Cir | Cisco Systems MGX 8230 specs

Chapter 6 Card and Service Configuration

Configuring Frame Relay Service

cnfchanstdabr <Port.DLCI/CHAN_NUM> <mcr> <pcr> <icr> <rif> <rdf> <nrm> <trm> <tbe> <frtt> <adtf> <cdf>

Please note the following:

•Standard ABR is a connection-level feature that requires the Rate Control Feature to be enabled on the card.

•Standard ABR does not support Explicit Rate (ER) marking of RM cells.

•cnfconabrrates can be used to modify the rates:

Usage: cnfconabrrates <Port.Vpi.Vci/Chan_Num> <mcr> <pcr> <icr>

•cnfconabrparams can be used to modify the parameters.

Usage: cnfconabrparams <Port.Vpi.Vci/Chan_num> <ABRType> <rif> <rdf> <nrm> <trm> <tbe> <rtt> <adtf>

Variable	Description	Value range	Default value

mcr	Minimum Rate	Valid value range from 10 to 10,000 (includes	Derived from
		RM cell and Data cell bandwidth).	CIR

pcr	Peak Rate	Valid value range from 10 to 10,000 (includes	Derived from
		RM cell and Data cell bandwidth).	CIR

icr	Initial Cell	Valid value range from 10 to 10,000 (includes	Derived from
	Rate	RM cell and Data cell bandwidth).	CIR

rif	Rate Increase	Valid value range from 1 to 32768 (power of 2).	64
	Factor

rdf	Rate Decrease	Valid value range from 1 to 32768 (power of 2).	16
	Factor

nrm	Inrate Cell	Valid value range from 2 to 256 (power of 2).	64
	Count

trm	Time limit for	Valid value range from 3 to 255 msec.	255 msec
	Frm

tbe	Transient Buf	Valid value range from 0 to 16777215 cells.	16777215 cells
	Exposure

frtt	Fixed Round	Valid value range from 0 to 16700 msec.	0 msec
	Trip Time

adtf	ACR Decrease	Valid value range from 10 to 10230 msec.	500msec
	Time Factor

cdf	Cutoff	Valid value range from 0 to 64 (power of 2).	16
	Decrease
	Factor

Step 6 Use cnfchanfst to configure the parameters for ForeSight ABR, if necessary.

cnfchanfst <Port.DLCI/CHAN_NUM> <ForeSight enable> <mir> <pir> <uir>

		Cisco MGX 8230 Edge Concentrator Installation and Configuration

	Release 1.1.31, Part Number 78-11215-03 Rev. B0, May 2001			6-35
	Release 1.1.31, Part Number 78-11215-03 Rev. B0, May 2001			6-35

