On/Off Switch | Xantrex Technology PV100S-208 specs

Operator Interface Controls

WARNING: Shock Hazard

Disengaging the main enclosure door interlock switch does NOT remove all hazardous voltages from inside the inverter. Before attempting to service the PV100S, follow the de-energize Lockout and Tag procedure on page 5–3.

On/Off Switch

The PV100S incorporates a maintained position ON/OFF switch located on the front door of the main enclosure. Under normal conditions, the ON/OFF switch is in the ON position. Turning the switch to the OFF position will initiate an immediate controlled shutdown of the PV100S and open both the main AC and DC contactors within the unit. The main AC and DC contactors cannot be closed unless the switch is in the ON position. The PV100S is prevented from being restarted until the ON/OFF switch is turned back to the ON position.

WARNING: Shock Hazard

Turning the ON/OFF switch to the OFF position does NOT remove all hazardous voltages from inside the inverter. Before attempting to service the PV100S, follow the de-energize Lockout and Tag procedure on page 5–3.

Figure 1-7On/Off Switch

152379 Rev C

1–11

Image 33

Xantrex Technology PV100S-208 manual On/Off Switch, Operator Interface Controls

Contents

PV100S 100 kW Grid-Tied Photovoltaic Inverter Page PV100S 100 kW Grid-Tied Photovoltaic Inverter Date and Revision Scope PurposeAudience Organization Following conventions are used in this guide Conventions Used Related Information Abbreviations and AcronymsPage Important Safety Instructions Personal Safety General Safety PrecautionsSafety Equipment Wiring Requirements Safety Lockout and Tag Operational Safety Procedures De-Energize/Isolation Procedure Interconnection Standards ComplianceTo isolate the PV100S Xii Contents Operation Troubleshooting Preventative MaintenanceCommissioning Specifications Figures Figures Tables Page Introduction Fixed Unity Power Factor Operation Operation Features Peak Power Tracking 1Maximum Peak Power Tracking Utility Voltage/Frequency Fault Automatic Reset PV Ground Fault Detection Safety FeaturesAnti-Island Protection DC Over-voltage Detection 2PV100S Major Components Physical Characteristics Power Electronics Matrix Power Distribution PanelMain Inverter Enclosure Inductor Enclosure DC Interface Enclosure Transformer EnclosureAC Interface Enclosure 4AC Interface Enclosure and Transformer Enclosure Communications Enclosure Operator Interface Controls Main Enclosure Door Interlock Switch Operator Interface Controls On/Off Switch AC and DC Disconnect Switches Communication Features System Status and Fault Reporting Data logging features includeData Logging Universal Front Panel Control Unit Ufcu Communication Methods 10PC Connections in the Communications Enclosure PC Connection Methods Wireless Access Pots Access Direct Access Ethernet LAN Access Specific list of available parameters GUI Software Features Operation Faults Description of System OperationOverview 1Operating States Flow Chart Power Tracking Operating StatesTransition Shutdown FaultManual Current Matrix Test Ufcu Keypad Operation and LCD Display Operator Interface Standard Display LCD Display Initialization Screen Menu Structure 4Operator Interface Menu Diagram To Display Any Operational Value in the Read Menu Read Menu 5Scrolling through the Read Menu 2Read Menu Descriptions Shut Down Sleep READ-by-ID To use the Read-by-ID Feature 3Data Logging Menu Write Menu To change Write Menu parameters Changing and Displaying Write Menu Parameter Values Minimum Grid Time Delay for PV Enable Peak Power To change the Goal State Commanding Goal State Changes To change the Date and Time Setting the Date and Time Manual State Transitions Shutdown → Power Tracking → ShutdownAutomatic State Transitions Shutdown → Matrix Test → Shutdown Auto-restart Feature Any State → FaultTo clear the fault Energize Procedure Startup De-Energize/Isolation Procedure ShutdownTo start up the PV100S 9GUI Interface Main Menu Screen Computer Communications with the PV100S Starting the Software Setup Program Installing the Graphic User Interface GUI SoftwareStarting the Setup Program Using Autorun Starting Setup Manually 10Starting Setup from a Command Prompt Starting Setup From a Command Prompt To continue with the GUI software installation Model Specific Software Installation 13GUI Setup Start Window 15GUI Setup Progress Indicator Window Remote/LAN Connection Running the GUI 18GUI Interface Screen if Connected Directly Direct Connection To configure the inverters in the GUI GUI Configuration Adding Inverters 21Operational Configuration Screen Limits 23Operational Configuration Screen Power Tracker 26Connection Configuration Screen General 27GUI Help Topics GUI HelpPage Commissioning Commissioning Procedure Starting the Commissioning Test FileTo commission the PV100S Serial Number Verify AC VoltageVerify DC Voltage Inspect Inductor Enclosure Apply Grid VoltageFront Panel Display Confirm AC Operational Parameters Establish Communications with the GUI Confirm Power Tracker Configuration Operational Parameters Confirm DC Operational ParametersVerify Door Interlock Functions Thank You for choosing Xantrex The Smart Choice for Power Operate InverterCompleted Commissioning Page Troubleshooting Faults and Fault Codes General TroubleshootingRespond to any PV100S alarm or fault as follows 1LCD showing Fault Code Clearing Faults Manually 1Fault Codes Fault Code Descriptions Fault Code Descriptions 1Fault Codes Internal RAM error 1Fault Codes 1Fault Codes Fpga PreventativeMaintenance Maintenance Safety Operational Safety ProceduresDe-Energize/Isolation Procedure Lockout and Tag TB4-A 3PV Terminal Locations Monthly Intervals or As Required Periodic Maintenance Enclosure Seals Six-month IntervalsElectrical Connections Inductor EnclosurePage Specifications Environmental Specifications System Specifications Over Voltage, Under Voltage and Frequency Ranges Electrical Specifications TB2 Wire Gauge and Torque Requirements Figure A-1Electrical Diagram sample Schematics Appendix a Schematics Appendix a Schematics Appendix a This page intentionally left blank Xantrex Limited Warranty Warranty and Product Information Product Disclaimer Product Registration Warranty and Return WA-4 Rev C Index IX-2 Rev C Page Xantrex Technology Inc