Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology PV100S-208 1 Fault Codes, Error, Fault Type, Fault Sources, Fault Description

Models: PV100S-208

1 124

Download 124 pages 2.86 Kb

Page 95

					Fault Code Descriptions

Table 4-1Fault Codes

Error		Fault Type
Error		H=Hardware
Code	Fault Source(s)	S=Software	Fault Description	Possible Causes

XX62	Matrix Temperature	S	This fault indicates that the PV100S	• Fuses F15 or F16 blown
			has detected that the temperature of	•	External cooling fan
			the IGBT matrix aluminum heatsink		inoperable
			has exceeded the maximum allowed	• Air flow on heat sink
			value of 95 °C.		impeded due to
					accumulation of debris
				•	Operation above rated
					ambient temperature for
					an extended period of
					time

0070	Interlock Activated	H	This fault indicates that the PV100S	• Door is open and
			has detected that the door of the Main		interlock switch is
			Inverter enclosure is open and the		active
			door interlock switch is in the active	•	Interlock switch is
			position. This fault is primarily for		inoperable
			personnel safety. Opening the door of	• P2 or P3 on CCU2 is
			the Main Inverter enclosure while the		loose or disconnected
			PV100S is processing power will	•	CCU2 +/-15Vdc Power
			cause an immediate orderly shutdown		Supply is defective
			of the system.

0071	PV Switch Open	H	This fault indicates that the PV100S	• DC disconnect switch is
			has detected that the DC disconnect		open and auxiliary
			switch (S2) is open and the auxiliary		switch is active
			switch is in the active position. This	•	Auxiliary switch is
			fault is primarily for personnel safety.		inoperable
			Opening the DC disconnect switch	• P2 or P3 on CCU2 is
			while the PV100S is processing		loose or disconnected
			power will cause an immediate	• CCU2 +/-15 Vdc Power
			orderly shutdown of the system.		Supply is defective

0074	Fused PV Contactor	S	This fault indicates that the PV100S	•	K2 is inoperable
			has detected that upon system	•	SSR2 is inoperable
			shutdown, the DC bus voltage has
			remained within 5% of the DC input
			voltage for more than 10 seconds.
			This condition is indicative of a fused
			PV contactor (K2).

152379 Rev C

4–9

Image 95

Xantrex Technology PV100S-208 manual 1 Fault Codes, Error, Fault Type, Fault Sources, Fault Description, Possible Causes

