Save Are you sure? Yes No Sure | Clarity WN=5230-S guide

WN-5230-S VideoWall User’s Guide

1.Press the remote control MENU button

2.Press the Up/Down arrow keys

3.Press ENTER

4.Press the Up/Down arrow keys to highlight the upper pair of arrows # ∃

5.Press the Left/Right arrow keys

6.Press the Up/Down arrow keys to highlight the lower pair of arrows # ∃

7.Press the Left/Right arrow keys

8.Press the Up/Down arrow keys to highlight Save (or Recall or Reset)

The Main menu is displayed.

Move the cursor to the Save Config (or Recall Config or Reset Config) selection.

The Save Config (or Recall Config or Reset Config) menu is displayed.

This is the Source selection area. The list of sources is shown in the right column, with the current selection preceded by a bullet • and stated next to the arrow symbols.

Use the left/right buttons to choose the Source you want to Save/Recall/Reset.

This is the Mode selection area, where you will choose the modes that will be Saved/Recalled/Reset for the previously selected Source. There is a separate memory for each source in each mode.

Use the left/right buttons to choose the Mode you want to Save/Recall/Reset. (If the Source is “ALL,” the only choice for Mode is also “ALL.”)

Press ENTER. A new menu appears as shown below.

Save Configuration

# ∃ PC

# ∃ ALL

Save

Are you sure?

Yes No

Sure

9.Press the Left/Right arrow keys to highlight Yes

Press ENTER. The settings will be saved/recalled/reset for the Sources and Modes you chose.

Shortcut: Unless you have made changes to a source or mode that you do not want to save, it is easiest and safest to Save All sources, All modes.

Note: Resetting to factory default settings does not destroy the saved settings in memory until you Save them.

51

Image 59

Clarity WN=5230-S manual Save Are you sure? Yes No Sure

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Introduction Product Introduction Options and Accessories Warnung Safety Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Site Preparation Power Voltage Range Power Consumption Clearance Temperature and HumidityFlooring Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, right side wider Keystone, top widerKeystone, bottom wider Keystone, left side wider Up, down, right, left Size Final Position Adjustment SummaryRotation Keystone WN-5230-S VideoWall User’s Guide Mechanical Setup, Standard Screen Mechanical Setup For added stability… Using both hands…Grasp the screen on each side at the bottom Slip fingers between the screen frame Reinstall screens Mechanical Setup, Ultra-Thin Mullion or Blackscreen Basic Steps for Alignment Alignment Procedure in Detail Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Operation Power-On Operation Adjust the Input Signal Settings Source On the remote control, press Input Level Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Select Auto Exit from the Black Level menu Adjust the White Input Level PC, MAC or Rgbs DataDisplay an all-white image from the signal source Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Hue Adjust Saturation Set the Sharpness Turn Sharpness on Adjust the Frequency Press Prev Menu Adjust the Phase Position the Image Zoom Scale the image Adjust the ColorsPress the Up/Down Arrow keys Press Enter Color Increase will Decrease will Displays Adjust the nextBright display System WN-5230-S VideoWall User’s Guide Save 800x600 Save, Recall, or Reset the Settings Save Are you sure? Yes No Sure Turning off the System Turning off the Display, Entering Standby ModeTurning off the Main Power Switch WN-5230-S VideoWall User’s Guide Build the wall Disable wall modeReset Zoom Center the image Clarity’s Big Picture Set the Wall Size on each display Wall Processor Loop-Thru of Source Video Save the settings LOOP-THRU Turn on power Installing Big Picture Option KeyTurn off the power Plug in the connector Curtain Other Features Adjustments Select On the remote Enable MonitorMonitor Select Press MON SEL Miscellaneous Controls Off Keys Reset Lamp Hours About Lamp Cleaning and Maintenance Compartment hood Lamp Replacement, Front, Standard Mullion ScreensAccess door Screen frame Removing a Standard Screen Using the Screen Removal Tool SRT-100, Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type Air Filter Air Filter Replacement, Front Access Remove the rear Cleaning the Screen and MirrorsAir Filter Replacement, Rear Access Access cover Power and Start-Up Problems Troubleshooting Standby-delay mode AC power toTurn on main power Switch Data to it Electronics turnOn the DLP engine Start sending Standby LED Fan LED Lamp LED Indication Follow these steps in order. Check Image Problems WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Rgbs Connector Pinouts MAC RS-232 OUT RS-232 Video Interface and Controls Rear Panel Indicators, Connectors and ControlsRear Panel Indicators Source Connector Description Rear Panel Connectors Rear Panel Controls Remote Control FunctionsRemote-Control Remote Button Description Frequency On-Screen Menus and Messages Source Absent BNC Rgbs Menus This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Control Items RS-232 Commands RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Optical Specifications Mechanical Picture Control Environmental BNC Electrical Declaration of Conformity Regulatory Information Other Certifications FCC Regulations ACK Index 113 VGA