Ntsc PAL Secam | Clarity WN=5230-S specs

		WN-5230-S VideoWall User’s Guide

Recall Config
# ∃ [source]	Left-right arrows select source to recall:
	All
	PC
	MAC
	9-pin (RGBS)
	BNC (RGBS)
	C-video
	S-video
# ∃ [mode]	Left-right arrows select mode to recall:
	Source	Mode
	All	All [modes are recalled for all sources]
	PC	All [PC modes are recalled]
		640x480
		800x600
	MAC	All [MAC modes are recalled]
		640x480
		800x600
		832x624
	RGBS 9-pin	All [RGBS 9-pin modes are recalled]
		640x480
		800x600
		525/60Hz
		625/50Hz
	RGBS BNC	All [RGBS BNC modes are recalled]
		640x480
		800x600
		525/60Hz
		625/50Hz
	Composite	All [Composite modes are recalled]
		NTSC
		PAL
		SECAM
	S-Video	All [S-Video modes are recalled]
		NTSC
		PAL
		SECAM

95

Image 103

Clarity WN=5230-S manual Ntsc PAL Secam

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Introduction Product Introduction Options and Accessories Warnung Safety Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Site Preparation Power Voltage Range Power Consumption Flooring Temperature and HumidityClearance Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, right side wider Keystone, top widerKeystone, bottom wider Keystone, left side wider Up, down, right, left Size Final Position Adjustment SummaryRotation Keystone WN-5230-S VideoWall User’s Guide Mechanical Setup, Standard Screen Mechanical Setup For added stability… Using both hands…Grasp the screen on each side at the bottom Slip fingers between the screen frame Reinstall screens Mechanical Setup, Ultra-Thin Mullion or Blackscreen Basic Steps for Alignment Alignment Procedure in Detail Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Operation Power-On Operation Adjust the Input Signal Settings Source On the remote control, press Input Level Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Display an all-white image from the signal source Adjust the White Input Level PC, MAC or Rgbs DataSelect Auto Exit from the Black Level menu Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Hue Adjust Saturation Set the Sharpness Turn Sharpness on Adjust the Frequency Press Prev Menu Adjust the Phase Position the Image Zoom Scale the image Adjust the ColorsPress the Up/Down Arrow keys Press Enter Color Increase will Decrease will Displays Adjust the nextBright display System WN-5230-S VideoWall User’s Guide Save 800x600 Save, Recall, or Reset the Settings Save Are you sure? Yes No Sure Turning off the Main Power Switch Turning off the Display, Entering Standby ModeTurning off the System WN-5230-S VideoWall User’s Guide Build the wall Disable wall modeReset Zoom Center the image Clarity’s Big Picture Set the Wall Size on each display Wall Processor Loop-Thru of Source Video Save the settings LOOP-THRU Turn on power Installing Big Picture Option KeyTurn off the power Plug in the connector Curtain Other Features Adjustments Select On the remote Enable MonitorMonitor Select Press MON SEL Miscellaneous Controls Off Keys Reset Lamp Hours About Lamp Cleaning and Maintenance Compartment hood Lamp Replacement, Front, Standard Mullion ScreensAccess door Screen frame Removing a Standard Screen Using the Screen Removal Tool SRT-100, Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type Air Filter Air Filter Replacement, Front Access Remove the rear Cleaning the Screen and MirrorsAir Filter Replacement, Rear Access Access cover Power and Start-Up Problems Troubleshooting Standby-delay mode AC power toTurn on main power Switch Data to it Electronics turnOn the DLP engine Start sending Standby LED Fan LED Lamp LED Indication Follow these steps in order. Check Image Problems WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Rgbs Connector Pinouts MAC RS-232 OUT RS-232 Video Rear Panel Indicators Rear Panel Indicators, Connectors and ControlsInterface and Controls Source Connector Description Rear Panel Connectors Remote-Control Remote Control FunctionsRear Panel Controls Remote Button Description Frequency On-Screen Menus and Messages Source Absent BNC Rgbs Menus This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Control Items RS-232 Commands RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Optical Specifications Mechanical Picture Control Environmental BNC Electrical Declaration of Conformity Regulatory Information Other Certifications FCC Regulations ACK Index 113 VGA