Power Cycle Alarm | Western Telematic AFS-16-1 instruction

Alarm Configuration

7.5. The Power Cycle Alarm

The Power Cycle Alarm can provide notification when input power to the AFS-16 unit is lost and then restored. When the power supply is lost and then restored, the AFS-16 can provide notification via Email, Syslog Message or SNMP Trap.

To configure the Power Cycle Alarm, you must access the AFS-16 command mode using a password that permits Administrator Level commands. The Power Cycle Alarm configuration menu offers the following parameters:

•Trigger Enable: Enables/Disables the trigger for this alarm. When Disabled, this alarm will be suppressed. (Default = On.)

•Email Message: Enables/Disables email notification for this alarm. (Default = On.)

Note: If either of the "Copy to All Triggers" options is selected, then email notification for other alarms will be switched On or Off as indicated by this parameter.

Address 1, 2, and 3: These parameters are used to select which of the three email addresses defined via the "Email Messages" menu (see Section 5.9.11) will receive the email alarm notification messages generated by this alarm.

The Address parameters can be used to select one, or any combination of the addresses defined via the Email Messages menu. (Default = All On.)

Note: If Email addresses have been previously specified, then the text under the parameters will list the current, user defined email addresses.

•Subject: This parameter is used to define the text that will appear in the "Subject" field for all email notification messages generated by this alarm. (Default = "Alarm: Power Cycle")

7-9

Image 76

Western Telematic AFS-16-1 manual Power Cycle Alarm

Contents

AFS-16-1 Shock Hazard Do Not Enter Lithium Battery Secure Racking Two Power Supply Cables Disconnect Power Table of Contents Basic Configuration Telnet & SSH Functions Upgrading AFS-16 Firmware Command Reference Guide List of Figures Vii Security and Co-Location Features Introduction Typographic Conventions Environmental Monitoring and ManagementWTI Management Utility Bold Font  Power Switch and on Indicator Dual Power Supply ModuleUnit Description Control Module Control Module Unit Description Circuit Module Circuit Module Getting Started Apply Power to the AFS-16Connect Your PC to the AFS-16 Communicating with the AFS-16 Fallback Switching Fallback Switching Text Interface Fallback Switching Web Browser Interface Connecting the Power Supply Cables Hardware InstallationConnecting the Network Cable Connecting a Local Control Device Connecting an External Modem Optional Module Set Up A/C/B ConnectorsCircuit Module Set Up Control Module SetUp Communicating with the AFS-16 Unit Basic ConfigurationText Interface Web Browser Interface Access Via PDA Configuration Menus Defining System Parameters Basic Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Log Configuration Web Browser Interface Callback Security Basic Configuration Scripting Options Basic Configuration Command Access Levels User Accounts Granting Circuit Module Access Viewing User Accounts Managing User AccountsAdding User Accounts Basic Configuration Modifying User Accounts Deleting User Accounts Circuit Configuration Circuit Group Directory Viewing Circuit Groups Modifying Circuit Groups Adding Circuit GroupsDeleting Circuit Groups Serial Port Configuration Serial Port Configuration MenuCommunication Settings 1. RS232 Port Modes Port Mode Parameters Network Configuration Network Port Parameters Network Parameters Basic Configuration IP Security Basic Configuration Except Net/Mask Pairs Static Route Domain Name Server Snmp Access Parameters Snmp Trap Parameters Ldap Parameters Group Membership Value Type Default = DN Basic Configuration Tacacs Parameters Basic Configuration Radius Parameters WTI-Circuit-Access=0101 WTI-Group-Access=111000WTI-Super=2 Example Email Messaging Parameters Restore Configuration Save User Selected Parameters Ping-No-Answer Fallback Switching Adding Ping-No-Answer Profiles Ping-No-Answer Fallback Switching Modifying Ping-No-Answer Profiles Viewing Ping-No-Answer ProfilesDeleting Ping-No-Answer Profiles Alarm Configuration Control Module AUX Connector Output Contacts Output Contacts Over Temperature Alarms Alarm Configuration Configuring the Ping-No-Answer Alarm Ping-No-Answer AlarmDefining Ping-No-Answer IP Addresses Alarm Configuration Invalid Access Lockout Alarm Alarm Configuration Power Cycle Alarm Monitor/Alarm Input Alarm Configuration Monitor Input Level Settings High Low Alarm Configuration Product Status Status ScreensNetwork Status Screen Circuit Status Screen Circuit Group Status Screen Event Logs Audit Log Alarm Log Temperature Log Operation A/B Switching Web Browser InterfaceCircuit Control Screen Web Browser Interface Circuit Group Control Screen Web Browser Interface Operation A/B Switching Text Interface Circuit Status Screen Text Interface TA 1 Enter or /TA Datacenter Enter 2. A/B Switching Commands Text InterfaceTB 2 Enter or /TB Servers Enter B Enter or /T SERVERS,A Enter TA ROUTER,Y or /T 2,B,YTB 1+3+4 Enter +3+4,B Enter TA 13 Enter Logging Out of Command Mode Manual Operation Telnet & SSH Functions SSH EncryptionEnter 10-1 Creating an Outbound Telnet Connection Telnet ip port raw EnterTelnet 255.255.255.255 2000 raw Enter 10-2 Creating an Outbound SSH Connection SSH ip -l username EnterUsername SSH 255.255.255.255 -l employee Enter Syslog Messages Configuration11-1 Testing Syslog Configuration 11-2 Snmp Traps 12-1 Testing the Snmp Trap Function 12-2 AFS-16 Snmp Agent SNMPv3 Authentication and Encryption Configuration via SnmpUserTableuserAccessLevel Account access level Operation via Snmp Viewing Users Adding UsersModifying Users Deleting Users Circuit Control via Snmp Controlling CircuitsControlling Circuit Groups 13-3 Viewing AFS-16 Status via Snmp Circuit Status155 Unit Environment Status Sending Traps via Snmp 13-5 Setting Up SSL Encryption 14-1 Creating a Self Signed Certificate 14-2 Creating a Signed Certificate 14-3 Downloading the Server Private Key 14-4 Sending Parameters to a File Saving and Restoring Configuration Parameters15-1 Restoring Saved Parameters 15-2 Restoring Previously Saved Parameters 15-3 Upgrading AFS-16 Firmware 16-1 16-2 Command Reference Guide Command ConventionsTA * Enter 17-1 Command Summary 17-2 Command Set Display Circuit Status ScreenDisplay Circuit Group Status Screen Display Network Status Exit Command Mode Log FunctionsDisplay Site ID / Unit Information Connect Toggle to a Position TA 2+3,Y EnterToggle to B Position TB 2+3,Y Enter Toggle Command Set All Circuits to Default States+3,A,Y Enter Send Parameters to File Unlock Port Invalid Access Lockout Send SSH KeyTelnet Outbound Telnet Format /TELNET ip port raw Enter SSH Outbound SSH Format /SSH ip -l username EnterSet System Parameters Set Serial Port Parameters PNA Configure Ping-No-Answer Function Alarm Configuration ParametersCircuit Group Parameters Network Port Parameters Upgrade Firmware Reboot System DefaultTest Test Network Parameters When connected When not connectedAppendix A. Interface Description Serial Port RS232 Appendix B. Specifications SwitchingPhysical/Environmental Apx-2 Appendix C. Customer Service Apx-3 Trademarks and Copyrights Used in this Manual Trademark and Copyright InformationApx-4 Index Index-1 Index-2 Radius CLI Index-3 Ldap Index-4 Tacacs Index-5 NTP Index-6 Index-7 Snmp Index-8 SNMPV3