Alarm Configuration | Western Telematic AFS-16-1 instruction

Alarm Configuration

•Email Message: Enables/Disables email notification for this alarm. (Default = On.)

Note: If either of the "Copy to All Triggers" options is selected, then email notification for other alarms will be switched On or Off as indicated by this parameter.

Address 1, 2, and 3: These parameters are used to determine which of the three email addresses defined via the "Email Messages" menu will receive the email alarm notification messages generated by this alarm. The Address parameters can be used to select one, or any combination of the addresses defined via the Email Messages menu. (Default = All On.)

Note: If Email addresses have been previously defined, then the text under the parameters will list the current, user defined email addresses.

•Subject: This parameter is used to define the text that will appear in the "Subject" field for all email notification messages generated by this alarm. (Default = "Alarm: Over Temperature (Initial)" or "Alarm: Over Temperature (Critical)".)

•Contact Output Enable: Activates/deactivates the Output Contacts on the AFS-16 Control Module AUX Connector. When the Contact Output Enable parameter is set to "On", the Common line will be switched from the Normally Closed contact to the Normally Open contact when an Over-Temperature Alarm is generated. For more information on the Output Contacts, please refer to Section 7.1. (Default = On.)

Note: If either of the "Copy to All Triggers" options is selected, then the Contact Output Enable parameter for other alarms will also be enabled or disabled as specified by this parameter.

7-4

Image 71

Western Telematic AFS-16-1 manual Alarm Configuration

Contents

AFS-16-1 Secure Racking Shock Hazard Do Not Enter Lithium Battery Two Power Supply Cables Disconnect Power Table of Contents Basic Configuration Telnet & SSH Functions Upgrading AFS-16 Firmware Command Reference Guide Vii List of Figures Introduction Security and Co-Location Features Bold Font Typographic ConventionsEnvironmental Monitoring and Management WTI Management Utility Unit Description Dual Power Supply Module Power Switch and on Indicator Control Module Control Module Unit Description Circuit Module Circuit Module Connect Your PC to the AFS-16 Apply Power to the AFS-16Getting Started Communicating with the AFS-16 Fallback Switching Text Interface Fallback Switching Fallback Switching Web Browser Interface Connecting the Network Cable Hardware InstallationConnecting the Power Supply Cables Connecting an External Modem Optional Connecting a Local Control Device Control Module SetUp Module Set UpA/C/B Connectors Circuit Module Set Up Text Interface Basic ConfigurationCommunicating with the AFS-16 Unit Web Browser Interface Access Via PDA Configuration Menus Defining System Parameters Basic Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Log Configuration Web Browser Interface Callback Security Basic Configuration Scripting Options Basic Configuration User Accounts Command Access Levels Granting Circuit Module Access Adding User Accounts Managing User AccountsViewing User Accounts Basic Configuration Deleting User Accounts Modifying User Accounts Circuit Configuration Viewing Circuit Groups Circuit Group Directory Deleting Circuit Groups Adding Circuit GroupsModifying Circuit Groups 1. RS232 Port Modes Serial Port ConfigurationSerial Port Configuration Menu Communication Settings Port Mode Parameters Network Configuration Network Port Parameters Network Parameters Basic Configuration IP Security Basic Configuration Net/Mask Pairs Except Domain Name Server Static Route Snmp Access Parameters Snmp Trap Parameters Ldap Parameters Group Membership Value Type Default = DN Basic Configuration Tacacs Parameters Basic Configuration Radius Parameters Example WTI-Circuit-Access=0101WTI-Group-Access=111000 WTI-Super=2 Email Messaging Parameters Save User Selected Parameters Restore Configuration Adding Ping-No-Answer Profiles Ping-No-Answer Fallback Switching Ping-No-Answer Fallback Switching Deleting Ping-No-Answer Profiles Viewing Ping-No-Answer ProfilesModifying Ping-No-Answer Profiles Alarm Configuration Output Contacts Control Module AUX Connector Output Contacts Over Temperature Alarms Alarm Configuration Defining Ping-No-Answer IP Addresses Ping-No-Answer AlarmConfiguring the Ping-No-Answer Alarm Alarm Configuration Invalid Access Lockout Alarm Alarm Configuration Power Cycle Alarm Monitor/Alarm Input Alarm Configuration High Low Monitor Input Level Settings Alarm Configuration Network Status Screen Status ScreensProduct Status Circuit Status Screen Circuit Group Status Screen Audit Log Event Logs Temperature Log Alarm Log Circuit Control Screen Web Browser Interface A/B Switching Web Browser InterfaceOperation Circuit Group Control Screen Web Browser Interface Operation Circuit Status Screen Text Interface A/B Switching Text Interface TB 2 Enter or /TB Servers Enter 2. A/B Switching Commands Text InterfaceTA 1 Enter or /TA Datacenter Enter TA 13 Enter B Enter or /T SERVERS,A EnterTA ROUTER,Y or /T 2,B,Y TB 1+3+4 Enter +3+4,B Enter Manual Operation Logging Out of Command Mode 10-1 Telnet & SSH FunctionsSSH Encryption Enter 10-2 Creating an Outbound Telnet ConnectionTelnet ip port raw Enter Telnet 255.255.255.255 2000 raw Enter SSH 255.255.255.255 -l employee Enter Creating an Outbound SSH ConnectionSSH ip -l username Enter Username 11-1 ConfigurationSyslog Messages 11-2 Testing Syslog Configuration 12-1 Snmp Traps 12-2 Testing the Snmp Trap Function Operation via Snmp AFS-16 Snmp Agent SNMPv3 Authentication and EncryptionConfiguration via Snmp UserTableuserAccessLevel Account access level Deleting Users Viewing UsersAdding Users Modifying Users 13-3 Circuit Control via SnmpControlling Circuits Controlling Circuit Groups Unit Environment Status Viewing AFS-16 Status via SnmpCircuit Status 155 13-5 Sending Traps via Snmp 14-1 Setting Up SSL Encryption 14-2 Creating a Self Signed Certificate 14-3 Creating a Signed Certificate 14-4 Downloading the Server Private Key 15-1 Saving and Restoring Configuration ParametersSending Parameters to a File 15-2 Restoring Saved Parameters 15-3 Restoring Previously Saved Parameters 16-1 Upgrading AFS-16 Firmware 16-2 17-1 Command Reference GuideCommand Conventions TA * Enter 17-2 Command Summary Display Network Status Command SetDisplay Circuit Status Screen Display Circuit Group Status Screen Connect Exit Command ModeLog Functions Display Site ID / Unit Information TB 2+3,Y Enter Toggle to a PositionTA 2+3,Y Enter Toggle to B Position Send Parameters to File Toggle CommandSet All Circuits to Default States +3,A,Y Enter Format /TELNET ip port raw Enter Unlock Port Invalid Access LockoutSend SSH Key Telnet Outbound Telnet Set Serial Port Parameters SSH Outbound SSHFormat /SSH ip -l username Enter Set System Parameters Network Port Parameters PNA Configure Ping-No-Answer FunctionAlarm Configuration Parameters Circuit Group Parameters Test Test Network Parameters Reboot System DefaultUpgrade Firmware Serial Port RS232 When connectedWhen not connected Appendix A. Interface Description Apx-2 Appendix B. SpecificationsSwitching Physical/Environmental Apx-3 Appendix C. Customer Service Apx-4 Trademark and Copyright InformationTrademarks and Copyrights Used in this Manual Index-1 Index Radius CLI Index-2 Ldap Index-3 Tacacs Index-4 NTP Index-5 Index-6 Snmp Index-7 SNMPV3 Index-8