Contents

PV100S-208 PV100S-480 Operation and Maintenance ManualPV100S 100 kW Grid-Tied Photovoltaic Inverter Page PV100S 100 kW Grid-Tied Photovoltaic Inverter Operation and Maintenance ManualDisclaimer About XantrexTrademarks Notice of CopyrightAudience About This ManualPurpose ScopeConventions Used Related Information Abbreviations and AcronymsPage WARNING Lethal Voltage Important Safety InstructionsSAVE THESE INSTRUCTIONS - DO NOT DISCARD WARNING Shock HazardWiring Requirements General Safety PrecautionsPersonal Safety Safety EquipmentCAUTION Fire Hazard WARNING Shock Hazard Operational Safety ProceduresLockout and Tag To isolate the PV100S De-Energize/Isolation ProcedureInterconnection Standards Compliance Page 1 Introduction ContentsAutomatic Sleep Test 2 OperationFaults Manual CurrentFaults and Fault Codes General Troubleshooting 4 Troubleshooting5 Preventative Maintenance 3 CommissioningA Specifications Figures Figure 2-24 Connection Configuration Screen - General - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-35 Figure 2-25 Connection Configuration Screen - Telephone Fault Configuration - - - - - - - - - - - - - -2-36 Figure 2-26 Connection Configuration Screen - General - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-36 Figure 2-27 GUI Help Topics - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-37 Figure 4-1 LCD showing Fault Code - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3 Figure 5-1 Inverter AC Terminal Locations in the Main Inverter Enclosure - - - - - - - - - - - - - - - - 5-4 Figure 5-2 Utility AC Terminal Connections in the AC Interface Enclosure - - - - - - - - - - - - - - - - 5-4 Figure 5-3 PV Terminal Locations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-5 Figure A-1 Electrical Diagram sample- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A-5 Figure A-2 PV100S-480 Schematic for Main Power Distribution 152316 E1 - - - - - - - - - - - - - - A-6 Figure A-3 PV100S-480 Schematic for Control Power Distribution 152316 E2 - - - - - - - - - - - - - A-7 Figure A-4 PV100S-480 Schematic for Converter Control Unit 152316 E3- - - - - - - - - - - - - - - - A-8 Figure A-5 PV100S-208 Schematic Main Power Distribution 152376 C1 - - - - - - - - - - - - - - - - - A-9 Figure A-6 PV100S-208 Schematic for Control Power Distribution 152376 C2 - - - - - - - - - - - - A-10 Figure A-7 PV100S-208 Schematic for Converter Control Unit 152376 C3- - - - - - - - - - - - - - - A-11 Tables Page 1 Introduction Fixed Unity Power Factor Operation Operation FeaturesPeak Power Tracking Figure 1-1 Maximum Peak Power Tracking Utility Voltage/Frequency Fault Automatic ResetDC Over-voltage Detection Safety FeaturesPV Ground Fault Detection Anti-Island ProtectionPhysical Characteristics Inductor Enclosure Power Distribution PanelPower Electronics Matrix Main Inverter EnclosureAC Interface Enclosure DC Interface EnclosureCAUTION Equipment Damage Transformer EnclosureFigure 1-5 PC Connections in the Communications Enclosure Communications EnclosureFigure 1-4 AC Interface Enclosure and Transformer Enclosure Operator Interface Controls Main Enclosure Door Interlock SwitchWARNING Shock Hazard On/Off SwitchFigure 1-7 On/Off Switch WARNING Shock HazardAC and DC Disconnect Switches Communication FeaturesThe Data logging features include System Status and Fault ReportingData Logging Universal Front Panel Control Unit UFCU Communication MethodsPC Connection Methods Figure 1-11 POTS Access POTS AccessWireless Access Figure 1-14 Direct Access Ethernet LAN AccessDirect Access Figure 1-13 Ethernet LAN Accesspage 2-16 for a specific list of available parameters GUI Software Featuresspecific list of available parameters 2 Operation Overview FaultsDescription of System Operation 152379 Rev C Figure 2-1 Operating States Flow ChartPOWER UP Description of System OperationTransition Power TrackingOperating States Matrix Test FaultShutdown Manual CurrentUFCU Keypad Operation and LCD Display Operator InterfaceStandard Display LCD Display - Initialization ScreenMenu Structure Table 2-1 Scrolling through the Read Menu Parameters READ MenuTo Display Any Operational Value in the READ Menu 152379 Rev C Figure 2-5 Scrolling through the Read MenuOperation 2-10Units Table 2-2 Read Menu DescriptionsOperational Parameter DescriptionUnits Table 2-2 Read Menu DescriptionsOperational Parameter DescriptionTo use the Read-by-ID Feature READ-by-IDTable 2-4 provides a list of the Accumulated Values Menu parameters Table 2-3 Data Logging MenuAccumulated Values Menu Table 2-3 provides a list of the Data Logging Menu parametersWRITE Menu To change WRITE Menu parameters Changing and