Interface and Controls, Rear Panel Indicators | Clarity WN=5230-S

Clarity Visual Systems

Interface and Controls

Rear Panel Indicators, Connectors and Controls

The rear panel of the WN-5230-S VideoWall display is depicted below. The S-Video and Composite Video inputs are part of the VIM-300 option. If your units do not have this option, these connector ports will be empty.

Rear Panel Indicators

Indicator	Description

STBY	The green STBY light emitting diode (LED) is on steady
	when unit is in Standby mode and main electrical power is
	switched on. This LED blinks for 30 seconds when the
	main power is initially switched on or when the lamp is
	switched off to enter Standby mode. When it is blinking,
	the power on button for the lamp is inhibited.
	This LED will blink at a faster rate when the lamp is being
	ignited.

FAN	This is a green LED that is on when the cooling fan is
	running. It remains on for the 30 second cool-down cycle
	after the lamp is switched off. It is on during the initial
	30-second period after AC power is applied.

LAMP	This is also a green LED. It is on when the display
	electronics has turned on the projection lamp.

TEMP	(Not functional in the WN-5230-S)

REMOTE	Indicates activity of the IR sensor. Stray Infrared radiation
	causes a faint glow and flicker. A signal from the Remote
	Control causes a 1/10th second flash.

84September 1999

Image 92

Clarity WN=5230-S manual Interface and Controls, Rear Panel Indicators, Connectors and Controls

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Product Introduction Introduction Options and Accessories Safety Warnung Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Power Site Preparation Power Consumption Voltage Range Clearance Temperature and HumidityFlooring Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, top wider Keystone, bottom widerKeystone, left side wider Keystone, right side wider Size Up, down, right, left Adjustment Summary RotationKeystone Final Position WN-5230-S VideoWall User’s Guide Mechanical Setup Mechanical Setup, Standard Screen Using both hands… Grasp the screen on each side at the bottomSlip fingers between the screen frame For added stability… Mechanical Setup, Ultra-Thin Mullion or Blackscreen Reinstall screens Alignment Procedure in Detail Basic Steps for Alignment Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Power-On Operation Adjust the Input Signal Settings Operation On the remote control, press Source Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Input Level Select Auto Exit from the Black Level menu Adjust the White Input Level PC, MAC or Rgbs DataDisplay an all-white image from the signal source Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Saturation Adjust Hue Set the Sharpness Adjust the Frequency Turn Sharpness on Adjust the Phase Press Prev Menu Position the Image Zoom Adjust the Colors Press the Up/DownArrow keys Press Enter Scale the image Color Increase will Decrease will Adjust the next Bright displaySystem Displays WN-5230-S VideoWall User’s Guide Save, Recall, or Reset the Settings Save 800x600 Save Are you sure? Yes No Sure Turning off the System Turning off the Display, Entering Standby ModeTurning off the Main Power Switch WN-5230-S VideoWall User’s Guide Disable wall mode Reset Zoom Center the imageClarity’s Big Picture Build the wall Set the Wall Size on each display Wall Processor Save the settings Loop-Thru of Source Video LOOP-THRU Installing Big Picture Option Key Turn off the powerPlug in the connector Turn on power Other Features Adjustments Curtain On the remote Enable Monitor Monitor SelectPress MON SEL Select Miscellaneous Controls Off Reset Lamp Hours Keys About Cleaning and Maintenance Lamp Lamp Replacement, Front, Standard Mullion Screens Access doorScreen frame Compartment hood Removing a Standard Screen Using the Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type SRT-100, Screen Removal Tool Air Filter Replacement, Front Access Air Filter Cleaning the Screen and Mirrors Air Filter Replacement, Rear AccessAccess cover Remove the rear Troubleshooting Power and Start-Up Problems AC power to Turn on main powerSwitch Standby-delay mode Electronics turn On the DLP engineStart sending Data to it Standby LED Fan LED Lamp LED Indication Image Problems Follow these steps in order. Check WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Connector Pinouts Rgbs MAC RS-232 RS-232 OUT Video Interface and Controls Rear Panel Indicators, Connectors and ControlsRear Panel Indicators Source Rear Panel Connectors Connector Description Rear Panel Controls Remote Control FunctionsRemote-Control Remote Button Description On-Screen Menus and Messages Frequency Source Absent Menus BNC Rgbs This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Commands RS-232 Control Items RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Specifications Optical Mechanical Environmental Picture Control Electrical BNC Regulatory Information Declaration of Conformity FCC Regulations Other Certifications Index ACK 113 VGA