Xantrex Technology PV100S-208 specification

Computer Communications with the PV100S

Starting Setup From a Command Prompt

To start the program from a command prompt:

1.Insert the XANTREX SOLAR INVERTER GUI – INSTALLATION CD into your CDROM drive.

2.Click on START and select “RUN”.

3.Enter the drive letter assigned to your CDROM and the name of the installation program as shown in Figure 2-10.

Figure 2-10Starting Setup from a Command Prompt

Important: The drive letter assigned to your CDROM may be different from the one shown in Figure 2-10.Be sure to use the correct letter for your drive or the program will not start.

4.Click OK. The splash screen shown in Figure 2-11will appear.

5.Proceed to the Model Specific Software Installation section on page 2–28to continue with the installation.

152379 Rev C

2–27

Image 67

Xantrex Technology PV100S-208 manual Starting Setup From a Command Prompt, 10Starting Setup from a Command Prompt

Contents

PV100S 100 kW Grid-Tied Photovoltaic Inverter Page PV100S 100 kW Grid-Tied Photovoltaic Inverter Date and Revision Organization PurposeScope Audience Following conventions are used in this guide Conventions Used Related Information Abbreviations and AcronymsPage Important Safety Instructions Wiring Requirements General Safety PrecautionsPersonal Safety Safety Equipment Safety Lockout and Tag Operational Safety Procedures Interconnection Standards Compliance De-Energize/Isolation ProcedureTo isolate the PV100S Xii Contents Operation Preventative Maintenance TroubleshootingCommissioning Specifications Figures Figures Tables Page Introduction Fixed Unity Power Factor Operation Operation Features Peak Power Tracking 1Maximum Peak Power Tracking Utility Voltage/Frequency Fault Automatic Reset DC Over-voltage Detection Safety FeaturesPV Ground Fault Detection Anti-Island Protection 2PV100S Major Components Physical Characteristics Inductor Enclosure Power Distribution PanelPower Electronics Matrix Main Inverter Enclosure Transformer Enclosure DC Interface EnclosureAC Interface Enclosure 4AC Interface Enclosure and Transformer Enclosure Communications Enclosure Operator Interface Controls Main Enclosure Door Interlock Switch Operator Interface Controls On/Off Switch AC and DC Disconnect Switches Communication Features Data logging features include System Status and Fault ReportingData Logging Universal Front Panel Control Unit Ufcu Communication Methods 10PC Connections in the Communications Enclosure PC Connection Methods Wireless Access Pots Access Direct Access Ethernet LAN Access Specific list of available parameters GUI Software Features Operation Description of System Operation FaultsOverview 1Operating States Flow Chart Operating States Power TrackingTransition Matrix Test FaultShutdown Manual Current Ufcu Keypad Operation and LCD Display Operator Interface Standard Display LCD Display Initialization Screen Menu Structure 4Operator Interface Menu Diagram To Display Any Operational Value in the Read Menu Read Menu 5Scrolling through the Read Menu 2Read Menu Descriptions Shut Down Sleep READ-by-ID To use the Read-by-ID Feature 3Data Logging Menu Write Menu To change Write Menu parameters Changing and Displaying Write Menu Parameter Values Minimum Grid Time Delay for PV Enable Peak Power To change the Goal State Commanding Goal State Changes To change the Date and Time Setting the Date and Time Shutdown → Matrix Test → Shutdown Shutdown → Power Tracking → ShutdownManual State Transitions Automatic State Transitions Any State → Fault Auto-restart FeatureTo clear the fault De-Energize/Isolation Procedure Shutdown Energize Procedure StartupTo start up the PV100S 9GUI Interface Main Menu Screen Computer Communications with the PV100S Starting Setup Manually Installing the Graphic User Interface GUI SoftwareStarting the Software Setup Program Starting the Setup Program Using Autorun 10Starting Setup from a Command Prompt Starting Setup From a Command Prompt To continue with the GUI software installation Model Specific Software Installation 13GUI Setup Start Window 15GUI Setup Progress Indicator Window Remote/LAN Connection Running the GUI 18GUI Interface Screen if Connected Directly Direct Connection To configure the inverters in the GUI GUI Configuration Adding Inverters 21Operational Configuration Screen Limits 23Operational Configuration Screen Power Tracker 26Connection Configuration Screen General 27GUI Help Topics GUI HelpPage Commissioning Starting the Commissioning Test File Commissioning ProcedureTo commission the PV100S Verify AC Voltage Serial NumberVerify DC Voltage Apply Grid Voltage Inspect Inductor EnclosureFront Panel Display Confirm AC Operational Parameters Establish Communications with the GUI Confirm DC Operational Parameters Confirm Power Tracker Configuration Operational ParametersVerify Door Interlock Functions Operate Inverter Thank You for choosing Xantrex The Smart Choice for PowerCompleted Commissioning Page Troubleshooting General Troubleshooting Faults and Fault CodesRespond to any PV100S alarm or fault as follows 1LCD showing Fault Code Clearing Faults Manually 1Fault Codes Fault Code Descriptions Fault Code Descriptions 1Fault Codes Internal RAM error 1Fault Codes 1Fault Codes Fpga PreventativeMaintenance Operational Safety Procedures Maintenance SafetyDe-Energize/Isolation Procedure Lockout and Tag TB4-A 3PV Terminal Locations Monthly Intervals or As Required Periodic Maintenance Inductor Enclosure Six-month IntervalsEnclosure Seals Electrical ConnectionsPage Specifications Environmental Specifications System Specifications Over Voltage, Under Voltage and Frequency Ranges Electrical Specifications TB2 Wire Gauge and Torque Requirements Figure A-1Electrical Diagram sample Schematics Appendix a Schematics Appendix a Schematics Appendix a This page intentionally left blank Xantrex Limited Warranty Warranty and Product Information Product Disclaimer Product Registration Warranty and Return WA-4 Rev C Index IX-2 Rev C Page Xantrex Technology Inc