Clarity WN=5230-S Reset Lamp Hours

Clarity Visual Systems

September 1999

64

Reset Lamp Hours

After you change the lamp, use this menu to reset the lamp hour timer

to zero. Lamp hours count up whenever the VideoWall is running (FAN

and LAMP LEDs are on). The system hour timer displays the total

hours that power has been applied to the VideoWall with the power

supply switch on. The system hour timer cannot be reset.

Source Select

Frequency

Phase

Input Level

Position

Zoom

Wall Processor

Color Balance

Curtain

Hours

Save Config

Recall Config

Reset Config

Misc Control

About

Lamp Hours: 5987:34

System Hours: 10886:29

Reset Lamp Hours?

[ ] Yes [X] No

1. Press the MAIN MENU

button on the remote The Main menu is displayed.

2. Press the up/down

arrow keys Move the cursor to the Hours selection.

3. Press ENTER The Lamp Hours menu displays the current number of

lamp operating hours. Replace the lamp at 8,000 hours.

This menu also shows total system hours.

4. Press left/right arrow

keys Use the left or right arrow keys to highlight the Yes

selection.

5. Press ENTER Press the ENTER button to proceed in resetting the lamp

hours to zero.

6. Press left/right arrow

keys At this point a warning will prompt ‘Did You Replace The

Lamp?’ If the lamp was replaced, use the left or right

arrow keys to highlight the Yes selection.

7. Press ENTER Press the ENTER button to proceed in resetting the lamp

hours to zero.

Contents

Main 52 VideoWall Digital Light ProcessingTM Display WN-5230-S Guide 070-0037-00 Page LIMITED WARRANTY LIMITATIONS. ANY WRITTEN WARRANTY OFFERED BY CLARITY IS IN LIEU OF ALL Page Table of Contents Page Page Page Product Introduction Introduction Features Options and Accessories Safety Page Page Page Page Quick Start Page Site Preparation Power Power Consumption Voltage Range Temperature and Humidity Flooring Clearance Cables and Signals Optical Alignment Tools Page Page Adjusting the Image Page Size Up, down, right, left Adjustment Summary (Viewed from the front) Final Position Size Rotation Page Mechanical Setup Mechanical Setup, Standard Screen To setup the WN-5230-S display in a video wall configuration, follow these steps: Mechanical Setup, Ultra-Thin Mullion or Blackscreen Basic Steps for Alignment Alignment Procedure in Detail Page Page Page Page Page Page Operation Step 1 Power-On Step 2 - Adjust the Input Signal Settings Select the Source here.) upper Input Level Adjust the Black Input Level - PC, MAC or RGBS Data Adjust the White Input Level - PC, MAC or RGBS Data Comp Video/S-Video Level Adjustment Hue: Changes the tint of images to be more green or more magenta colored. Note: When using Video Controls, the Phase control does not affect the image at all. Set the Sharpness Adjust the Frequency Use the FREQ function to adjust the images horizontal width. For Computer (PC or MAC) sources Adjust the Phase Position the Image Use the arrow keys to adjust the position of the image on each display. Zoom Step 3 - Adjust the Colors Note: It is a good idea to read this whole section before you start color balancing. Page all Page Step 4 Save, Recall, or Reset the Settings Turning off the System Turning off the Display, Entering Standby Mode Turning off the Main Power Switch Page Claritys Big Picture Wall Processor Setup Instructions you will see a menu like this: If this unit does not have Big Picture, you will see a menu like this: Loop-Thru of Source Video Page Installing Big Picture Option Key Other Features and Adjustments The following features and adjustments are available via the remote. To show program material again, repeat steps 1 and 2. Curtain Monitor Select ID Miscellaneous Controls Page Reset Lamp Hours About Cleaning and Maintenance Lamp Lamp Replacement, Front, Standard Mullion Screens Removing a Standard Screen Using the Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type Air Filter Air Filter Replacement, Front Access Air Filter Replacement, Rear Access Cleaning the Screen and Mirrors Troubleshooting Power and Start-Up Problems WN-5230-S VideoWall Users Guide 73 Fan turns on Page Page Image Problems Page Technical Support Connector Pinouts MAC PC & LOOP-THRU RS-232 IN RS-232 OUT S-VIDEO Interface and Controls Rear Panel Indicators, Connectors and Controls Rear Panel Indicators Page Rear Panel Connectors Rear Panel Controls Remote-Control Remote Control Functions Clarity Visual Systems 88 Remote Button Description On-Screen Menus and Messages Clarity Visual Systems 90 SOURCE ABSENT Menus Main Menu Clarity Visual Systems 92 Frequency Select Phase Select WN-5230-S VideoWall Users Guide 93 Color Balance * Curtain Select Clarity Visual Systems 94 Wall Processor Save Config WN-5230-S VideoWall Users Guide 95 Recall Config Clarity Visual Systems 96 Reset Config Page RS-232 Control Page Page WN-5230-S VideoWall Users Guide 101 RS-232 Control Items Function RS-232 COMMANDS RS-232 DATA Comments Page Page Page Page Specifications Optical Mechanical Environmental Picture Control Electrical Regulatory Information Declaration of Conformity FCC Regulations Other Certifications Index