Image 203

Cisco Systems MGX 8230 manual Cir

Contents

Corporate Headquarters Copyright 2001, Cisco Systems, Inc All rights reserved Mailing Information General InformationDocument Information Business Reply Mail N T E N T S Cell Bus Module Requirements with Bulk Distribution and Redundancy Wiring a Mixed Ground System with Redundant Supplies Other Ports Card and Service Configuration Configuring Logical Interfaces for the Feeder Features FRSM-2CT3 Framer Technical Specifications ATM UNI Xiv G U R E S Figure B-1 B L E S Table A-1 Table A-33 Release 1.1.31, Part Number 78-11215-03 Rev. B0, May This document is organized into the following chapters AudienceOrganization Documentation Description Related Documentation Cisco WAN Manager, Release 10, Related Documentation Xxiv Conventions Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROM Cisco.com To access Cisco.com, go to the following websiteObtaining Technical Assistance Documentation Feedback Contacting TAC by Telephone Contacting TAC by Using the Cisco TAC WebsiteTechnical Assistance Center Xxviii A P T E R Introducing the MGX MGX 8230 with Door Attached MGX 8230 System Overview Universal Edge Architecture Applications of the MGX Standards-Based Conversion to ATM MGX 8230 Enclosure and PowerSlot Numbering and Placement PXM Single Height and Double Height Slots Optional AC Power Supply MGX 8230 Power System AC Power Supply Module, Rear View DC-Powered MGX Cooling System MGX 8230 DC Power Entry Module MGX 8230 Architecture MGX 8230 Fan Tray Assembly PXM-UI Cell Bus Cell Bus Distribution MGX 8230 Management Summary of MGX 8230 Cards and Modules Introduction to Core Card Sets and Service ModulesProcessor Switching Module PXM1 MGX-BNC-2E3 User Interface Back CardsMGX-BNC-2T3 ATM UNI Service Modules Ausm Service Resource Module SRMFrame Relay Service Modules Frsm Route Processor Module RPM Circuit Emulation Service Modules CesmVoice Service Modules Vism 1N Redundancy Redundancy for Service ModulesRedundancy Hot Standby Introducing the MGX Summary of MGX 8230 Cards and Modules Release 1.1.31, Part Number 78-11215-03 Rev. B0, May Processor Switching Module Module and Service Descriptions PXM1 Illustration and LED Description PXM1 Features PXM1-UI standard PXM1 User Interface Back Cards Stratum 4 clocking Maintenance, Control and LAN portsMaking External Clock Connections PXM-UI-S3 optional PXM1 User Interface Back Cards PXM1 Back Cards User Interface Back Card PXM-UI-S3 Stratum 3 Clocking Alarm Output Connection OC-12 Long-Reach Back Card SMFLR-1-622/B SMFLR-1-622 Back Card OC-12 Intermediate-Reach Back Card SMFIR-1-622/B SMFIR-1-622 Back Card OC-3 Four-Port Back Card SMF-155/B SMF-155 Back Card Two-port T3 Back Card BNC-2T3 BNC-2T3 Back Card Two-port E3 Back Card BNC-2E3 BNC-2E3 Back Card Bulk Distribution Mode Service Resource ModuleBit Error Rate Testing 1N Service Module Redundancy Type of LED Color Meaning Installation Requirements for the MGX-SRM-3T3/CSRM Illustration and LED Indicators Module Requirements with Bulk Distribution and Redundancy MGX-SRM-3T3/C Card Set Inverse Multiplexing ATM UNI Service Module AusmAusm Features Quality of Service QoS Management E1 Cards Physical Layer FeaturesAll Cards T1 Cards 10 AUSM/B-8T1 or AUSM/B-8E1 Front Card Ausm Front Card Illustration and LED Description Type of LED Color Description Back Cards for the AUSM/B 11 RJ-48 and SMB Back Cards for the MGX-AUSM-8T1E1/B Frame Relay features Frame Relay Service ModulesFeatures Common to All FRSMs Data-Link Layer features Frame Forwarding Features ATM Funi features Connection Types on the Frsm Redundancy for Frame Service Modules Congestion Indication Frame Relay-to-ATM Network InterworkingCongestion Indication for NIW Connections Efci is always set to Frame Relay-to-ATM Service InterworkingPVC Status Management Cell Loss Priority Translation and Transparent Modes Command and Response MappingFrame Forwarding ATM Frame-to-User Network Interface There are three types of FRSMs Types of Frame Service ModulesFrsm for T1 features FRSMs for T1 and E1 Lines Stby LED Frsm for E1 featuresLED Indicators ACT LED Card Illustrations 14 MGX-FRSM-8T1 15 RJ-48 and SMB Back Cards for