Miscellaneous Controls | Clarity WN=5230-S manual

Clarity Visual Systems

Miscellaneous Controls

The Misc Control menu contains:

Sharpness

Buzzer Enable

Horizontal Flip

Vertical Flip

Auto Lamp On

Test Patterns

Source Select

Frequency

Phase

Input Level

Position

Zoom

Wall Processor

Color Balance

Curtain

Hours

Save Config

Recall Config

Reset Config

Misc Control

About

Misc Control

[X]	Sharpness
[X]	Buzzer Enable
[ ]	Flip Horz
[ ]	Flip Vert
[ ]	Auto Lamp On
[ ]	Test Patterns

The Misc Control menu contains several features that are enabled when an X is in the box. To put an X in a particular feature’s box, or to remove it, press the ENTER button when that item is highlighted.

Sharpness - When this feature is disabled, the computer video will be smoothed. This is done to reduce video noise and other artifacts that are present when the source resolution is expanded to fit the WN-5230-S or when the quality of the source signal is not very good. Phase and Frequency have little or no effect on the image with Sharpness disabled. With Sharpness enabled, it is very important to correctly set the Frequency and Phase of the display. In general, Sharpness should be ON for computer sources, OFF for composite and S-video sources.

62September 1999

Image 70

Clarity WN=5230-S manual Miscellaneous Controls

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Product Introduction Introduction Options and Accessories Safety Warnung Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Power Site Preparation Power Consumption Voltage Range Flooring Temperature and HumidityClearance Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, left side wider Keystone, top widerKeystone, bottom wider Keystone, right side wider Size Up, down, right, left Keystone Adjustment SummaryRotation Final Position WN-5230-S VideoWall User’s Guide Mechanical Setup Mechanical Setup, Standard Screen Slip fingers between the screen frame Using both hands…Grasp the screen on each side at the bottom For added stability… Mechanical Setup, Ultra-Thin Mullion or Blackscreen Reinstall screens Alignment Procedure in Detail Basic Steps for Alignment Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Power-On Operation Adjust the Input Signal Settings Operation On the remote control, press Source Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Input Level Display an all-white image from the signal source Adjust the White Input Level PC, MAC or Rgbs DataSelect Auto Exit from the Black Level menu Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Saturation Adjust Hue Set the Sharpness Adjust the Frequency Turn Sharpness on Adjust the Phase Press Prev Menu Position the Image Zoom Arrow keys Press Enter Adjust the ColorsPress the Up/Down Scale the image Color Increase will Decrease will System Adjust the nextBright display Displays WN-5230-S VideoWall User’s Guide Save, Recall, or Reset the Settings Save 800x600 Save Are you sure? Yes No Sure Turning off the Main Power Switch Turning off the Display, Entering Standby ModeTurning off the System WN-5230-S VideoWall User’s Guide Clarity’s Big Picture Disable wall modeReset Zoom Center the image Build the wall Set the Wall Size on each display Wall Processor Save the settings Loop-Thru of Source Video LOOP-THRU Plug in the connector Installing Big Picture Option KeyTurn off the power Turn on power Other Features Adjustments Curtain Press MON SEL On the remote Enable MonitorMonitor Select Select Miscellaneous Controls Off Reset Lamp Hours Keys About Cleaning and Maintenance Lamp Screen frame Lamp Replacement, Front, Standard Mullion ScreensAccess door Compartment hood Removing a Standard Screen Using the Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type SRT-100, Screen Removal Tool Air Filter Replacement, Front Access Air Filter Access cover Cleaning the Screen and MirrorsAir Filter Replacement, Rear Access Remove the rear Troubleshooting Power and Start-Up Problems Switch AC power toTurn on main power Standby-delay mode Start sending Electronics turnOn the DLP engine Data to it Standby LED Fan LED Lamp LED Indication Image Problems Follow these steps in order. Check WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Connector Pinouts Rgbs MAC RS-232 RS-232 OUT Video Rear Panel Indicators Rear Panel Indicators, Connectors and ControlsInterface and Controls Source Rear Panel Connectors Connector Description Remote-Control Remote Control FunctionsRear Panel Controls Remote Button Description On-Screen Menus and Messages Frequency Source Absent Menus BNC Rgbs This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Commands RS-232 Control Items RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Specifications Optical Mechanical Environmental Picture Control Electrical BNC Regulatory Information Declaration of Conformity FCC Regulations Other Certifications Index ACK 113 VGA