Testing the Snmp Trap Function, 12-2 | Western Telematic AFS-16-1

SNMP Traps

12.2. Testing the SNMP Trap Function

After you have finished setting up the SNMP Trap function, it is recommended to test the configuration to ensure that it is working correctly. To test configuration of the SNMP Trap function, proceed as follows:

1.Configure the SNMP Trap function as described in Section 12.1.

2.Access the Text Interface command mode using an account that permits Administrator or SuperUser level commands, then invoke the "/TEST" command at the AFS-16 command prompt. Note that the /TEST Command is only available in Administrator and SuperUser Mode.

3.Select Item 1 or 2 to send an SNMP test trap to Manager 1 or 2, respectively. It is possible that the ARP table will not be properly setup. If this occurs a message to that effect is displayed and the AFS-16 immediately refreshes the ARP table. Repeat steps 2 and 3 to try again.

For more information on the /TEST command and the Test Menu, please refer to Section 11.2.

12-2

Image 99

Western Telematic AFS-16-1 manual Testing the Snmp Trap Function, 12-2

Contents

AFS-16-1 Secure Racking Shock Hazard Do Not Enter Lithium Battery Two Power Supply Cables Disconnect Power Table of Contents Basic Configuration Telnet & SSH Functions Upgrading AFS-16 Firmware Command Reference Guide Vii List of Figures Introduction Security and Co-Location Features Bold Font Typographic ConventionsEnvironmental Monitoring and Management WTI Management Utility Dual Power Supply Module  Power Switch and on IndicatorUnit Description Control Module Control Module Unit Description Circuit Module Circuit Module Apply Power to the AFS-16 Getting StartedConnect Your PC to the AFS-16 Communicating with the AFS-16 Fallback Switching Text Interface Fallback Switching Fallback Switching Web Browser Interface Hardware Installation Connecting the Power Supply CablesConnecting the Network Cable Connecting an External Modem Optional Connecting a Local Control Device Control Module SetUp Module Set UpA/C/B Connectors Circuit Module Set Up Basic Configuration Communicating with the AFS-16 UnitText Interface Web Browser Interface Access Via PDA Configuration Menus Defining System Parameters Basic Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Log Configuration Web Browser Interface Callback Security Basic Configuration Scripting Options Basic Configuration User Accounts Command Access Levels Granting Circuit Module Access Managing User Accounts Viewing User AccountsAdding User Accounts Basic Configuration Deleting User Accounts Modifying User Accounts Circuit Configuration Viewing Circuit Groups Circuit Group Directory Adding Circuit Groups Modifying Circuit GroupsDeleting Circuit Groups 1. RS232 Port Modes Serial Port ConfigurationSerial Port Configuration Menu Communication Settings Port Mode Parameters Network Configuration Network Port Parameters Network Parameters Basic Configuration IP Security Basic Configuration Net/Mask Pairs Except Domain Name Server Static Route Snmp Access Parameters Snmp Trap Parameters Ldap Parameters Group Membership Value Type Default = DN Basic Configuration Tacacs Parameters Basic Configuration Radius Parameters Example WTI-Circuit-Access=0101WTI-Group-Access=111000 WTI-Super=2 Email Messaging Parameters Save User Selected Parameters Restore Configuration Adding Ping-No-Answer Profiles Ping-No-Answer Fallback Switching Ping-No-Answer Fallback Switching Viewing Ping-No-Answer Profiles Modifying Ping-No-Answer ProfilesDeleting Ping-No-Answer Profiles Alarm Configuration Output Contacts Control Module AUX Connector Output Contacts Over Temperature Alarms Alarm Configuration Ping-No-Answer Alarm Configuring the Ping-No-Answer AlarmDefining Ping-No-Answer IP Addresses Alarm Configuration Invalid Access Lockout Alarm Alarm Configuration Power Cycle Alarm Monitor/Alarm Input Alarm Configuration High Low Monitor Input Level Settings Alarm Configuration Status Screens Product StatusNetwork Status Screen Circuit Status Screen Circuit Group Status Screen Audit Log Event Logs Temperature Log Alarm Log A/B Switching Web Browser Interface OperationCircuit Control Screen Web Browser Interface Circuit Group Control Screen Web Browser Interface Operation Circuit Status Screen Text Interface A/B Switching Text Interface 2. A/B Switching Commands Text Interface TA 1 Enter or /TA Datacenter EnterTB 2 Enter or /TB Servers Enter TA 13 Enter B Enter or /T SERVERS,A EnterTA ROUTER,Y or /T 2,B,Y TB 1+3+4 Enter +3+4,B Enter Manual Operation Logging Out of Command Mode 10-1 Telnet & SSH FunctionsSSH Encryption Enter 10-2 Creating an Outbound Telnet ConnectionTelnet ip port raw Enter Telnet 255.255.255.255 2000 raw Enter SSH 255.255.255.255 -l employee Enter Creating an Outbound SSH ConnectionSSH ip -l username Enter Username Configuration Syslog Messages11-1 11-2 Testing Syslog Configuration 12-1 Snmp Traps 12-2 Testing the Snmp Trap Function Operation via Snmp AFS-16 Snmp Agent SNMPv3 Authentication and EncryptionConfiguration via Snmp UserTableuserAccessLevel Account access level Deleting Users Viewing UsersAdding Users Modifying Users 13-3 Circuit Control via SnmpControlling Circuits Controlling Circuit Groups Unit Environment Status Viewing AFS-16 Status via SnmpCircuit Status 155 13-5 Sending Traps via Snmp 14-1 Setting Up SSL Encryption 14-2 Creating a Self Signed Certificate 14-3 Creating a Signed Certificate 14-4 Downloading the Server Private Key Saving and Restoring Configuration Parameters Sending Parameters to a File15-1 15-2 Restoring Saved Parameters 15-3 Restoring Previously Saved Parameters 16-1 Upgrading AFS-16 Firmware 16-2 17-1 Command Reference GuideCommand Conventions TA * Enter 17-2 Command Summary Display Network Status Command SetDisplay Circuit Status Screen Display Circuit Group Status Screen Connect Exit Command ModeLog Functions Display Site ID / Unit Information TB 2+3,Y Enter Toggle to a PositionTA 2+3,Y Enter Toggle to B Position Send Parameters to File Toggle CommandSet All Circuits to Default States +3,A,Y Enter Format /TELNET ip port raw Enter Unlock Port Invalid Access LockoutSend SSH Key Telnet Outbound Telnet Set Serial Port Parameters SSH Outbound SSHFormat /SSH ip -l username Enter Set System Parameters Network Port Parameters PNA Configure Ping-No-Answer FunctionAlarm Configuration Parameters Circuit Group Parameters Reboot System Default Upgrade FirmwareTest Test Network Parameters Serial Port RS232 When connectedWhen not connected Appendix A. Interface Description Apx-2 Appendix B. SpecificationsSwitching Physical/Environmental Apx-3 Appendix C. Customer Service Trademark and Copyright Information Trademarks and Copyrights Used in this ManualApx-4 Index-1 Index Radius CLI Index-2 Ldap Index-3 Tacacs Index-4 NTP Index-5 Index-6 Snmp Index-7 SNMPV3 Index-8