Secure Racking | Western Telematic AFS-16-1 specification

Warnings and Cautions:

Installation Instructions

Secure Racking

If Secure Racked units are installed in a closed or multi-unit rack assembly, they may require further evaluation by Certification Agencies. The following items must be considered.

1.The ambient within the rack may be greater than room ambient. Installation should be such that the amount of air flow required for safe operation is not compromised. The maximum temperature for the equipment in this environment is 45°C. Consideration should be given to the maximum rated ambient.

2.Installation should be such that a hazardous stability condition is not achieved due to uneven loading.

Input Supply

Check nameplate ratings to assure there is no overloading of supply circuits that could have an effect on overcurrent protection and supply wiring.

Grounding

Reliable earthing of this equipment must be maintained. Particular attention should be given to supply connections when connecting to power strips, rather than direct connections to the branch circuit.

No Serviceable Parts Inside; Authorized Service Personnel Only

Do not attempt to repair or service this device yourself. Internal components must be serviced by authorized personnel only.

•Shock Hazard - Do Not Enter

•Lithium Battery

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.

i

Image 2

Western Telematic AFS-16-1 manual Secure Racking, Shock Hazard Do Not Enter Lithium Battery

Contents

AFS-16-1 Shock Hazard Do Not Enter Lithium Battery Secure Racking Two Power Supply Cables Disconnect Power Table of Contents Basic Configuration Telnet & SSH Functions Upgrading AFS-16 Firmware Command Reference Guide List of Figures Vii Security and Co-Location Features Introduction WTI Management Utility Typographic ConventionsEnvironmental Monitoring and Management Bold Font Unit Description Dual Power Supply Module Power Switch and on Indicator Control Module Control Module Unit Description Circuit Module Circuit Module Connect Your PC to the AFS-16 Apply Power to the AFS-16Getting Started Communicating with the AFS-16 Fallback Switching Fallback Switching Text Interface Fallback Switching Web Browser Interface Connecting the Network Cable Hardware InstallationConnecting the Power Supply Cables Connecting a Local Control Device Connecting an External Modem Optional Circuit Module Set Up Module Set UpA/C/B Connectors Control Module SetUp Text Interface Basic ConfigurationCommunicating with the AFS-16 Unit Web Browser Interface Access Via PDA Configuration Menus Defining System Parameters Basic Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Log Configuration Web Browser Interface Callback Security Basic Configuration Scripting Options Basic Configuration Command Access Levels User Accounts Granting Circuit Module Access Adding User Accounts Managing User AccountsViewing User Accounts Basic Configuration Modifying User Accounts Deleting User Accounts Circuit Configuration Circuit Group Directory Viewing Circuit Groups Deleting Circuit Groups Adding Circuit GroupsModifying Circuit Groups Communication Settings Serial Port ConfigurationSerial Port Configuration Menu 1. RS232 Port Modes Port Mode Parameters Network Configuration Network Port Parameters Network Parameters Basic Configuration IP Security Basic Configuration Except Net/Mask Pairs Static Route Domain Name Server Snmp Access Parameters Snmp Trap Parameters Ldap Parameters Group Membership Value Type Default = DN Basic Configuration Tacacs Parameters Basic Configuration Radius Parameters WTI-Super=2 WTI-Circuit-Access=0101WTI-Group-Access=111000 Example Email Messaging Parameters Restore Configuration Save User Selected Parameters Ping-No-Answer Fallback Switching Adding Ping-No-Answer Profiles Ping-No-Answer Fallback Switching Deleting Ping-No-Answer Profiles Viewing Ping-No-Answer ProfilesModifying Ping-No-Answer Profiles Alarm Configuration Control Module AUX Connector Output Contacts Output Contacts Over Temperature Alarms Alarm Configuration Defining Ping-No-Answer IP Addresses Ping-No-Answer AlarmConfiguring the Ping-No-Answer Alarm Alarm Configuration Invalid Access Lockout Alarm Alarm Configuration Power Cycle Alarm Monitor/Alarm Input Alarm Configuration Monitor Input Level Settings High Low Alarm Configuration Network Status Screen Status ScreensProduct Status Circuit Status Screen Circuit Group Status Screen Event Logs Audit Log Alarm Log Temperature Log Circuit Control Screen Web Browser Interface A/B Switching Web Browser InterfaceOperation Circuit Group Control Screen Web Browser Interface Operation A/B Switching Text Interface Circuit Status Screen Text Interface TB 2 Enter or /TB Servers Enter 2. A/B Switching Commands Text InterfaceTA 1 Enter or /TA Datacenter Enter TB 1+3+4 Enter +3+4,B Enter B Enter or /T SERVERS,A EnterTA ROUTER,Y or /T 2,B,Y TA 13 Enter Logging Out of Command Mode Manual Operation Enter Telnet & SSH FunctionsSSH Encryption 10-1 Telnet 255.255.255.255 2000 raw Enter Creating an Outbound Telnet ConnectionTelnet ip port raw Enter 10-2 Username Creating an Outbound SSH ConnectionSSH ip -l username Enter SSH 255.255.255.255 -l employee Enter 11-1 ConfigurationSyslog Messages Testing Syslog Configuration 11-2 Snmp Traps 12-1 Testing the Snmp Trap Function 12-2 UserTableuserAccessLevel Account access level AFS-16 Snmp Agent SNMPv3 Authentication and EncryptionConfiguration via Snmp Operation via Snmp Modifying Users Viewing UsersAdding Users Deleting Users Controlling Circuit Groups Circuit Control via SnmpControlling Circuits 13-3 155 Viewing AFS-16 Status via SnmpCircuit Status Unit Environment Status Sending Traps via Snmp 13-5 Setting Up SSL Encryption 14-1 Creating a Self Signed Certificate 14-2 Creating a Signed Certificate 14-3 Downloading the Server Private Key 14-4 15-1 Saving and Restoring Configuration ParametersSending Parameters to a File Restoring Saved Parameters 15-2 Restoring Previously Saved Parameters 15-3 Upgrading AFS-16 Firmware 16-1 16-2 TA * Enter Command Reference GuideCommand Conventions 17-1 Command Summary 17-2 Display Circuit Group Status Screen Command SetDisplay Circuit Status Screen Display Network Status Display Site ID / Unit Information Exit Command ModeLog Functions Connect Toggle to B Position Toggle to a PositionTA 2+3,Y Enter TB 2+3,Y Enter +3,A,Y Enter Toggle CommandSet All Circuits to Default States Send Parameters to File Telnet Outbound Telnet Unlock Port Invalid Access LockoutSend SSH Key Format /TELNET ip port raw Enter Set System Parameters SSH Outbound SSHFormat /SSH ip -l username Enter Set Serial Port Parameters Circuit Group Parameters PNA Configure Ping-No-Answer FunctionAlarm Configuration Parameters Network Port Parameters Test Test Network Parameters Reboot System DefaultUpgrade Firmware Appendix A. Interface Description When connectedWhen not connected Serial Port RS232 Physical/Environmental Appendix B. SpecificationsSwitching Apx-2 Appendix C. Customer Service Apx-3 Apx-4 Trademark and Copyright InformationTrademarks and Copyrights Used in this Manual Index Index-1 Index-2 Radius CLI Index-3 Ldap Index-4 Tacacs Index-5 NTP Index-6 Index-7 Snmp Index-8 SNMPV3