Graphic Djde points to note | Xerox FreeFlow manual

Using Dynamic Job Descriptor Entries (DJDEs)

GRAPHIC DJDE: points to note

•Other than name, none of the parameters may be used if the specified graphic is document interleaved, nor should name normally be used if the graphic is referenced by an IMAGE DJDE.

If the graphic is page interleaved, the remaining parameters may be used exactly as on the IMAGE DJDE (except for the T parameter). If these parameters are specified in the GRAPHIC DJDE and also on one or more IMAGE DJDEs that reference the same graphic, the graphic is imaged on the page once for each reference.

•Document and page interleaved graphics: If no textual data has been previously encountered, the graphic specified in the GRAPHIC DJDE is document interleaved and is copied to a .IMG type disk file.

If textual data has been encountered previously, the graphic is page interleaved and the previous print record should have caused a page transition. If not, the occurrence of this DJDE forces an immediate page termination, and the next print record encountered is processed relative to TOF (Top of Form) on the next physical page.

An interleaved graphic that immediately follows a header banner page is treated as document interleaved. The header banner page must be defined by a BANNER command. Skip carriage control commands on a graphics sentinel DJDE are ignored.

•Graphic file replacement and deletion: If an image file with the specified name already exists in the “lcds” resources directory, it is superseded by the new one. However, it is not replaced immediately. If a new file will be retained beyond the scope of the current report processing (as indicated by the OUTPUT PURGE parameter or the SAVE DJDE), the new file is stored in (and replaces existing files in) the “lcds” resource folder when processing of the report is complete.

NOTE: The “lcds” folder can be accessed from either of the following Unix directory paths:

