Restoring Saved Parameters, 15-2 | Western Telematic AFS-16-1

Saving and Restoring Configuration Parameters

15.2. Restoring Saved Parameters

This section describes the procedure for using your terminal emulation program to send saved parameters to the AFS-16.

1.Start your terminal emulation program and access the AFS-16’s Text Interface command mode using an account that permits Administrator level commands.

2.Configure your terminal emulation program to upload an ASCII text file.

3.Upload the ASCII text file with the saved AFS-16 parameters. If necessary, key in the file name and directory path.

4.Your terminal emulation program will send the ASCII text file to the AFS-16. When the terminal program is finished with the upload, make certain to terminate the Upload mode.

Note: If the AFS-16 detects an error in the file, it will respond with the "Invalid Parameter" message. If an error message is received, carefully check the contents of the parameters file, correct the problem, and then repeat the Upload procedure.

5.If the parameter upload is successful, the AFS-16 will send a confirmation message, and then return to the command prompt. Type /S and press [Enter], the Status Screen will be displayed. Check the Status Screen to make certain the unit has been configured with the saved parameters.

15-2

Image 110

Western Telematic AFS-16-1 manual Restoring Saved Parameters, 15-2

Contents

AFS-16-1 Shock Hazard Do Not Enter Lithium Battery Secure Racking Two Power Supply Cables Disconnect Power Table of Contents Basic Configuration Telnet & SSH Functions Upgrading AFS-16 Firmware Command Reference Guide List of Figures Vii Security and Co-Location Features Introduction WTI Management Utility Typographic ConventionsEnvironmental Monitoring and Management Bold Font Unit Description Dual Power Supply Module Power Switch and on Indicator Control Module Control Module Unit Description Circuit Module Circuit Module Connect Your PC to the AFS-16 Apply Power to the AFS-16Getting Started Communicating with the AFS-16 Fallback Switching Fallback Switching Text Interface Fallback Switching Web Browser Interface Connecting the Network Cable Hardware InstallationConnecting the Power Supply Cables Connecting a Local Control Device Connecting an External Modem Optional Circuit Module Set Up Module Set UpA/C/B Connectors Control Module SetUp Text Interface Basic ConfigurationCommunicating with the AFS-16 Unit Web Browser Interface Access Via PDA Configuration Menus Defining System Parameters Basic Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Log Configuration Web Browser Interface Callback Security Basic Configuration Scripting Options Basic Configuration Command Access Levels User Accounts Granting Circuit Module Access Adding User Accounts Managing User AccountsViewing User Accounts Basic Configuration Modifying User Accounts Deleting User Accounts Circuit Configuration Circuit Group Directory Viewing Circuit Groups Deleting Circuit Groups Adding Circuit GroupsModifying Circuit Groups Communication Settings Serial Port ConfigurationSerial Port Configuration Menu 1. RS232 Port Modes Port Mode Parameters Network Configuration Network Port Parameters Network Parameters Basic Configuration IP Security Basic Configuration Except Net/Mask Pairs Static Route Domain Name Server Snmp Access Parameters Snmp Trap Parameters Ldap Parameters Group Membership Value Type Default = DN Basic Configuration Tacacs Parameters Basic Configuration Radius Parameters WTI-Super=2 WTI-Circuit-Access=0101WTI-Group-Access=111000 Example Email Messaging Parameters Restore Configuration Save User Selected Parameters Ping-No-Answer Fallback Switching Adding Ping-No-Answer Profiles Ping-No-Answer Fallback Switching Deleting Ping-No-Answer Profiles Viewing Ping-No-Answer ProfilesModifying Ping-No-Answer Profiles Alarm Configuration Control Module AUX Connector Output Contacts Output Contacts Over Temperature Alarms Alarm Configuration Defining Ping-No-Answer IP Addresses Ping-No-Answer AlarmConfiguring the Ping-No-Answer Alarm Alarm Configuration Invalid Access Lockout Alarm Alarm Configuration Power Cycle Alarm Monitor/Alarm Input Alarm Configuration Monitor Input Level Settings High Low Alarm Configuration Network Status Screen Status ScreensProduct Status Circuit Status Screen Circuit Group Status Screen Event Logs Audit Log Alarm Log Temperature Log Circuit Control Screen Web Browser Interface A/B Switching Web Browser InterfaceOperation Circuit Group Control Screen Web Browser Interface Operation A/B Switching Text Interface Circuit Status Screen Text Interface TB 2 Enter or /TB Servers Enter 2. A/B Switching Commands Text InterfaceTA 1 Enter or /TA Datacenter Enter TB 1+3+4 Enter +3+4,B Enter B Enter or /T SERVERS,A EnterTA ROUTER,Y or /T 2,B,Y TA 13 Enter Logging Out of Command Mode Manual Operation Enter Telnet & SSH FunctionsSSH Encryption 10-1 Telnet 255.255.255.255 2000 raw Enter Creating an Outbound Telnet ConnectionTelnet ip port raw Enter 10-2 Username Creating an Outbound SSH ConnectionSSH ip -l username Enter SSH 255.255.255.255 -l employee Enter 11-1 ConfigurationSyslog Messages Testing Syslog Configuration 11-2 Snmp Traps 12-1 Testing the Snmp Trap Function 12-2 UserTableuserAccessLevel Account access level AFS-16 Snmp Agent SNMPv3 Authentication and EncryptionConfiguration via Snmp Operation via Snmp Modifying Users Viewing UsersAdding Users Deleting Users Controlling Circuit Groups Circuit Control via SnmpControlling Circuits 13-3 155 Viewing AFS-16 Status via SnmpCircuit Status Unit Environment Status Sending Traps via Snmp 13-5 Setting Up SSL Encryption 14-1 Creating a Self Signed Certificate 14-2 Creating a Signed Certificate 14-3 Downloading the Server Private Key 14-4 15-1 Saving and Restoring Configuration ParametersSending Parameters to a File Restoring Saved Parameters 15-2 Restoring Previously Saved Parameters 15-3 Upgrading AFS-16 Firmware 16-1 16-2 TA * Enter Command Reference GuideCommand Conventions 17-1 Command Summary 17-2 Display Circuit Group Status Screen Command SetDisplay Circuit Status Screen Display Network Status Display Site ID / Unit Information Exit Command ModeLog Functions Connect Toggle to B Position Toggle to a PositionTA 2+3,Y Enter TB 2+3,Y Enter +3,A,Y Enter Toggle CommandSet All Circuits to Default States Send Parameters to File Telnet Outbound Telnet Unlock Port Invalid Access LockoutSend SSH Key Format /TELNET ip port raw Enter Set System Parameters SSH Outbound SSHFormat /SSH ip -l username Enter Set Serial Port Parameters Circuit Group Parameters PNA Configure Ping-No-Answer FunctionAlarm Configuration Parameters Network Port Parameters Test Test Network Parameters Reboot System DefaultUpgrade Firmware Appendix A. Interface Description When connectedWhen not connected Serial Port RS232 Physical/Environmental Appendix B. SpecificationsSwitching Apx-2 Appendix C. Customer Service Apx-3 Apx-4 Trademark and Copyright InformationTrademarks and Copyrights Used in this Manual Index Index-1 Index-2 Radius CLI Index-3 Ldap Index-4 Tacacs Index-5 NTP Index-6 Index-7 Snmp Index-8 SNMPV3