Site Preparation, Power | Clarity WN=5230-S specs

Clarity Visual Systems

Site Preparation

Read the chapter on safety precautions before installing and operating the WN-5230-S VideoWall.

The following table shows the installation specifications for a variety of common video wall configurations.

Height X Width -		1X1	1X2	2x2	2X3	3X3	3X4	4X4
		Single	2 displays	4 displays	6 displays	9 displays	12 displays	16 displays
Screen Height,	inches	31.3	31.3	62.6	62.6	93.9	93.9	125.2
centimeters		79.5	79.5	159.0	159.0	238.5	238.5	318.0
Screen Width,	inches	41.7	83.4	83.4	125.1	125.1	166.8	166.8
centimeters		105.9	211.8	211.8	317.8	317.8	423.7	423.7
Weight,	pounds	120	240	480	720	1080	1440	1920
	kilograms	54.4	108.9	217.7	326.6	489.9	653.2	870.9
115 Volts A/C Input
Current, amps - max		1.7	3.4	7.0	10.4	15.7	20.9	27.8
Power, watts - typical		160	320	640	960	1440	1920	2560
Heat, BTU/hr - typical		546	1092	2184	3276	4914	6551	8735
Air Cond., tons - typical		.05	.09	.18	.27	.41	.55	.73
230 Volts A/C Input
Current, amps - max		.9	1.7	3.4	5.2	7.9	10.5	13.9
Power, watts - typical		160	320	640	960	1440	1920	2560
Heat, BTU/hr - typical		546	1092	2184	3276	4914	6551	8735
Air Cond., tons - typical		.05	.09	.18	.27	.41	.55	.73

Table 1

Power

Make sure that any power cord substituted for the power cord originally supplied with the display is compatible with the nominal power source used with the WN-5230-S.

10September 1999

Image 18

Clarity WN=5230-S manual Site Preparation, Power

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Product Introduction Introduction Options and Accessories Safety Warnung Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Power Site Preparation Power Consumption Voltage Range Temperature and Humidity FlooringClearance Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, left side wider Keystone, top widerKeystone, bottom wider Keystone, right side wider Size Up, down, right, left Keystone Adjustment SummaryRotation Final Position WN-5230-S VideoWall User’s Guide Mechanical Setup Mechanical Setup, Standard Screen Slip fingers between the screen frame Using both hands…Grasp the screen on each side at the bottom For added stability… Mechanical Setup, Ultra-Thin Mullion or Blackscreen Reinstall screens Alignment Procedure in Detail Basic Steps for Alignment Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Power-On Operation Adjust the Input Signal Settings Operation On the remote control, press Source Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Input Level Adjust the White Input Level PC, MAC or Rgbs Data Display an all-white image from the signal sourceSelect Auto Exit from the Black Level menu Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Saturation Adjust Hue Set the Sharpness Adjust the Frequency Turn Sharpness on Adjust the Phase Press Prev Menu Position the Image Zoom Arrow keys Press Enter Adjust the ColorsPress the Up/Down Scale the image Color Increase will Decrease will System Adjust the nextBright display Displays WN-5230-S VideoWall User’s Guide Save, Recall, or Reset the Settings Save 800x600 Save Are you sure? Yes No Sure Turning off the Display, Entering Standby Mode Turning off the Main Power SwitchTurning off the System WN-5230-S VideoWall User’s Guide Clarity’s Big Picture Disable wall modeReset Zoom Center the image Build the wall Set the Wall Size on each display Wall Processor Save the settings Loop-Thru of Source Video LOOP-THRU Plug in the connector Installing Big Picture Option KeyTurn off the power Turn on power Other Features Adjustments Curtain Press MON SEL On the remote Enable MonitorMonitor Select Select Miscellaneous Controls Off Reset Lamp Hours Keys About Cleaning and Maintenance Lamp Screen frame Lamp Replacement, Front, Standard Mullion ScreensAccess door Compartment hood Removing a Standard Screen Using the Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type SRT-100, Screen Removal Tool Air Filter Replacement, Front Access Air Filter Access cover Cleaning the Screen and MirrorsAir Filter Replacement, Rear Access Remove the rear Troubleshooting Power and Start-Up Problems Switch AC power toTurn on main power Standby-delay mode Start sending Electronics turnOn the DLP engine Data to it Standby LED Fan LED Lamp LED Indication Image Problems Follow these steps in order. Check WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Connector Pinouts Rgbs MAC RS-232 RS-232 OUT Video Rear Panel Indicators, Connectors and Controls Rear Panel IndicatorsInterface and Controls Source Rear Panel Connectors Connector Description Remote Control Functions Remote-ControlRear Panel Controls Remote Button Description On-Screen Menus and Messages Frequency Source Absent Menus BNC Rgbs This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Commands RS-232 Control Items RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Specifications Optical Mechanical Environmental Picture Control Electrical BNC Regulatory Information Declaration of Conformity FCC Regulations Other Certifications Index ACK 113 VGA