/var/spool/XRXnps/resources/lcds/ or

/opt/XRXnps/resources/lcds/

Using LCDS Print Description Language

5-41

Image 395

Xerox FreeFlow manual Graphic Djde points to note

Contents

Using Lcds Page Table of contents Specifying input parameters Page Page Using logical processing Page Specifying print format parameters Page Using Dynamic Job Descriptor Entries DJDEs Page Gdata Djde Graphic Djde Using PDL commands for graphics Using Lcds Print Description Language Table of contents Xvi Using Lcds Print Description Language Ozone information U. S. only Laser safety Operation safety U. S Electrical supply Operation safety Europe Ventilation Operator accessible areas CE mark Europe only MaintenanceBefore cleaning your product For further information Introduction Contents Conventions Line DATA=1,132, FONTINDEX=133 Introduction Xxvi Using Lcds Print Description Language PDL principles and procedures Enabling PDL features and functions Components of a command PDL command structure and componentsCommand lines VFU1 ASSIGN= TOF= BOF= CME4 LINE= POSITION= FONT= Set of typical PDL commands CME4 CME VFU1 VFUEND Keywords String constants Variable referencesExample Value constants T1 Table CONSTANT= Using the # character case toggleUsing a repeat count T1 Table CONSTANT=3 Ascii Iden PREFIX=XC1C2C3C4Iden PREFIX=AABC!44EF Iden PREFIX=X414243444546 Record Iden PREFIX=DJDECONSTANT=ABCDE Iden PREFIX=EABC!C4EFG Constant = H6’373737’ Block Valid structure for FreeFlow Print Server Lcds systems Command syntaxSyntax rules Incorrect structure for FreeFlow Print Server Lcds systems OTEXT=‘load blue paper’, Wait END ENDCriteria CONSTANT=0,120,EQ,T1 OTEXT=sc ,passnumEND,WAITNONE Output Command syntax conventionsLine Syntax conventions Sample PDL commands PDL command categories Job Source Library JSL What does a JSL specify? JSL command levels Jobs and catalogs within the JSL Command levels and their general purposeOther commands in the JSL can reference them. Commands with Sample JSL file format Jdlsef JDL JDL or system level commandsCoding system level commands with identifiers JDL name Xsml JDL CONSTANT=JOB VFU2VFU3 CONSTANT=PAGE Tables Coding other system level commands Acct USER=TRAY Volume HOST=IBMONL, CODE=EBCDIC Record LENGTH=136Specifying Acct command parameters Line DATA=1,132, PCCTYPE=IBM3211 PCC=0,NOTRAN, VFU=VFU1 Job or JDE level commands Catalog level commandsPower Catalog JOB1 JDE INCLUDE=POWER JOB4 JDE Line VFU=VFU2 Output FORMS=AY2F Coding job or JDE level commandsJOB2 JDE JOB3 JDE PURGE=NO Job level commandsMessage OTEXT= ALL Forms Duplex ONLY!!!, 1, Wait Examples Nested comment System commands are coded hereEnding a JSL What may follow the END command Comments FONTS=P1012A, PMODE=PORTRAIT Sample completed JSLXrxspl JDL VFU2UP Before creating a JSL considerations and decisions DATA=1,132, PCCTYPE=IBM3211 Input data Output specifications Special features Paper sizes and page frames Interactions between JSLs, catalogs, and jobs Orientation Vertical and horizontal positions in portrait mode Layout for FMT6 Impact printer format, 8.1 lines per inch Page Fixed pitch and proportional font character Spacing Overriding PDL commands Command override sequence Print Services window with Queue Manager Selected Page PDL principles and procedures Example IDR1 ILIST=’RED’,’BLACK’,’PINK’ Sample JSLJdlhlc JDL PDE1 BEGIN=175 DOTS, 00 Xdots Hints and tips CONSTANT=2,132,EQ,T1 Smplst JDL VFUCONSTANT= Criteria Coding a JSL Before you start Short JSL coding procedure Workspace and Programs menus 10. Text Editor window Opt/XRXnps/resources/lcds Var/spool/XRXnps/resources/lcds 11. Text Editor Include a File window 12. Save As window Recommended 13. Workspace and Programs menus Full JSL coding procedure 14. Text Editor window Recommended JDE INCLUDE=CATPOW 16. Text Editor Save As window 10. Sample online JSL Sample online JSL Both JOB CONSTANT=// JOBHdrp JOB Banner TEST=C1, HCOUNT=2, TCOUNT=0 Trlp JOB Banner TEST=C2, HCOUNT=0, TCOUNT=3 11. Sample offline JSL Sample offline JSL IDR=IDR1, NUMBER=1,1,0,1,’BLACK’ LTHFLD=2, FORMAT=BIN, OFFSET=0 Compiling a JSL Compiling procedure 18. Selecting Tools from the Workspace menu 19. Terminal window with % prompt displayed = / foldername1 / foldername2 12. xjdc command options Opt/XRXnps/XRXxjdc/data Files produced by the compilation procedure JSL Contains Errors Correcting errors in a JSL Opt/XRXnps/resources/lcds 21. Text Editor Open a File window 22. a .LST file for a JSL containing errors Dynamic job descriptor entries DJDEs Benefits of using DJDEs Starting and ending online dump sessions Online dump format and contentDumps Online dump Restrictions for online dumps 13. Print format command usage for online dump Starting and ending tape dump sessions Offline dump format and contentOffline dump Page DP92C 14. Software version compatibility 15. Highlight color