the MGX-FRSM-8T1/E1 FRSMs for T3 and E3 lines Features Illustrations FRSM-2T3E3 LED Indicators6and -7describe the FRSM-2T3E3 LED faceplate indicators Card Combinations 16 MGX-FRSM-2CT3 17 MGX-FRSM-2T3E3 18 BNC-2T3 19 BNC-2E3 For the MGX-FRSM-HS2 front card, see -20 on FRSMs for Serial ConnectionsFRSM-HS1/B X.21 and V.35 Interfaces FRSM-HS2 Hssi Interfaces DCE Mode Type of Cable Clock Source Mode of Far EndMGX-FRSM-HS1/B Cabling Cable Type DTE-DCE Type of Cable Far End Connector Part NumberDtest DTE 20 MGX-FRSM-HS2 21 MGX-FRSM-HS1/B Front Card Faceplate 22 SCSI2-2HSSI 23 12IN1 S4 Back Card Faceplate Cesm for T1 and E1 lines Circuit Emulation Service ModulesCesm T1 and E1 Features AX-SMB-8E1-LM LED Indicators for the Eight-Port Cesm1N Redundancy for the Cesm T1/E1 Cesm T1/E1 Illustrations Fail LED 24 Front Cards for the Eight-Port Cesm 25 RJ-48 and SMB Back Cards for the MGX-CESM-8T1E1 T3 Interfaces CESM-T3/E3 FeaturesCesm for T3 and E3 lines E3 Interfaces MGX-CESM-T3/E3 front card is shown in -26 on Cesm T3/E3 Illustrations 27 BNC-2T3 Back Card for the CESM-T3/E3 28 BNC-2E3 Back Card for the CESM-T3/E3 Vism Documentation Voice Service The VismSummary of Features Supported with Vism T3 Interfaces via SRM Bulk Distribution Card Combinations Vism Redundancy Vism Card Illustrations and LED Description 29 Vism Front Cards 30 Vism Back Cards RPM Documentation Route Processor Module RPM Release 1.1.31, Part Number 78-11215-03 Rev. B0, May Environment Operating environment should be as follows Parts ChecklistSite Preparation Site Preparation Safety Recommendations Regulatory Compliance and Safety InformationMaintaining Safety with Electricity Site Preparation Maintaining Safety with Electricity Product Disposal Warning Site Preparation Maintaining Safety with Electricity Lightning Activity Warning Jewelry Removal Warning Power Supply Warning Power Supply Disconnection Warning Power Disconnection Warning Grounded Equipment Warning Installation Warning Class 1 Laser Product Warning Laser Beam Warning Seismic Anchoring for a Cisco Rack Seismic Considerations Stability Plate Dimensions Installing a Cisco Cabinet Over the Stability Plate Electrical Power for AC-Powered Nodes Power and GroundingAC Power Circuit Breakers DC Power Circuit Breakers Bonding and Grounding Wiring a Mixed Ground System with Redundant Supplies Connection Description DC Current Distance in Feet Gauge Ohms per 1000 Feet Using the Electrostatic Wrist StrapCo-Locating Cisco Units in the Same Rack Making the Frame Bonding Ground Connection Making Cisco Cabinet Ground Connections Frame Bonding Connection in Cisco-Supplied Rack Release 1.1.31, Part Number 78-11215-03 Rev. B0, May Mechanical Lift Guidelines Chapter Summary Rack Mounting an MGX Installing a Stand-Alone MGXIf the switch is a stand-alone unit, proceed directly to Rack Positioning Prepare for Rack InstallationBracket Placement Mounting Kits 17273 Rack Mounting Procedures for 23-Inch Racks Mechanical Lift Install the MGX 8230 Using a Mechanical Lift RecommendedRack Mounting Procedures for 19-Inch Racks Mechanical Lift To remove a front card Install the MGX 8230 Without a Mechanical Lift OptionalPrepare for Installation Remove the Front Cards Follow these steps to mount an MGX 8230 in a 19-inch rack Remove the Back CardsRack Mount the MGX 8230 chassis Inch rack mounting Front View of MGX 8230 with 23-Inch Mid-Mounting Brackets Re-install the back cards Re-install the front cards Rear View of MGX 8230 with Two DC PEMs Connecting Power for DC Systems Rear View of MGX 8230 with 1 DC PEM Polarities at MGX 8230 PEM Pluggable Terminal Block DC PEM 11 Optional 1200 Watt AC Power Supply Module, Rear View Connecting Power for AC Systems Making the Connections to the AC Power Supply Modules 23825 13 Rear View of MGX 8230 with One AC Power Supply Module Install the Cable Manager 14 Cable Management System on Rack-Mount MGX Power up the MGX Configuring the MGX 8230 as an BPX Feeder Release 1.1.31, Part Number 78-11215-03 Rev. B0, May Word bay refers to the upper or lower half of the enclosure Summary of Shelf-Level Tasks Ethernet Port User Interface Access PortsEthernet port Maintenance port Control