Monitor Select, Press MON SEL | Clarity WN=5230-S guide

WN-5230-S VideoWall User’s Guide

Monitor Select

Disables most remote functions on the display to prevent the unit from unintended adjustment via the remote control.

1.	Press MON SEL	The Monitor Select menu is displayed.
	on the remote

2.	Enable Monitor	Press the ENTER button to enable the Monitor Select
	Select	feature.

To restore full remote functionality, follow steps 1 and 2 again to disable the Monitor Select feature. Monitor Select is not available on the main menu.

ID

This menu item displays the current Monitor ID address of the WN-5230-S. The Monitor ID is set with the 2 Monitor ID knobs on the back of the display. The Monitor ID menu displays the address as the Group and Unit which corresponds with the knob settings on the back of the display. ID is not available on the main menu.

1.Press ID on the Remote

Displays the Monitor ID position as selected by the Monitor ID switch in the rear of the unit.

61

Image 69

Clarity WN=5230-S manual Monitor Select, Press MON SEL, On the remote Enable Monitor, Press ID on the Remote

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Introduction Product Introduction Options and Accessories Warnung Safety Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Site Preparation Power Voltage Range Power Consumption Temperature and Humidity FlooringClearance Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, bottom wider Keystone, top widerKeystone, left side wider Keystone, right side wider Up, down, right, left Size Rotation Adjustment SummaryKeystone Final Position WN-5230-S VideoWall User’s Guide Mechanical Setup, Standard Screen Mechanical Setup Grasp the screen on each side at the bottom Using both hands…Slip fingers between the screen frame For added stability… Reinstall screens Mechanical Setup, Ultra-Thin Mullion or Blackscreen Basic Steps for Alignment Alignment Procedure in Detail Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Operation Power-On Operation Adjust the Input Signal Settings Source On the remote control, press Input Level Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Adjust the White Input Level PC, MAC or Rgbs Data Display an all-white image from the signal sourceSelect Auto Exit from the Black Level menu Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Hue Adjust Saturation Set the Sharpness Turn Sharpness on Adjust the Frequency Press Prev Menu Adjust the Phase Position the Image Zoom Press the Up/Down Adjust the ColorsArrow keys Press Enter Scale the image Color Increase will Decrease will Bright display Adjust the nextSystem Displays WN-5230-S VideoWall User’s Guide Save 800x600 Save, Recall, or Reset the Settings Save Are you sure? Yes No Sure Turning off the Display, Entering Standby Mode Turning off the Main Power SwitchTurning off the System WN-5230-S VideoWall User’s Guide Reset Zoom Center the image Disable wall modeClarity’s Big Picture Build the wall Set the Wall Size on each display Wall Processor Loop-Thru of Source Video Save the settings LOOP-THRU Turn off the power Installing Big Picture Option KeyPlug in the connector Turn on power Curtain Other Features Adjustments Monitor Select On the remote Enable MonitorPress MON SEL Select Miscellaneous Controls Off Keys Reset Lamp Hours About Lamp Cleaning and Maintenance Access door Lamp Replacement, Front, Standard Mullion ScreensScreen frame Compartment hood Removing a Standard Screen Using the Screen Removal Tool SRT-100, Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type Air Filter Air Filter Replacement, Front Access Air Filter Replacement, Rear Access Cleaning the Screen and MirrorsAccess cover Remove the rear Power and Start-Up Problems Troubleshooting Turn on main power AC power toSwitch Standby-delay mode On the DLP engine Electronics turnStart sending Data to it Standby LED Fan LED Lamp LED Indication Follow these steps in order. Check Image Problems WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Rgbs Connector Pinouts MAC RS-232 OUT RS-232 Video Rear Panel Indicators, Connectors and Controls Rear Panel IndicatorsInterface and Controls Source Connector Description Rear Panel Connectors Remote Control Functions Remote-ControlRear Panel Controls Remote Button Description Frequency On-Screen Menus and Messages Source Absent BNC Rgbs Menus This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Control Items RS-232 Commands RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Optical Specifications Mechanical Picture Control Environmental BNC Electrical Declaration of Conformity Regulatory Information Other Certifications FCC Regulations ACK Index 113 VGA