commands XMP IresultLogo Number Other Xerox monochrome LPS jobs Points to note for colored formsPage Input data streams Specifying input parameters Input processing online Input processing functions Using Downloading resource files from the host to the printer IBM Default channel assignments made at installation CONSTANT=’TRAILER PAGE’ Example of an online JSLOnline JDL VFU1 MASK=?, CONSTANT=HE?DE? Dflt JOB CONSTANT=’EOJ’CONSTANT=’//JOB’ Host computer tape formats Input processing offline Record formats Tape codesPacked data formats Record structure Multivolume processing Summary of PDL commands associated with input Processing Input processing command descriptions Summary of Block command parameters Block commandBlock command parameters Block Constant Block AdjustDefault Options Block Length parameter options and definitions Block FormatOptions Block Format parameter options and definitions Block Length Options 10. Block Lthfld parameter options and definitions Block LmultOptions Block Lmult parameter options and definitions Block Lthfld Options 11. Block Offset parameter options and definitions Point to noteBlock Offset Syntax Block Zero Default noBlock Postamble parameter points to note Block Preamble Block LENGTH=351, OFFSET=2 ADJUST=0 LTHFLD=2, PREAMBLE=8 Block command points to noteBlock command example Code Assign Code command parameters15. Summary of Code command parameters Code Default Options 16. Code Assign parameter options and definitions Code DefaultCode Assign Examples Options 17. Code Default parameter options and definitionsTo note Parameter ASSIGN=X5A,X40,X40 ’40’ CODE2 Code DEFAULT=EBCDICDefault Code Spacecode parameter point to note Dbcode command Options 20. Dbcode Assign parameter options and definitions Dbcode command parameters19. Summary of Dbcode command parameters Dbcode Assign Iden command Dbcode DefaultDbcode command point to note Options 23. Iden Djpcc options and definitions Default DefaultIden Djpcc Options 25. Iden Oprinfo options and definitions Iden OffsetOptions 24. Iden Offset parameter option and definition Iden Oprinfo String constant Iden PrefixOptions 26. Iden Prefix parameter options and definitions Options 27. Iden Skip parameter options and definitions 28. Summary of Kcode command parameters Iden command exampleKcode command Kcode command parameters Options 29. Kcode Assign parameter options and definitions Kcode DefaultOptions 30. Kcode Default parameter options and definitions Kcode Assign 31. Summary of PCC command parameters Kcode command point to notePCC command PCC command parameters PCC Assign PCC AdvtapeOptions 32. PCC Advtape parameter options and definitions Field Syntax for ccln definitionOptions 33. PCC Assign parameter options and definitions Ccln Carriage control line number ASSIGN=X’60’, SP1, ASSIGN=X’61’, SP2, ASSIGN=X’62’, SP3 PCC DefaultOptions 34. PCC Default parameter options and definitions PCC Assign parameter points to note Options 35. PCC Initial parameter options and definitions Default TOFPCC Initial Options 36. PCC Mask parameter options and definitions Default X’FF’ PCC command points to notePCC command example PCC Mask Record Adjust Record commandRecord command parameters 37. Summary of Record command parameters From 1 to 4 bytes Options 38. Record Adjust parameter options and definitionsRecord Constant Parameter points OptionsDefinitions Options 41. Record Length parameter options Definitions Options 43. Record Lthfld parameter options and definitions Record LmultOptions 42. Record Lmult parameter options and definitions Record Lthfld Record Preamble Record OffsetOptions 44. Record Offset parameter options and definitions Record Postamble Constant and Structure parameters Default Record command Points to noteRecord Structure LTHFLD, OFFSET, FORMAT, and Preamble parameters Line Data parameter and Record Length parameter Using online JDEs in offline JDLsRecord command example Record format types Seffnt command Options 49. Seffnt Sefmap parameter options and definitions Seffnt command parameters48. Summary of Seffnt command parameters Seffnt Sefmap REP Replace Seffnt MAP Options 50. Seffnt MAP parameter options and definitions Seffnt command points to note Seffnt command examples JOB4 JOB Seffnt SEFMAP=L01BOB,P0812A Tcode command General rules for using the Tcode command 51. Specifying various types of character sets Tcode command parameters52. Summary of Tcode command parameters Tcode Tassign Tcode DefaultOptions 53. Tcode Default parameter options and definitions Default Tcode Default parameter points to note Options 54. Tcode Tassign parameter options and definitions Tcode Treset Tcode command examples Options 55. Tcode Treset parameter options and definitions 56. Summary of Volume command parameters T4 Tcode DEFAULT=EBCDICVolume command Volume command parameters Volume Lcode Volume KanjiVolume