Displaying WRITE Menu Parameter ValuesMin AC Freq Table 2-5 Write Menu ParametersMin AC Volts% Max AC FreqTable 2-5 Write Menu Parameters Time Delay for PVPPT Enable Enable Peak PowerPower Tracker Rate Power Tracker StepTo change the Goal State Commanding Goal State ChangesTo change the Date and Time Setting the Date and TimeAutomatic State Transitions Power Tracking → Manual Current → Power Tracking or ShutdownShutdown → Power Tracking → Shutdown Manual State TransitionsAny State → Fault Auto-restart FeatureTo isolate the PV100S Energize Procedure StartupDe-Energize/Isolation Procedure Shutdown To start up the PV100SComputer Communications with the PV100S Starting Setup Manually Installing the Graphic User Interface GUI SoftwareStarting the Software Setup Program Starting the Setup Program Using AutorunStarting Setup From a Command Prompt To continue with the GUI software installation Model Specific Software Installation2. Click OK and the following window will appear 2-30 Figure 2-15 GUI Setup Progress Indicator WindowFigure 2-16 GUI Setup Start Window OperationRemote/LAN Connection Running the GUI2-32 Direct ConnectionFigure 2-18 GUI Interface Screen if Connected Directly OperationTo configure the inverters in the GUI GUI Configuration - Adding Invertersa Fill out Operational Limits Information requested e Fill out the Power Tracking Information requested 9. Click on the Telephone Configuration sub-menu to continue Figure 2-26 Connection Configuration Screen - GeneralGUI Help 2-38 3 Commissioning To commission the PV100S Commissioning ProcedureStarting the Commissioning Test File Verify DC Voltage Serial NumberVerify AC Voltage Front Panel Display Inspect Inductor EnclosureApply Grid Voltage Confirm AC Operational Parameters Establish Communications with the GUIMatrix Test Confirm Power Tracker Configuration Operational ParametersConfirm DC Operational Parameters Verify Door Interlock FunctionsThank You for choosing Xantrex The Smart Choice for Power Operate InverterCompleted Commissioning Page 4 Troubleshooting WARNING Lethal Voltage Faults and Fault CodesGeneral Troubleshooting Respond to any PV100S alarm or fault as followsClearing Faults Manually Table 4-1 Fault Codes Fault Code DescriptionsFault Code Descriptions Table 4-1 Fault CodesFault Sources Table 4-1 Fault CodesError Fault TypeCPU error Table 4-1 Fault CodesInternal RAM error Fault Sources Table 4-1 Fault CodesError Fault TypeFault Sources Table 4-1 Fault CodesError Fault TypeFault Sources Table 4-1 Fault CodesError Fault Type5 PreventativeMaintenance WARNING Shock Hazard Maintenance SafetyOperational Safety Procedures De-Energize/Isolation ProcedureWARNING Shock Hazard Lockout and TagB phase Enlargement of Terminal Connectors in the AC Interface EnclosureA phase C phaseGrouND TB3-3 PV NEGative Cable TB3-2 PV POSitive Cable TB3-1 Figure 5-3 PV Terminal LocationsMaintenance Safety 152379 Rev CFan Operation Periodic MaintenanceMonthly Intervals or As Required Aluminum Extrusion HeatsinkInductor Enclosure Six-month IntervalsEnclosure Seals Electrical ConnectionsPage A Specifications CAUTION Equipment Damage System SpecificationsEnvironmental Specifications Table A-2 provides the AC and DC specifications for the PV100S Electrical SpecificationsOver Voltage, Under Voltage and Frequency Ranges Table A-3 Over/Under Voltage and Over/Under Frequency RangesTable A-5 DC Terminal Wire Gauge, Bolt Size, and Torque Values Wire Gauge and Torque RequirementsTable A-4 AC Terminal Wire Gauge, Bolt Size, and Torque Values Schematics Figure A-1 Electrical Diagram sampleAppendix A 152379 Rev CAppendix A Figure A-2 PV100S-480 Schematic for Main Power Distribution 152316 E1Schematics 152379 Rev C152379 Rev C SchematicsAppendix A Appendix A Figure A-4 PV100S-480 Schematic for Converter Control Unit 152316 E3Schematics 152379 Rev C152379 Rev C Figure A-5 PV100S-208 Schematic Main Power Distribution 152376 C1Schematics Appendix AAppendix A A-10Schematics 152379 Rev C152379 Rev C Figure A-7 PV100S-208 Schematic for Converter Control Unit 152376 C3Schematics Appendix A152379 Rev C A-12Schematics This page intentionally left blank3. What does this warranty not cover? Warranty and Product InformationXantrex Limited Warranty 1. What does this warranty cover and how long does it last?7. WARNING LIMITATIONS ON USE 4. Product Disclaimer5. Limitations to Product Disclaimer 6. Information Disclaimer925 455 PRODUCT REGISTRATIONAttention Customer Service Fax number152379 Rev C Warranty and ReturnWA-4 Index Page Page 152379 Rev C Xantrex Technology Inc1 800 670 0707 Tel toll free NA 1 360 925 5097 Tel direct 1 800 994 7828 Fax toll free NA