Alarm Configuration | Western Telematic AFS-16-1 specs

Alarm Configuration

•Contact Output Enable: Activates/deactivates the Output Contacts on the Control Module AUX Connector. When the Contact Output Enable parameter is set to "On", the Common line will be switched from the Normally Closed contact to the Normally Open contact. For more information on the Output Contacts, please refer to Section 7.1. (Default = On.)

Note: If either of the "Copy to All Triggers" options is selected, then the Contact Output Enable parameter for other alarms will also be enabled or disabled as specified by this parameter.

•Circuits to Switch: Selects the Circuit Module(s) and Circuit Group(s) that will be switched when the Monitor/Alarm Input feature is triggered, determines the A/B switch position and enables/disables the "Return" feature. This item provides access to a submenu which is used to define the following:

Enable: Enables/disables A/B switching in response to the Monitor/Alarm Input feature. When disabled, the AFS-16 will not perform A/B switching with the Monitor/Alarm Input feature is triggered. (Default = Disable.)

Circuit State: Specifies the A/B position that circuits will be switched to when the Monitor/Alarm Input feature is triggered. (Default = B.)

Return: Enables/Disables the Return feature, which allows the AFS-16 to switch circuits back to their original state after a Monitor/Alarm Input event has been cleared. (Default = On.)

Circuit Access: Determines which Circuit Modules will be switched when the Monitor/Alarm Input feature is triggered. Note that in the Text Interface, Circuit Access is defined via a separate submenu; in the Web Browser Interface, Circuit Access is defined via a drop down menu, which is accessed by clicking on the "plus" sign in the "Configure Circuit Access" field. (Default = undefined.)

Circuit Group Access: Determines which Circuit Group(s) the Monitor/Alarm Input feature will be applied to. Note that in the Text Interface, Circuit Group Access is defined via a separate submenu; in the Web Browser Interface, Circuit Group Access is defined via a drop down menu, which is accessed by clicking on the "plus" sign. (Default = undefined.)