Port Other Ports Maintenance PortMGX 8230 MGX to BPX Feeder Initial MGX 8230 Bring-Up Inet on ethernet e 188.29.37.14ffffff00 Bringing Up an MGX 8230 PXM With No Run-time Firmware Bin Enter the following Configuring Node-Level ParametersResource Partitioning Nodename.1.slot.cardtype.a Procedure Cnfpasswd username Adduser userId accessLevel Then Downloading Firmware to a Service Module$tftp IP address Configuring the OC-3 Uplink MGX 8230 CLI Configuration of a Feeder Addport portnum linenum pctbw minvpi maxvpi Commands are cnfport, dspports, and delport Cnfifastrk slot.port trunk Establishing the BPX 8600-to-BPX 8600 Series Segment Selecting an MGX CiscoView Configuration of a Feeder Activating a Physical Line for the Uplink Specifying the Feeder Application Configuring Logical Interfaces for the Feeder Partitioning Resources on the Broadband Interface Configuring the Line as a Feeder Trunk Modifying the Resource Partitioning Connections on a Feeder Rules for Adding a DAX Connection Sequence of Configuration TasksRules for Adding Connections Rules for Adding Three-Segment Connections Frame Relay Connection Through an MGX 8230/BPX Network Clock Sources Configuring Synchronization for the Shelf Clock types are primary, secondary, and tertiary Clock Source ConfigurationConfiguration Example Clock Source Types Cnfcdrscprtn numberPARconns numberPNNIconns numberTAGconns Configuring PXM1 Card-Level Parameters, Lines, and PortsFor an internal clock source Cnfextclk ClockType Impedance Cnfatmln linenum type APS Requirements Automatic Protection Switching on the PXM1APS Configuration Adding Connections on a PXM1 in a Stand-Alone Node Cnfcon connID routepriority maxcost restricttrunktype CAC ATM Forum TM spec PCR Flow PolType =5 VBR.3PolType =3 PolType =4 Summary of Ausm Features ATM Universal Service Module Ausm Cnfportq portnum qnum qalgo qdepth clphigh clplow efcithres Configure the Card, Lines, and Ports =CBR =VBR =ABR =UBR Addimagrp groupnum porttype listoflinks minNumLink Configure Inverse MultiplexingAdding and Configuring Connections on the AUSM/B Port number is in the range Release 1.1.31, Part Number 78-11215-03 Rev. B0, May Cnfchanfst port.vpi.vci enable fgcraenable ibs pcr mcr icr Release 1.1.31, Part Number 78-11215-03 Rev. B0, May If necessary, change the queue depths by using cnfchanq Variable Description Value range Default value BPX 8600-to-BPX 8600 Segment Frame Service Module Features Summary of Frame Service Module Features MGX-FRSM-2T3E3 Features MGX-FRSM-2CT3 Features MGX-FRSM-HS1/B Features MGX-FRSM-HS2 Features Eight-Port Frsm Features Configuring Frame Relay Service Correspond to Line Rates in Kbps Configuring the Frsm Cards, Lines, and PortsCnfln linenum linetype linerate Addport portnum linenum ds0speed beginslot numslot porttype Addport portnum linenum porttype Cnfport portnum lmisig asyn elmi T391 T392 N391 N392 N393 Addport portnum porttype Adding a Frame Relay Connection Release 1.1.31, Part Number 78-11215-03 Rev. B0, May Service Type Default EgressQueue PXM1 Service Type Cnfchanmap channum chanType FECN/EFCI DE to CLP CLP to DE CIR Establishing the BPX 8600-to-BPX 8600 Series Segment Test Commands for the FRSMs Bit Error Rate Testing on an Unchannelized T3 or E3 Frsm Support for Alarm Reporting Cell Delay Treatment Circuit Emulation Service Module for T3 and E3Features AIS-OAM Configuring Service on a T3 or E3 CesmError and Alarm Response Alarm Down Error Type Stream Up Stream Comments Adding and Modifying Connections Configuring the Card, Lines, and Ports Cnfcon portnum Cdvt CellLossIntegPeriod bufsize Addcon portnum mastership remoteConnId Bit Error Rate Testing on a T3 or E3 Cesm Eight-Port Circuit Emulation Service Modules Unstructured Data Transfer Structured Data Transfer Redundancy Support for the Eight-Port Cesm Cell Delay TreatmentError and Alarm Response AIS over the T1 link or alternating 1s Configuring Service on an Eight-Port CesmCnfln linenum linecode linelen clksrc E1-signalling Receive LOF Receive AIS Blue AIS AIS link Addport portnum linenum beginslot numslot porttype Configuring Bulk Distribution and Redundancy Execute addred Release 1.1.31, Part Number 78-11215-03 