Kcode Volume Label Options 58. Volume Code parameter options and definitions Volume BmultOptions 57. Volume Bmult parameter options and definitions Volume Code Options 59. Volume Dbcode parameter options and definitions Default Volume Code parameter points to noteVolume Dbcode Options 61. Volume Emtype parameter options and definitions Volume DbcsOptions 60. Volume Dbcs parameter options and definitions Volume Emtype Volume Expage Volume EOVOptions 62. Volume EOV parameter options and definitions Options 64. Volume Host parameter options Definitions Options 63. Volume Expage parameter options and definitionsDefault YES Volume Host Double-byte printing Default Volume Host parameter points to noteRecord Length = Line Options 65. Volume Kanji parameter options and definitions Volume Kanji Syntax Volume KcodeOptions 66. Volume Kcode parameter options and definitions Options 67. Volume Label parameter options and definitions Volume Lpack Volume LcodeOptions 68. Volume Lcode parameter options and definitions Default Ebcdic Options 70. Maxlab parameter options and definitions Options 69. Volume Lpack parameter options and definitionsVolume Maxlab Volume Minlab Nccheck Options 71. Volume Minlab parameter options and definitionsVolume Optimize Options 74. Volume Oshdp parameter options Definitions Volume OschnOptions 73. Volume Oschn parameter options and definitions Volume Oshdp Volume Tcode Options 75. Volume Ostlp parameter options DefinitionsVolume Rmult Options 76. Volume Rmult parameter options and definitions Default None Options 77. Volume Tcode parameter options and definitionsVolume Unpack Options 78. Volume Unpack parameter options and definitions 80. Character Type code options Volume VcodeOptions 79. Volume Vcode parameter options and definitions 81. Unique character code types Default Volume Vcode examplesVolume command examples Volume HOST=IBMONL, CODE=EBCDIC Offline Types of commands for logical processing Using logical processing Coding a test expression Test expressions Criid Command-keywordT1 Table Tabid Table command Commands that define criteria and constantsLogical processing commands that have Test parameters Options Table Constant parameter options and definitions Table command parametersSummary of Table command parameters Table Constant Options Table Mask parameter options and definitions Table Mask CONSTANT=120 Table command points to noteTable command examples CONSTANT=$$ T2 Table Mask associations of character to type for the Table Command Character to type associations Criteria commandCriteria command modes Test = criid1, AND, criid2 Test = criid1, OR, criid2 Using the Criteria commandTest = criid String comparisons C1 Criteria Constant =offset,length,EQ,T1Rselect TEST=C1 Using logical processing Commands that specify string comparisons Masked comparisons using nondefault type assignments Criteria Change Criteria command parametersSummary of Criteria command parameters Not done and the test fails Options Criteria Change parameter options and definitions Criteria Constant CriteriaChange parameter syntax example Syntax Criteria Linenum Options Criteria Constant parameter options and definitionsConstant parameter syntax example Syntax Count Criteria ValueInitial line Tabid Table identifier Page Example Parameter syntax Banner command Logical processing command descriptions Banner Hcount Banner command parameters13. Summary of Banner command parameters Banner Hrptna Options 14. Banner Hcount parameter options and definitionsBanner Hjobno Options 15. Banner Hjobno parameter options and definitions Banner Test Options 16. Banner Hrptna parameter options and definitionsBanner Tcount Option 17. Banner Tcount parameter option and definition Data Default BannerOptions 18. Banner Test parameter options and definitions Options 19. Banner Type parameter options and definitions C1 Criteria Banner command points to noteBanner command examples Bselect and Bdelete Test parameter Bselect and Bdelete commandsC2 Criteria C1 Criteria CONSTANT=0,1,EQ,T1 Bselect TEST=C1 Bselect and Bdelete commands points to note21. Test parameter options and definitions C1 Criteria CONSTANT=4,4,EQ,T1 Bdelete TEST=C1 Sample Bselect and Bdelete command Usage Example Lmodify INK Lmodify commandLmodify command parameters 22. Summary of Lmodify command parameters Line Lmodify SelectLmodify Test Options 25. Lmodify Test parameter options and definitions Raux command Points to note Lmodify command Options 26. Raux Test parameter options and definitions Raux command points to noteRaux command example Raux Test parameter Rselect and Rdelete Test parameter Rdelete and Rselect commands Rdelete TEST=C1 Rdelete and Rselect commands point to noteRdelete command example T1 Table CONSTANT=EFGH C1 Criteria Rfeed Test parameter Rfeed command 28. Rfeed Test parameter options and definitions Rfeed command