSHSet System Parameters Set Serial Port Parameters Alarm Configuration Parameters PNA Configure Ping-No-Answer FunctionCircuit Group Parameters Network Port Parameters Test Test Network Parameters Reboot System DefaultUpgrade Firmware When not connected When connectedAppendix A. Interface Description Serial Port RS232 Switching Appendix B. SpecificationsPhysical/Environmental Apx-2 Apx-3 Appendix C. Customer Service Apx-4 Trademark and Copyright InformationTrademarks and Copyrights Used in this Manual Index-1 Index Radius CLI Index-2 Ldap Index-3 Tacacs Index-4 NTP Index-5 Index-6 Snmp Index-7 SNMPV3 Index-8