Clarity WN=5230-S Menus

WN-5230-S VideoWall User’s Guide

91

Menus

Notes for menu descriptions:

* This command is also available from a special button on the remote control.

† In the Color Balance menu, the up-down arrows move the highlight through the two

columns. The left-right arrows change the highlighted value.

‡ This command is available only from a special button on the remote control.

§ The numbers in this menu are for ref erence only; they are not measurements.

Main Menu

Source* Opens the Source Select menu

Frequency* Opens the Frequency adjust window

Phase* Opens the Phase adjust window

Input Level* Opens Input Level menu (when PC, MAC or RGBS is the selected

source) or Video Controls menu (when Composite or S-video is the

selected source)

Position Opens the Position window

Zoom Opens the Zoom menu

Wall Processor Opens the Wall Processor menu

Color Balance* Opens the Color Balance menu

Curtain* Opens Curtain menu

Hours Opens Hours menu

Save Config Opens Save Config(uration) menu

Recall Config Opens Recall Config(uration) menu

Reset Config* Opens Reset Config(uration) menu

Misc Control Opens Misc(ellaneous) Control menu

About Opens About menu

Source Select

#

##

# $

$$

$ [source] [source] is one of the following:

PC

MAC

9-pin (RGBS)

BNC (RGBS)

C-Video

S-Video

#

##

# $

$$

$ [mode] [mode] is one of the following:

640x480

800x600

525/60Hz

625/50Hz

[ ] Auto Detects and sets the mode parameters for a selected source

[ ] Sync on Green Forces Sync on Green for RGBS, in case auto detection does not find

this correctly

[ ] Interlace Indicates that the source video is interlaced; cannot by changed

manually.

H Freq: 00000 Shows H rate in Hertz of selected source

Lines: 000 Shows total number of horizontal lines in the selected source

V Freq: 00 Shows frame rate in Hertz of selected source

Contents

Main 52 VideoWall Digital Light ProcessingTM Display WN-5230-S Guide 070-0037-00 Page LIMITED WARRANTY LIMITATIONS. ANY WRITTEN WARRANTY OFFERED BY CLARITY IS IN LIEU OF ALL Page Table of Contents Page Page Page Product Introduction Introduction Features Options and Accessories Safety Page Page Page Page Quick Start Page Site Preparation Power Power Consumption Voltage Range Temperature and Humidity Flooring Clearance Cables and Signals Optical Alignment Tools Page Page Adjusting the Image Page Size Up, down, right, left Adjustment Summary (Viewed from the front) Final Position Size Rotation Page Mechanical Setup Mechanical Setup, Standard Screen To setup the WN-5230-S display in a video wall configuration, follow these steps: Mechanical Setup, Ultra-Thin Mullion or Blackscreen Basic Steps for Alignment Alignment Procedure in Detail Page Page Page Page Page Page Operation Step 1 Power-On Step 2 - Adjust the Input Signal Settings Select the Source here.) upper Input Level Adjust the Black Input Level - PC, MAC or RGBS Data Adjust the White Input Level - PC, MAC or RGBS Data Comp Video/S-Video Level Adjustment Hue: Changes the tint of images to be more green or more magenta colored. Note: When using Video Controls, the Phase control does not affect the image at all. Set the Sharpness Adjust the Frequency Use the FREQ function to adjust the images horizontal width. For Computer (PC or MAC) sources Adjust the Phase Position the Image Use the arrow keys to adjust the position of the image on each display. Zoom Step 3 - Adjust the Colors Note: It is a good idea to read this whole section before you start color balancing. Page all Page Step 4 Save, Recall, or Reset the Settings Turning off the System Turning off the Display, Entering Standby Mode Turning off the Main Power Switch Page Claritys Big Picture Wall Processor Setup Instructions you will see a menu like this: If this unit does not have Big Picture, you will see a menu like this: Loop-Thru of Source Video Page Installing Big Picture Option Key Other Features and Adjustments The following features and adjustments are available via the remote. To show program material again, repeat steps 1 and 2. Curtain Monitor Select ID Miscellaneous Controls Page Reset Lamp Hours About Cleaning and Maintenance Lamp Lamp Replacement, Front, Standard Mullion Screens Removing a Standard Screen Using the Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type Air Filter Air Filter Replacement, Front Access Air Filter Replacement, Rear Access Cleaning the Screen and Mirrors Troubleshooting Power and Start-Up Problems WN-5230-S VideoWall Users Guide 73 Fan turns on Page Page Image Problems Page Technical Support Connector Pinouts MAC PC & LOOP-THRU RS-232 IN RS-232 OUT S-VIDEO Interface and Controls Rear Panel Indicators, Connectors and Controls Rear Panel Indicators Page Rear Panel Connectors Rear Panel Controls Remote-Control Remote Control Functions Clarity Visual Systems 88 Remote Button Description On-Screen Menus and Messages Clarity Visual Systems 90 SOURCE ABSENT Menus Main Menu Clarity Visual Systems 92 Frequency Select Phase Select WN-5230-S VideoWall Users Guide 93 Color Balance * Curtain Select Clarity Visual Systems 94 Wall Processor Save Config WN-5230-S VideoWall Users Guide 95 Recall Config Clarity Visual Systems 96 Reset Config Page RS-232 Control Page Page WN-5230-S VideoWall Users Guide 101 RS-232 Control Items Function RS-232 COMMANDS RS-232 DATA Comments Page Page Page Page Specifications Optical Mechanical Environmental Picture Control Electrical Regulatory Information Declaration of Conformity FCC Regulations Other Certifications Index