points to note Green Roffset commandCONSTANT= 15,3,EQ,T3 Rfeed Roffset Passes Roffset command parameters29. Summary of Roffset command parameters Default ALL Options 31. Roffset Test parameter options and definitions Roffset command points to noteRoffset Test Roffset TEST=C1, PASSES=ALL Roffset command exampleT1 Table CONSTANT=PAGE...1 C1 Criteria Rpage Side Rpage commandRpage command parameters 32. Summary of Rpage command parameters Options 33. Rpage Side parameter options and definitions Options 34. Rpage Test parameter options and definitions Options 35. Rpage When parameter options and definitionsDefault TOP Rpage Test Rpage command examples Rpage command points to note Effects of Rpage Side parameter Effects of Rpage When parameter Rsuspend and Rresume Begin Rresume and Rsuspend commandsRsuspend and Rresume command parameters 36. Summary of Rsuspend and Rresume command parameters Next Rresume and Rsuspend commands points to noteRsuspend and Rresume Test Current Interaction with Rstack Option Catal Assign SYSRLB,3340,TEMP Rsuspend and Rresume exampleBEGIN=CURRENT Rresume Rstack delimiter modes Rstack command Status display Delimiter on accounting Rstack Acctinfo Rstack command parameters39. Summary of Rstack command parameters Rstack Hrptna Rstack Delimiter Options 43. Rstack Print parameter options and definitions Default Rstack Print parameter points to noteOptions 42. Rstack Hrptna parameter options and definitions Rstack Print Points to note for online printing Rstack command points to noteRstack Test 44. Test parameter options and definitions HRPTNA=20,10 Rstack command exampleACCTINFO=14,19 Sample Rstack command usage illustration Summary of print format commands Print format command descriptions Abnormal Acctfeed Abnormal commandAbnormal command parameters Summary of Abnormal command parameters Abnormal Code Abnormal Error Abnormal Options Abnormal Error parameter options and definitionsError Abnormal Imismatch Default StopPage Abnormal Otext Default ANYAbnormal Isubstitute Options Abnormal Isubstitute parameter options Definitions Options Abnormal REP parameter options and definitions Default Abnormal Otext parameter exampleOptions Abnormal Otext parameter options and definitions Abnormal REP JDL Abnormal SecuritySecurity Acct Dept Acct commandAcct command parameters 11. Summary of Acct command parameter Options 13. Acct User parameter options and definitions Default BIN Acct command points to noteAcct command example Acct User L49 P10, C’ABCD’ CME commandCME12.CME L47 14. Summary of the CME command parameters CME command parameters Option 16. CME Font parameter option and definition CME ConstantOptions 15. CME Constant parameter options and definitions CME Font Option 17. CME INK parameter option and definition Parameter pointsXYZ CME CME INK Line =2,3, POS=15 CME LineOptions 18. CME Line parameter options and definitions CME1 CME Options 19. CME Position parameter option and definition Default CME command points to noteCME Position Copy sensitive CMEs Position CME command examples IDR File will be Used During Printing IDR command Options 21. IDR Icatalog parameter options and definitions IDR command parameters20. Summary of IDR command parameters IDR Icatalog Dfidr IDR Ilist = ‘BLACK‘ Default IDR Ilist parameter points to noteIDR Ilist Options 22. IDR Ilist parameter options and definitions IDR Palette Line commandLine command parameters 24. Summary of Line command parameters Line Baseline Line Blanktype Default NospaceOptions 25. Line Baseline parameter options and definitions Line FCB Default ProcessLine Data 27. Line Data parameter options and definitions If offline, no terminating byte exists Line FdataOptions 29. Line Fdata parameter options and definitions If online, a single terminating byte exists Specifies that there is no font index Line Fontindex Line Gdata Line Fontindex parameter points to note Syntax Options 32. Line Inkindex parameter options and definitions Default offsetOptions 31. Line Gdata parameter options and definitions Line Inkindex Line LPI ParameterDATA=1,132, FONTINDEX=133 INKINDEX=143 34. Line Margin parameter options and definitions Default Line LPI parameter points to note Syntax OptionsLine LPI = Linespacing Line Margin Options 35. Line Overprint parameter options and definitions Default Line Overprint parameter points to note Line PCC Line Overprint parameter exampleDATA=1,132, PCCTYPE=ANSI PCC=0,NOTRAN Options 37. Line Pcctype parameter options and definitions Line Pcctype Control of Print and Space Line VFU38. Line VFU parameter options and definitions Line command points to note VFU=V1, FONTINDEX=1 Line command examplesDATA=1,132, PCC=0,NOTRAN Example 3 Line PCCTYPE=NONE, DATA=1,57, VFU=V1 Message command Options 40. Message Itext parameter options and definitions Message command parameters39. Summary of Message