Rev. B0, May Configuring Card and Line Parameters NumberOfT1s Number of T1s, in the range Bulk Distribution for T1 ServiceT1Slot T1 slot number, in the range Redundancy Support by the MGX-SRM-3T3/C Configuring Redundancy Through the Redundancy Bus RedType Is a number that specifies the type of redundancy Configuring Redundancy Through the Distribution Bus Bit Error Rate Testing Through an MGX-SRM-3T3 Port Any Remote loopback Line Metallic or remote Test Medium Medium Type Device to Loop Bert PatternTest Medium Medium Type Loopback Port Any None All patterns Line Metallic Line Remote or metallic Pattern Test OptionsLine Far end, remote, or Metallic Line None All patterns Loopback Test Options Online Diagnostics testAutomatic Switchover Alarms Oldiags-help or oldiags help Commands to Operate the Online DiagnosticsOldiags debuglevel switchenable Log Files Oldsplog logname Configure Loopback on the Entire DS3 LineDS3 Loopback Test Loopback Tests To verify that DS3 interface can be put into loopback Configure Loopback on All DS1s in a DS3 LineReceive a Loopback Request Configure DS3 to Send Line Loopback Configure Transmit Feac CodeConfigure DS3 for Sending Looped or Normal Data Dspln should show LineXmtFEACCode as SendResetCode Configure Receive Validation Feac CodeConfigure DS3 for Sending Loopback Deactivation Request Configuring Feac Validation Criteria to be FEACCodes4Of5 Negative Tests Configure Feac Validation Criteria to be FEACCodes8Of10Disable Feac Codes Configure DS3 Loopback Codes from the Standby PXM1 Card Card and Service Configuration DS3 Loopback Test Frsm HS1/B Specifications Technical Specifications Value Category Description MGX 8230 Processor Switching Module Specifications LED Category Description IEC AUSM/B-8T1E1 Interface CharacteristicsESD CBR, VBR, VBR+ LOS, OOF, AIS, RAILCV, LES, LSES, CV, ES, MGX 8230, SEFS, AISS, UAS LM-SMB-8E1 Other Counters Counter Type DescriptionATMizer Channel Counters B3ZS FRSM-2CT3 SpecificationsFeature Significance or Value Interface Standard Interoperability Implementation Agreement v FRSM-2T3E3 SpecificationsFRSM-2CT3 Line Alarms FRSM-2CT3 Framer T3 Framer Level T3 line characteristics appear in Table A-13FRSM-2T3E3 T3 Line FRSM-2T3E3 E3 Line FRSM-HS2 SpecificationsFRSM-2T3E3 Line Alarms Statistics and Counter Specifications SCSI-2 Number of Hssi Lines Two Connector Type Counter Service Statistic ATM Cell Statistic ECN current queue depth, per channel Diagnostic StatisticTroubleshooting Statistic Interfaces FRSM-8T1 Specification FR/ATM PVC Interworking Implementation Agreement FRF.5 Table A-26 List of Counters FRSM-8E1 Specification Table A-28 Frame Relay Service With E1 Lines FR/ATM PVC Interworking Implementation Agreement FERF.5 Diagnostics per port Last unknown Dlci that arrivedTransmit frames s Changes Table A-30 List of Counters B8ZS Circuit Emulation Service Module for T1 Operation Category Circuit Emulation Service Module for E1 Operation Transmit Clocking Normal clock or Srts generated Line Coding Electromagnetic Compatibility Physical and Electrical Characteristics for Cards EMC ConformanceNebs ATM Forum CES Circuit Emulations ServiceFrame Relay Environmental Safety Rx BNC Receive T3 from trunk Tx BNC Transmit T3 to trunk Connector DescriptionT3 Trunk Cabling Cable Parameter Description Pin No Description Frame Relay CablingT1 Cabling Rx BNC Receive E1 from trunk Tx BNC Transmit E1 to trunk SMB ConnectorE1 Cabling 12IN1-S4 V.35/X.21 Back Card Signal Name Source Pin No Name Signal Function Polarity Signal Source Hssi Port ConnectorsSignal Name DC Power Cabling Control and Clock Cabling AC Power CablingMaintenance and Control Ports Pin No Name Description External Alarm CablingExternal Clock Input Cabling T1 Clock Cabling Pin No Alarm Description Release 1.1.31, Part Number 78-11215-03 Rev. B0, May StrataView Plus More general Class of Service Buffer or CosBMonarch chip set GL-2 StrataCom IGX switch GL-3 Strictly correct AUSM/B AAL5APS Ausm AX-CESM-8E1 AX-CESM-8T1 Frsm cards Circuit Emulation Service ModuleCesm CIR MGX-FRSM-2E3T3 MGX-HS2/B Front cardsFrsm MGX-HS2/B MGX-AUSM/B-8E1MGX-AUSM/B-8T1 MGX-FRSM-2CT3 PXM-UI PARPXM PXM1-UI SRM-3T3 Sonet