About | Clarity WN=5230-S specs

WN-5230-S VideoWall User’s Guide

About

This displays the Clarity Visual Systems contact information. It also displays the version of firmware being used. (The Project and Build information is of concern only to manufacturing.)

Source Select

Frequency

Phase

Input Level

Position

Zoom

Wall Processor

Color Balance

Curtain

Hours

Save Config

Recall Config

Reset Config

Misc Control

About

Clarity Visual Systems

9025 SW Hillman Court

Suite 3122

Wilsonville, OR 97070

USA

Tel(503) 570-0700

Web www.ClarityVisual.com

Project: 573-0650-00

Version: Rev A

Config: C1A5P3N6

Build: 0036

Date: Fri, Mar 12, 1999

65

Image 73

Clarity WN=5230-S manual About

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Introduction Product Introduction Options and Accessories Warnung Safety Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Site Preparation Power Voltage Range Power Consumption Flooring Temperature and HumidityClearance Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, bottom wider Keystone, top widerKeystone, left side wider Keystone, right side wider Up, down, right, left Size Rotation Adjustment SummaryKeystone Final Position WN-5230-S VideoWall User’s Guide Mechanical Setup, Standard Screen Mechanical Setup Grasp the screen on each side at the bottom Using both hands…Slip fingers between the screen frame For added stability… Reinstall screens Mechanical Setup, Ultra-Thin Mullion or Blackscreen Basic Steps for Alignment Alignment Procedure in Detail Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Operation Power-On Operation Adjust the Input Signal Settings Source On the remote control, press Input Level Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Display an all-white image from the signal source Adjust the White Input Level PC, MAC or Rgbs DataSelect Auto Exit from the Black Level menu Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Hue Adjust Saturation Set the Sharpness Turn Sharpness on Adjust the Frequency Press Prev Menu Adjust the Phase Position the Image Zoom Press the Up/Down Adjust the ColorsArrow keys Press Enter Scale the image Color Increase will Decrease will Bright display Adjust the nextSystem Displays WN-5230-S VideoWall User’s Guide Save 800x600 Save, Recall, or Reset the Settings Save Are you sure? Yes No Sure Turning off the Main Power Switch Turning off the Display, Entering Standby ModeTurning off the System WN-5230-S VideoWall User’s Guide Reset Zoom Center the image Disable wall modeClarity’s Big Picture Build the wall Set the Wall Size on each display Wall Processor Loop-Thru of Source Video Save the settings LOOP-THRU Turn off the power Installing Big Picture Option KeyPlug in the connector Turn on power Curtain Other Features Adjustments Monitor Select On the remote Enable MonitorPress MON SEL Select Miscellaneous Controls Off Keys Reset Lamp Hours About Lamp Cleaning and Maintenance Access door Lamp Replacement, Front, Standard Mullion ScreensScreen frame Compartment hood Removing a Standard Screen Using the Screen Removal Tool SRT-100, Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type Air Filter Air Filter Replacement, Front Access Air Filter Replacement, Rear Access Cleaning the Screen and MirrorsAccess cover Remove the rear Power and Start-Up Problems Troubleshooting Turn on main power AC power toSwitch Standby-delay mode On the DLP engine Electronics turnStart sending Data to it Standby LED Fan LED Lamp LED Indication Follow these steps in order. Check Image Problems WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Rgbs Connector Pinouts MAC RS-232 OUT RS-232 Video Rear Panel Indicators Rear Panel Indicators, Connectors and ControlsInterface and Controls Source Connector Description Rear Panel Connectors Remote-Control Remote Control FunctionsRear Panel Controls Remote Button Description Frequency On-Screen Menus and Messages Source Absent BNC Rgbs Menus This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Control Items RS-232 Commands RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Optical Specifications Mechanical Picture Control Environmental BNC Electrical Declaration of Conformity Regulatory Information Other Certifications FCC Regulations ACK Index 113 VGA