command parameters Message Itext END Message OtextOptions 41. Message Otext parameter options and definitions Message command example Message command points to note 42. Summary of Output command parameters Output commandOutput command parameters Output Image Output IdfaultOutput Graphics Output IDR Nuvera MX systems Output Bform43. Bform parameter options and definitions Inkref Ink reference Default Long43. Bform parameter options and definitions Output Binding Specifying print format parameters Specifying print format parameters Output Copies Output CollateOutput Collate parameter points to note Output Cycleforms Output CoverOptions 47. Output Cover parameter options and definitions Formid CycleformsOutput CYCLEFORMS=form1, form2 Parameter Example Nofix Output DensityOutput Destination FIX Output Faceup Default BINOutput Duplex Options 51. Output Duplex parameter options and definitions ‘stockname’ Options 52. Output Faceup parameter options DefinitionsOutput Feed Options 53. Output Feed parameter options and definitions Options 54. Output Format parameter options and definitions Default FMT1Output Format Options 55. Output Forms parameter options and definitions Output Forms Forms FORM4, Copies Cycleforms and Forms parameters Both may beOutput Forms FORM12,1,2 Move Default Output Graphics parameter points to noteOutput Idfault Output Graphics parameter examples Output IDR Output IDR=IDR1 parameter Output Idfault Output IDFAULT=’RED’ parameterOutput IDR Options 58. Output IDR parameter options and definitions Options 59. Output Image parameter options and definitions Output Image Options 60. Output Invert parameter options Definitions Output GRAPHIC=BATCH, IMAGE=1 IN,2 CMOutput Invert Black Default Output Iresult parameter points to note60. Output Invert parameter options Definitions Output Iresult Logo Output LogoOptions 62. Output Logo parameter options and definitions Xdots 600 dpi dots Specifies that data are processed without modification Output ModifyOptions 63. Output Modify parameter options and definitions Options 64. Output NTO1 parameter options and definitions Output NTO1 Number Options 65. Output Number parameter options and definitions Output Number 65. Output Number parameter options and definitions Options 66. Output Offset parameter options Definitions Number character string is placed on the page atOutput Offset Output Offset = ALL First None 67. Output Ostk parameter options and definitions Where ostkspec isOutput Ostk 67. Output Ostk parameter options and definitions DefaultsPage Output FEED=regular stock, DUPLEX=NO or DUPLEX=YES Page Uslegal Default Output Papersize parameter points to noteWhat to do Output Papersize Output Purge Output Papersize parameter example Output SF1FUNCTION Options 69. Output Purge parameter options and definitions Output Shift Output SF2FUNCTION Options 72. Output Shift parameter options and definitions Best Default Output Sizing parameter points to noteOptions 73. Output Sizing parameter options and definitions Semiauto Options 74. Output Staple parameter options and definitions Output Staple Options 75. Output Stocks parameter options and definitions Default No defaultOutput Stocks Options 76. Output Sysppr parameter options Definitions Output Sysppr Sysppr and the Stockset Syspage parameter Options 77. Output Tmode parameter options and definitions Default Output Tmode parameter points to noteInches is the default widthunit Output Tmode Pitch Dots Xdots PPM Pitch modes and throughput performance The printingPage Page Output Units Output TransDP 100/115/135/155/180 EPS only Transparencies cannot Size Options 80. Output Units parameter options and definitionsOutput Xshift Options 81. Output Xshift parameter options and definitions Output command examples Output command point to note Illustration of ways to use Output Offset Parameter Example Standard PDEs 82. Standard print formats PDEs PDE Begin PDE command parameters83. Summary of PDE command parameters PDE Begin Options 84. PDE Begin parameter options and definitions Bform Copies Duplex JDE JDL Otext Rtext Options 85. PDE Fonts parameter options and definitions PDE Fonts Landscape PDE PmodeOptions 86. PDE Pmode parameter options and definitions PDE2 PDE PMODE=PORTRAIT, BEGIN=1.3,.37 PDE command points to notePDE command examples PDE1 PDE PMODE=LANDSCAPE, BEGIN=.861,.7 87. Summary of Route command parameters Route commandRoute command parameters Formid Form identifier Route RformOptions 88. Route Rform parameter options and definitions Route Rtext Specifies that the text applies to all copies CommandOptions 89. Route Rtext parameter options and definitions Refer to the fontindex option in this table ROUTEF1 Route Route RTEXT=‘USER1,1,33,64 RTEXT=USER2,2,33,64 Route command exampleStockset command RTEXT=ROUTE1 Example of use of Assign = ’F1302’, COVER,’F1415’, Body