Manuals / Clarity / TV and Video / Projection Television

Clarity WN=5230-S manual Mac

Models: WN=5230-S

1 122

Download 122 pages 61.95 Kb

Page 89

WN-5230-S VideoWall User’s Guide

MAC

1.	Ground	9.	Blue Video
2.	Red Video	10.	No Connect
3.	Horizontal Sync	11.	Ground
4.	Ground	12.	Vertical Sync
5.	Green Video	13.	Ground
6.	Ground	14.	Ground
7.	No Connect	15.	No Connect
8.	No Connect

PC & LOOP-THRU

1.	Red Video	9.	No Connect
1.	Red Video	10.	Ground
2.	Green Video	11.	No Connect
3.	Blue Video	12.	No Connect
4.	No Connect	13.	Horizontal Sync
5.	No Connect	14.	Vertical Sync
6.	Ground	15.	No Connect

7.Ground

8.Ground

81

Image 89

Clarity WN=5230-S manual Mac

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Introduction Product IntroductionOptions and Accessories Warnung SafetyGefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Site Preparation PowerVoltage Range Power ConsumptionClearance Temperature and HumidityFlooring Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, bottom wider Keystone, top widerKeystone, left side wider Keystone, right side widerUp, down, right, left SizeRotation Adjustment SummaryKeystone Final PositionWN-5230-S VideoWall User’s Guide Mechanical Setup, Standard Screen Mechanical SetupGrasp the screen on each side at the bottom Using both hands…Slip fingers between the screen frame For added stability…Reinstall screens Mechanical Setup, Ultra-Thin Mullion or BlackscreenBasic Steps for Alignment Alignment Procedure in DetailClarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Operation Power-OnOperation Adjust the Input Signal SettingsSource On the remote control, pressInput Level Input Level Adjust the Black Input Level PC, MAC or Rgbs DataSelect Auto Exit from the Black Level menu Adjust the White Input Level PC, MAC or Rgbs DataDisplay an all-white image from the signal source Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Hue Adjust SaturationSet the Sharpness Turn Sharpness on Adjust the FrequencyPress Prev Menu Adjust the PhasePosition the Image Zoom Press the Up/Down Adjust the ColorsArrow keys Press Enter Scale the imageColor Increase will Decrease will Bright display Adjust the nextSystem DisplaysWN-5230-S VideoWall User’s Guide Save 800x600 Save, Recall, or Reset the SettingsSave Are you sure? Yes No Sure Turning off the System Turning off the Display, Entering Standby ModeTurning off the Main Power Switch WN-5230-S VideoWall User’s Guide Reset Zoom Center the image Disable wall modeClarity’s Big Picture Build the wallSet the Wall Size on each display Wall Processor Loop-Thru of Source Video Save the settingsLOOP-THRU Turn off the power Installing Big Picture Option KeyPlug in the connector Turn on powerCurtain Other Features AdjustmentsMonitor Select On the remote Enable MonitorPress MON SEL SelectMiscellaneous Controls Off Keys Reset Lamp HoursAbout Lamp Cleaning and MaintenanceAccess door Lamp Replacement, Front, Standard Mullion ScreensScreen frame Compartment hoodRemoving a Standard Screen Using the Screen Removal Tool SRT-100, Screen Removal Tool Lamp Replacement, Rear Access, Any Screen TypeAir Filter Air Filter Replacement, Front AccessAir Filter Replacement, Rear Access Cleaning the Screen and MirrorsAccess cover Remove the rearPower and Start-Up Problems TroubleshootingTurn on main power AC power toSwitch Standby-delay modeOn the DLP engine Electronics turnStart sending Data to itStandby LED Fan LED Lamp LED Indication Follow these steps in order. Check Image ProblemsWN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Rgbs Connector PinoutsMAC RS-232 OUT RS-232Video Interface and Controls Rear Panel Indicators, Connectors and ControlsRear Panel Indicators Source Connector Description Rear Panel ConnectorsRear Panel Controls Remote Control FunctionsRemote-Control Remote Button Description Frequency On-Screen Menus and MessagesSource Absent BNC Rgbs MenusThis menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Control Items RS-232 CommandsRCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Optical SpecificationsMechanical Picture Control EnvironmentalBNC ElectricalDeclaration of Conformity Regulatory InformationOther Certifications FCC RegulationsACK Index113 VGA