Source Absent | Clarity WN=5230-S specs

Clarity Visual Systems

Menu Selection

Description

WN-5230-S may be power cycled without loosing the settings.

Recall Config	Recalls previous user-saved configuration settings.

Reset Config	Resets all of the display’s settings to the factory defaults.

Menu Selection		Description

Misc Control	Sharpness:	When unchecked, a low pass filter is present in the
		signal path. When checked, the low pass filter is
		bypassed.
	Buzzer Enable:	Turns on or off the function-indicator buzzer.
	Flip Horz:	Flips the image from right to left.
	Flip Vert:	Flips the image from top to bottom.
	Auto Lamp On:	As soon as AC power is applied to the WN-5230-S,
		the display will automatically turn on after the 30
		second standby-delay has elapsed (plus the Monitor
		ID delay time) if this box is checked.
	Test Patterns:	Opens a menu with internally generated test
		patterns. Note: These patterns cannot be used to do
		Input Level adjust.

About	Clarity Visual Systems (or OEM) address and phone number; firmware
	version

SOURCE ABSENT

This screen message is displayed when no signal is detected on the source that is presently selected. If this message is displayed, verify that the source is outputting a video signal and verify that the video cable is plugged in.

90September 1999

Image 98

Clarity WN=5230-S manual Source Absent

Contents

VideoWall Digital Light ProcessingTM Display Page Iii Page Table of Contents CLARITY’S BIG Picture RS-232 Control Viii Product Introduction Introduction Options and Accessories Safety Warnung Gefahr Warnung Clarity Visual Systems WN-5230-S VideoWall User’s Guide Quick Start WN-5230-S VideoWall User’s Guide Power Site Preparation Power Consumption Voltage Range Clearance Temperature and HumidityFlooring Cables and Signals Optical Alignment LD1 LS1 LS2 LD2 Adjusting the Image Keystone, left side wider Keystone, top widerKeystone, bottom wider Keystone, right side wider Size Up, down, right, left Keystone Adjustment SummaryRotation Final Position WN-5230-S VideoWall User’s Guide Mechanical Setup Mechanical Setup, Standard Screen Slip fingers between the screen frame Using both hands…Grasp the screen on each side at the bottom For added stability… Mechanical Setup, Ultra-Thin Mullion or Blackscreen Reinstall screens Alignment Procedure in Detail Basic Steps for Alignment Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Clarity Visual Systems WN-5230-S VideoWall User’s Guide Power-On Operation Adjust the Input Signal Settings Operation On the remote control, press Source Input Level Adjust the Black Input Level PC, MAC or Rgbs Data Input Level Select Auto Exit from the Black Level menu Adjust the White Input Level PC, MAC or Rgbs DataDisplay an all-white image from the signal source Comp Video/S-Video Level Adjustment WN-5230-S VideoWall User’s Guide Adjust Saturation Adjust Hue Set the Sharpness Adjust the Frequency Turn Sharpness on Adjust the Phase Press Prev Menu Position the Image Zoom Arrow keys Press Enter Adjust the ColorsPress the Up/Down Scale the image Color Increase will Decrease will System Adjust the nextBright display Displays WN-5230-S VideoWall User’s Guide Save, Recall, or Reset the Settings Save 800x600 Save Are you sure? Yes No Sure Turning off the System Turning off the Display, Entering Standby ModeTurning off the Main Power Switch WN-5230-S VideoWall User’s Guide Clarity’s Big Picture Disable wall modeReset Zoom Center the image Build the wall Set the Wall Size on each display Wall Processor Save the settings Loop-Thru of Source Video LOOP-THRU Plug in the connector Installing Big Picture Option KeyTurn off the power Turn on power Other Features Adjustments Curtain Press MON SEL On the remote Enable MonitorMonitor Select Select Miscellaneous Controls Off Reset Lamp Hours Keys About Cleaning and Maintenance Lamp Screen frame Lamp Replacement, Front, Standard Mullion ScreensAccess door Compartment hood Removing a Standard Screen Using the Screen Removal Tool Lamp Replacement, Rear Access, Any Screen Type SRT-100, Screen Removal Tool Air Filter Replacement, Front Access Air Filter Access cover Cleaning the Screen and MirrorsAir Filter Replacement, Rear Access Remove the rear Troubleshooting Power and Start-Up Problems Switch AC power toTurn on main power Standby-delay mode Start sending Electronics turnOn the DLP engine Data to it Standby LED Fan LED Lamp LED Indication Image Problems Follow these steps in order. Check WN-5230-S VideoWall User’s Guide Technical Support Technical Support Request Connector Pinouts Rgbs MAC RS-232 RS-232 OUT Video Interface and Controls Rear Panel Indicators, Connectors and ControlsRear Panel Indicators Source Rear Panel Connectors Connector Description Rear Panel Controls Remote Control FunctionsRemote-Control Remote Button Description On-Screen Menus and Messages Frequency Source Absent Menus BNC Rgbs This menu shown only when selected source is PC, MAC or Rgbs Yes, then press Enter Ntsc Ntsc PAL Secam Left-right arrows select source to reset WN-5230-S VideoWall User’s Guide RS-232 Control ETX 06 PON RS-232 Commands RS-232 Control Items RCA 103 ERR WN-5230-S VideoWall User’s Guide 105 Specifications Optical Mechanical Environmental Picture Control Electrical BNC Regulatory Information Declaration of Conformity FCC Regulations Other Certifications Index ACK 113 VGA