Stockset command parameters90. Summary of Stockset command parameters Stockset Assign Stockset Syspage Stockset Inifeed Example of mismatch handling StocksetPaper size mismatch on system pages Pages generated Syspage Syspage = Coverend Stockset command exampleBills Stockset Assign = F1302, Cover F9999, Discon VFU Assign VFU commandVFU command parameters 94. Summary of VFU command parameters VFU TOF Options 95. VFU Assign parameter options and definitionsOptions 96. VFU BOF parameter options and definitions 97. VFU TOF parameter options and definitions VFU command points to note ASSIGN=12,55, TOF=5, BOF=55 VFU command exampleV1 VFU ASSIGN=1,5Page Iden PREFIX=RTEST, SKIP=9, OFFSET=3 OPRINFO=YES Using the Iden command to enable DJDEs Iden PREFIX=EDJDE, SKIP=7, OFFSET=2 OPRINFO=YES Specifying Djde records Application of DJDEs Iden PREFIX=MTEST, SKIP=7, OFFSET=1 OPRINFO=YES Mtest C MULTI-RECORD Djde ExampleMtest COPIES=20,COLLATE=YES, ASSIGN=1,5, ASSIGN=5,32 Mtest FONTS=P0612A,P0812A Mtest ASSIGN=12,63, TOF=5, BOF=66 Messages on Missing END command or page boundary. The followingMissing END Command or Missing page Boundary Djde operator information pages Parameters that are not changeable by a JDE Djde Restrictions on job parameter modificationParameters that cannot be changed through a JDE Djde Rdelete Record Length Rfeed Roffset Parameters that are changeable by a JDE DjdeDjde Abnormal Acct Solution Considerations and cautions for using DJDEs JDE JDL DUPLEX=NO Feed Carriage control parameter Processing with Djde Types of DJDEs Accounting log. You can print out the values Oriented DJDEs Margin ItextJDE MAP LPI Record oriented DJDEsAssign File Alter Djde Djde descriptionsRecord oriented DJDEs for graphics UN user defined units Options Alter Djde options and definitionsAlter Djde point to note Examples of Alter Djde Batch Djde Assign DjdeAssign Djde options and definitions Assign Djde points to note Start Options Batch Djde options and definitionsBatch Djde points to note Begin Djde Bform Djde 10. Begin Djde options and definitionsBegin Djde points to note References Options 11. Bform Djde options and definitionsBform Djde points to note Init Initial copy Syntax C text BOF DjdeBOF Djde points to note Text Djde Text Djde points to note Cancel DjdeOptions 14. Cancel Djde options and definitions Options 13. C text Djde options and definitions Copies Djde Collate DjdeOptions 15. Collate Djde options and definitions Collate Djde point to note Data Djde point to note Copies Djde points to noteData Djde 17. Data Djde options and definitions Dept Djde points to note Dept DjdeSyntax Dept = sc Options 18. Dept Djde options and definitions Options 20. Duplex Djde options and definitions Options 19. Destination Djde options and definitionsDestination Djde points to note Duplex Djde Syntax EOF EOF Djde point to note END DjdeSyntax END END Djde points to note EOF Djde Fdata Djde Feed DjdeOptions 21. Feed Djde options and definitions 23. File Djde options and definitions Options 22. Gdata Djde options and definitionsFile Djde FILE=,,C or FILE=END,,C 23. File Djde options and definitionsFile Djde points to note FILE= Card image file processing LPS labeled file processing Page Fontindex Djde Fontindex Djde points to note 24. Fontindex Djde options and definitions 25. Fonts Djde options and definitions Fonts Djde Fonts Djde points to note 25. Fonts Djde options and definitions Format Djde points to note Format Djde26. Format Djde options and definitions Forms Djde point to note Forms Djde27. Forms Djde options and definitions Graphic Djde Gdata DjdeOptions 28. Gdata Djde options and definitions 29. Graphic Djde options and definitions Graphic Djde points to note Icatalog Djde example Idfault DjdeIcatalog Djde Options 30. Icatalog Djde options and definitions Ilist Djde IDR Djde32. IDR Djde options and definitions 34. Image Djde options and definitions Options 33. Ilist Djde options and definitionsIlist Djde example Image Djde Inkindex Djde 34. Image Djde options and definitions Invert Djde 35. Inkindex Djde options and definitions Options 37. Iresult Djde options and definitions Systems, the default is BlackOptions 36. Invert Djde options and definitions Iresult Djde Syntax JDE = JDEid Itext DjdeOptions 38. Itext Djde options and definitions Itext Djde points to note JDL Djde 39. JDE Djde options and definitionsJDE Djde points to note 41. Logo Djde options and definitions JDL Djde points to noteLogo Djde 41. Logo Djde options and definitions 42. LPI Djde options and definitions Logo Djde points to noteLPI Djde Options 43. MAP Djde options and definitions 42. LPI Djde options and definitionsLPI Djde point to note MAP Djde Type Options 44. Margin Djde options and definitionsMargin Djde points to note Modify Djde Number Djde Modify Djde points to note Number Djde point to note 46. Number Djde