7-11

Image 78

Western Telematic AFS-16-1 manual Alarm Configuration

Contents

AFS-16-1 Shock Hazard Do Not Enter Lithium Battery Secure Racking Two Power Supply Cables Disconnect Power Table of Contents Basic Configuration Telnet & SSH Functions Upgrading AFS-16 Firmware Command Reference Guide List of Figures Vii Security and Co-Location Features Introduction WTI Management Utility Typographic ConventionsEnvironmental Monitoring and Management Bold Font Dual Power Supply Module  Power Switch and on IndicatorUnit Description Control Module Control Module Unit Description Circuit Module Circuit Module Apply Power to the AFS-16 Getting StartedConnect Your PC to the AFS-16 Communicating with the AFS-16 Fallback Switching Fallback Switching Text Interface Fallback Switching Web Browser Interface Hardware Installation Connecting the Power Supply CablesConnecting the Network Cable Connecting a Local Control Device Connecting an External Modem Optional Circuit Module Set Up Module Set UpA/C/B Connectors Control Module SetUp Basic Configuration Communicating with the AFS-16 UnitText Interface Web Browser Interface Access Via PDA Configuration Menus Defining System Parameters Basic Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Log Configuration Web Browser Interface Callback Security Basic Configuration Scripting Options Basic Configuration Command Access Levels User Accounts Granting Circuit Module Access Managing User Accounts Viewing User AccountsAdding User Accounts Basic Configuration Modifying User Accounts Deleting User Accounts Circuit Configuration Circuit Group Directory Viewing Circuit Groups Adding Circuit Groups Modifying Circuit GroupsDeleting Circuit Groups Communication Settings Serial Port ConfigurationSerial Port Configuration Menu 1. RS232 Port Modes Port Mode Parameters Network Configuration Network Port Parameters Network Parameters Basic Configuration IP Security Basic Configuration Except Net/Mask Pairs Static Route Domain Name Server Snmp Access Parameters Snmp Trap Parameters Ldap Parameters Group Membership Value Type Default = DN Basic Configuration Tacacs Parameters Basic Configuration Radius Parameters WTI-Super=2 WTI-Circuit-Access=0101WTI-Group-Access=111000 Example Email Messaging Parameters Restore Configuration Save User Selected Parameters Ping-No-Answer Fallback Switching Adding Ping-No-Answer Profiles Ping-No-Answer Fallback Switching Viewing Ping-No-Answer Profiles Modifying Ping-No-Answer ProfilesDeleting Ping-No-Answer Profiles Alarm Configuration Control Module AUX Connector Output Contacts Output Contacts Over Temperature Alarms Alarm Configuration Ping-No-Answer Alarm Configuring the Ping-No-Answer AlarmDefining Ping-No-Answer IP Addresses Alarm Configuration Invalid Access Lockout Alarm Alarm Configuration Power Cycle Alarm Monitor/Alarm Input Alarm Configuration Monitor Input Level Settings High Low Alarm Configuration Status Screens Product StatusNetwork Status Screen Circuit Status Screen Circuit Group Status Screen Event Logs Audit Log Alarm Log Temperature Log A/B Switching Web Browser Interface OperationCircuit Control Screen Web Browser Interface Circuit Group Control Screen Web Browser Interface Operation A/B Switching Text Interface Circuit Status Screen Text Interface 2. A/B Switching Commands Text Interface TA 1 Enter or /TA Datacenter EnterTB 2 Enter or /TB Servers Enter TB 1+3+4 Enter +3+4,B Enter B Enter or /T SERVERS,A EnterTA ROUTER,Y or /T 2,B,Y TA 13 Enter Logging Out of Command Mode Manual Operation Enter Telnet & SSH FunctionsSSH Encryption 10-1 Telnet 255.255.255.255 2000 raw Enter Creating an Outbound Telnet ConnectionTelnet ip port raw Enter 10-2 Username Creating an Outbound SSH ConnectionSSH ip -l username Enter SSH 255.255.255.255 -l employee Enter Configuration Syslog Messages11-1 Testing Syslog Configuration 11-2 Snmp Traps 12-1 Testing the Snmp Trap Function 12-2 UserTableuserAccessLevel Account access level AFS-16 Snmp Agent SNMPv3 Authentication and EncryptionConfiguration via Snmp Operation via Snmp Modifying Users Viewing UsersAdding Users Deleting Users Controlling Circuit Groups Circuit Control via SnmpControlling Circuits 13-3 155 Viewing AFS-16 Status via SnmpCircuit Status Unit Environment Status Sending Traps via Snmp 13-5 Setting Up SSL Encryption 14-1 Creating a Self Signed Certificate 14-2 Creating a Signed Certificate 14-3 Downloading the Server Private Key 14-4 Saving and Restoring Configuration Parameters Sending Parameters to a File15-1 Restoring Saved Parameters 15-2 Restoring Previously Saved Parameters 15-3 Upgrading AFS-16 Firmware 16-1 16-2 TA * Enter Command Reference GuideCommand Conventions 17-1 Command Summary 17-2 Display Circuit Group Status Screen Command SetDisplay Circuit Status Screen Display Network Status Display Site ID / Unit Information Exit Command ModeLog Functions Connect Toggle to B Position Toggle to a PositionTA 2+3,Y Enter TB 2+3,Y Enter +3,A,Y Enter Toggle CommandSet All Circuits to Default States Send Parameters to File Telnet Outbound Telnet Unlock Port Invalid Access LockoutSend SSH Key Format /TELNET ip port raw Enter Set System Parameters SSH Outbound SSHFormat /SSH ip -l username Enter Set Serial Port Parameters Circuit Group Parameters PNA Configure Ping-No-Answer FunctionAlarm Configuration Parameters Network Port Parameters Reboot System Default Upgrade FirmwareTest Test Network Parameters Appendix A. Interface Description When connectedWhen not connected Serial Port RS232 Physical/Environmental Appendix B. SpecificationsSwitching Apx-2 Appendix C. Customer Service Apx-3 Trademark and Copyright Information Trademarks and Copyrights Used in this ManualApx-4 Index Index-1 Index-2 Radius CLI Index-3 Ldap Index-4 Tacacs Index-5 NTP Index-6 Index-7 Snmp Index-8 SNMPV3