Quick Start | Clarity WN=5230-S instruction

Clarity Visual Systems

Quick Start

This is a brief sequence of actions that must be followed to properly setup the WN-5230-S. Complete instructions and explanations of the steps are contained in the following chapters.

1

2

3

4

5

6

7

8

Remove the screens and build the wall starting with the lower row. Bolt the displays together side-to-side. If you have Ultra-Thin Mullion screens, align the displays and their adapter plates. Replace the screens.

Attach the power cable and video/data cables to the rear connector panel.

Connect the video/data cables to the source.

Plug the power cable into the wall outlet or other suitable power source. Remember that each display can draw as much as 1.7 amps at 115 volts (0.9 amps at 230V).

Turn on the display’s main AC power switch and wait for the 30 second standby-delay to elapse. The lighted power switch indicates when AC power is applied and the switch is on.

After the 30 second standby-delay has elapsed, press the remote control’s ON button to turn-on the display.

Select the SOURCE in the menu.

Use LEVEL ADJUST to calibrate the display to the source. Always adjust black before white!

Display a black image from the source and auto-adjust the BLACK LEVEL.

Display a white image from the source and auto-adjust the WHITE LEVEL.

8September 1999

Image 16

Clarity WN=5230-S manual Quick Start

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Product Introduction Introduction Options and Accessories Safety Warnung Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Power Site Preparation Power Consumption Voltage Range Flooring Temperature and HumidityClearance Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, top wider Keystone, bottom widerKeystone, left side wider Keystone, right side wider Size Up, down, right, left Adjustment Summary RotationKeystone Final Position WN-5230-S VideoWall User’s Guide Mechanical Setup Mechanical Setup, Standard Screen Using both hands… Grasp the screen on each side at the bottomSlip fingers between the screen frame For added stability… Mechanical Setup, Ultra-Thin Mullion or Blackscreen Reinstall screens Alignment Procedure in Detail Basic Steps for Alignment Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Power-On Operation Adjust the Input Signal Settings Operation On the remote control, press Source Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Input Level Display an all-white image from the signal source Adjust the White Input Level PC, MAC or Rgbs DataSelect Auto Exit from the Black Level menu Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Saturation Adjust Hue Set the Sharpness Adjust the Frequency Turn Sharpness on Adjust the Phase Press Prev Menu Position the Image Zoom Adjust the Colors Press the Up/DownArrow keys Press Enter Scale the image Color Increase will Decrease will Adjust the next Bright displaySystem Displays WN-5230-S VideoWall User’s Guide Save, Recall, or Reset the Settings Save 800x600 Save Are you sure? Yes No Sure Turning off the Main Power Switch Turning off the Display, Entering Standby ModeTurning off the System WN-5230-S VideoWall User’s Guide Disable wall mode Reset Zoom Center the imageClarity’s Big Picture Build the wall Set the Wall Size on each display Wall Processor Save the settings Loop-Thru of Source Video LOOP-THRU Installing Big Picture Option Key Turn off the powerPlug in the connector Turn on power Other Features Adjustments Curtain On the remote Enable Monitor Monitor SelectPress MON SEL Select Miscellaneous Controls Off Reset Lamp Hours Keys About Cleaning and Maintenance Lamp Lamp Replacement, Front, Standard Mullion Screens Access doorScreen frame Compartment hood Removing a Standard Screen Using the Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type SRT-100, Screen Removal Tool Air Filter Replacement, Front Access Air Filter Cleaning the Screen and Mirrors Air Filter Replacement, Rear AccessAccess cover Remove the rear Troubleshooting Power and Start-Up Problems AC power to Turn on main powerSwitch Standby-delay mode Electronics turn On the DLP engineStart sending Data to it Standby LED Fan LED Lamp LED Indication Image Problems Follow these steps in order. Check WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Connector Pinouts Rgbs MAC RS-232 RS-232 OUT Video Rear Panel Indicators Rear Panel Indicators, Connectors and ControlsInterface and Controls Source Rear Panel Connectors Connector Description Remote-Control Remote Control FunctionsRear Panel Controls Remote Button Description On-Screen Menus and Messages Frequency Source Absent Menus BNC Rgbs This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Commands RS-232 Control Items RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Specifications Optical Mechanical Environmental Picture Control Electrical BNC Regulatory Information Declaration of Conformity FCC Regulations Other Certifications Index ACK 113 VGA