options and definitions Using Dynamic Job Descriptor Entries DJDEs Options 47. Otext Djde options and definitions Number Djde exampleNUMBER=1,1,40,1, END Otext Djde Overprint lines is always printed on the accounting Otext Djde point to noteOverprint Djde 48. Overprint Djde options and definitions Options 49. Palette Djde options and definitions Overprint Djde points to notePalette Djde Pmode Djde point to note Palette Djde examplePmode Djde Options 50. Pmode Djde options and definitions Specifies that no form will be printed with Rtext pages 51. Rform Djde options and definitionsRform Djde points to note Rtext Djde Specifies that no text is to be printed on a separate 52. Rtext Djde options and definitionsRtext Djde example RTEXT=’TEST’,ALL,15,5,2 Sefmap Djde Save Djde53. Save Djde options and definitions Save Djde point to note Sefmap Djde examples Options 54. Sefmap Djde options and definitionsSefmap Djde points to note Options 55. SF1FUNCTION Djde options and definitions SEFMAP=font1,font7, font5,font6,REPFont1,font7, font5,font6 SF1FUNCTION Djde Shift Djde SF2FUNCTION DjdeOptions 56. SF2FUNCTION Djde options and definitions Side Djde 57. Shift Djde options and definitionsShift Djde points to note Offsetopt Options 58. Side Djde options and definitionsSide Djde points to note Tmode Djde Stocks DjdeOptions 59. Stocks Djde options Definitions Stocks Djde point to note 61. TOF Djde options and definitions 60. Tmode Djde options and definitionsTOF Djde Syntax TOF = value Options Trans Djde points to note Trans DjdeOptions 62. Trans Djde options and definitions Report XMP DjdeOptions 63. XMP Djde options and definitions 64. Xshift Djde options and definitions Xshift Djde Djde definitions for graphics Output command parameters and functions for graphics Input for graphics Graphic processing modes Error handling for graphics Formats for graphic data Page Impact of graphics on system performance Graphics features restrictionsRandom Move mode Page Page Contents of command table columns Table A-1. Symbols used in command syntax Table A-2. PDL commands and DJDEs Summary table of PDL commands and DJDEs ‘inkref’’ Name Text ‘inkref’ Filename FreeFlow Print Server Lcds Systems AcIDRJdename All Jdlname All AcJOB Blanktype Nospace Fdata DefaultGdata Default Line Baseline Largest Otext None Ucsb ProcessVFU None Message Itext None Cover None Density DefaultBinding Long Collate YES Mod & pos =1 Width unit=IN 18 IN, .66 All No default for All except 9790 Stockdef 8790 LPSAcPCC All AcPDE First ‘stockname’ All Record AcTCODEAll AcVFU Ostlp Volume Optimize NoneOschn OshdpPage Table B-1. Symbols used in command syntax PDL command quick reference Testexp PDL command Quick Reference tableTable B-2. PDL command quick reference table Acct User = BIN Tray Both None Alter Djde Block Zero = YES no Bselect Bdelete JDE = JDEname Only OnlyFile = filename , filetype , f , s , n Only Iden Offset = value Wait None Line FCB = Ignore ProcessLine Ucsb = Ignore Process Lmodify Lmodify = Test Message Inkindex1 , inkindex2 Inkref1 , inkref2Output Feed = stockreference ‘stockname’ Main AUX Output Papersize = A3 A4 B4 B5 Uslegal Output Purge = YES no Output Resolution = 300Output XMP = Default Report Output Offset = ALL First None Raux Test = testexp Rfeed Test = testexp, stockdef No default for StockdefAcPDE AcPDE Begin = vpos, hpos 18 IN, .66 L0112B Rsuspend Rsuspend Begin = Current Next AcTABLE Mask = ignore chart ,charspeci1 , charspeci2Rstack Delimiter = YES no Rstack Print = BIN Both Tray None Volume Vcode = translation type, keyword Volume Tcode = tcodetype tcodename Character code assignments Table C-2. Honeywell/Bull 200 and 2000 BCD code set IBM BCD code setHoneywell/Bull 200 and 2000 BCD code set Table C-1. IBM BCD code set Table C-4. Fieldata translation Honeywell/Bull 6000 BCD code setFieldata translation Table C-3. Honeywell/Bull 6000 BCD code set Table C-5. Univac Ascii character set Univac Ascii character set Table C-6. Standard Ascii character set Standard Ascii character set Table C-7. Standard Ebcdic character set Standard Ebcdic character set Ebcdic most significant digit Page Figure D-1. Input unpacking examples Input unpacking examples Table D-1. Valid host computer and label specifications Valid host computer and label specifications Xerox NEC NCR OldumpOswtr Octdump RSX11 Stdout Table D-2. JDL source files on software CD Host system JDLs on system software CD LPS tape label format Figure D-2. LPS tape format diagram Table D-4. RAD-50 character set Table D-3. Content of tape records Offline specifications Using Lcds Print Description Language Glossary Page Ascii Page Page Page Program Ipfonts IOMIOT IPDPage Page Page Page Page Page Page Page Index INDEX-2 Duplex Djde Default ParameterDestination Djde Copies Djde FCB IBM JSL INDEX-7 PPI PCC Sefmap Djde SEF INDEX-10 INDEX-11 Index INDEX-12