Dell Command Line Interface 28

28 omreport: Viewing System Status Using theInstrumentation Service

Table 3-2. BIOS Setup Parameters

Parameters Description

Bezel Displays whether the bezel removal intrusion check during system

reboot is enabled or disabled.

Bootsequence Displays the device that is used to boot the system.

Console Redirection Displays if the BIOS screen is redirected over a particular serial port

or if it is turned off.

Console Redirection After Boot Displays whether console redirection after system reboot is enabled

or disabled.

Diskette Displays whether the diskette is disabled, auto enabled, or read only.

Demand Based Power

Management (DBS)

Displays whether DBS is enabled or disabled on the system.

Dual NIC Displays whether NIC 1 and NIC 2 with PXE is enabled or disabled.

External Serial Connector Displays whether the external serial connector is mapped to COM

port 1 or COM port 2 or a Remote Access Device.

Console Redirection Failsafe Baud

Rate

Displays the setting for console redirection failsafe baud rate.

IDE Displays whether the drive is enabled or disabled.

IDE Primary Drive 0 Displays whether the device is automatically detected and enabled

or if the device is disabled.

IDE Primary Drive 1 Displays whether the device is automatically detected and enabled

or if the device is disabled.

Intrusion Displays whether the intrusion check is enabled or disabled during

system boot.

Mouse Displays whether the mouse is enabled or disabled.

NIC 1 Displays whether the first NIC is enabled (with or without PXE) or

disabled during system boot.

NIC 2 Displays whether the second NIC is enabled (with or without PXE)

or disabled during system boot.

Numlock Displays whether the keypad can be used as number keys.

Parallel port address Displays whether the address is located on LPT1, LPT2, and LPT3,

or if it is disabled.

Parallel port mode Displays the setting associated with the parallel port.

Primary SCSI Displays whether the device is on or off.

RAID on motherboard Displays whether RAID-on-motherboard is detected as a RAID

device, a SCSI device, or if the device is disabled during system boot.

Contents

Main Notes and Notices Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2 omhelp: Getting Help With CLI Commands . . . . . . . . . . . . 19 Page Page Page Page 8 Using the Storage Management Service . . . . . . . . . . . . 135 Page Page Page Page Introduction What's New for Version 5.2 Using CLI Commands from Windows Command Prompts Primary CLI Commands CLI Error Checking and Error Messages Success Messages Failure Messages Scripting and Comparing With the CLI Command Syntax Overview mmddyy text yes | no mmddyy omhelp: Getting Help With CLI Commands Example Help Commands <command level 1 command level 2 command level 3> <name=value pair 1> [name=value pair 2] omreport: Viewing System Status Using the Instrumentation Service omreport Command Summary Page Page 24 Help With the omreport Command omreport about omreport chassis Commands omreport chassis omreport chassis acswitch omreport chassis batteries omreport chassis bios omreport chassis biossetup 28 omreport chassis bmc omreport chassis currents omreport chassis fans omreport chassis fancontrol omreport chassis firmware omreport chassis frontpanel omreport chassis fru omreport chassis info omreport chassis intrusion omreport chassis leds omreport chassis memory omreport chassis nics omreport chassis ports omreport chassis processors Page omreport chassis pwrsupplies omreport chassis remoteaccess omreport chassis slots omreport chassis temps omreport chassis volts omreport system Commands omreport system Commands for Viewing Logs omreport system alertaction omreport system assetinfo omreport system events Page omreport system operatingsystem omreport system pedestinations omreport system platformevents omreport system recovery omreport system shutdown omreport system summary Page Page Page omreport system thrmshutdown omreport system version Page Page omconfig: Managing Components Using the Instrumentation Service omconfig Command Summary 52 NOTE: Help With the omconfig Command omconfig about omconfig chassis omconfig chassis biossetup NOTE: Page NOTICE: 60 NOTE: omconfig chassis bmc 62 NOTE: 64 NOTE: Page Page Page 68 NOTE: omconfig chassis currents omconfig chassis fans omconfig chassis fancontrol omconfig chassis frontpanel omconfig chassis info omconfig chassis leds omconfig chassis memorymode omconfig chassis remoteaccess 76 NOTE: Page Page Page Page 82 NOTE: 84 omconfig chassis temps Table4-14 shows the valid parameters for setting temperature warning thresholds: Valid Parameters for Temperature Warning Thresholds omconfig chassis volts omconfig preferences omconfig preferences cdvformat omconfig preferences dirservice omconfig preferences snmp omconfig preferences useraccess omconfig system omconfig system alertaction 90 Available Alert Actions Table4-20 shows the alert actions for each component that allows you to configure an alert action Components and Events for Which You Can Set Alert Actions Page Commands for Clearing Logs omconfig system pedestinations omconfig system platformevents Page omconfig system events omconfig system webserver omconfig system recovery omconfig system shutdown omconfig system thrmshutdown Page Page omconfig system assetinfo: Editing Cost of Ownership Values omconfig System Asset Info Overview User Level Required for Adding Asset Information Adding Acquisition Information Example Commands for Adding Acquisition Information Adding Depreciation Information Example Commands for Adding Depreciation Information Adding Extended Warranty Information Example Command for Adding Extended Warranty Information Adding Lease Information Example Command for Adding Lease Information Adding Maintenance Information Example Command for Adding Maintenance Information Adding Outsource Information Example Command for Adding Outsource Information Adding Owner Information Example Command for Adding Owner Information Adding Service Contract Information Example Command for Adding Service Information Adding Support Information Example Command for Adding Support Information Adding System Information Example Command for Adding System Information Adding Warranty Information Example Command for Adding Warranty Information omreport rac: Viewing Remote Access Controller Components omreport rac Command Summary Help With the omreport rac Command omreport rac authentication Example Command for omreport rac authentication omreport rac dialinusers omreport rac dialoutusers Page omreport rac viewcertificate Page omconfig rac: Managing the Remote Access Controller omconfig rac Command Summary 120 Help With the omconfig rac Command omconfig rac authentication Local Operating System Authentication Example Command for omconfig rac authentication omconfig rac dialinusers omconfig rac dialoutusers omconfig rac generatecert omconfig rac modem 126 omconfig rac network omconfig rac snmptraps omconfig rac remote omconfig rac rmdialinuser omconfig rac rmdialoutuser omconfig rac rmsnmptrap omconfig rac rmuser omconfig rac reset omconfig rac uploadcert omconfig rac users Page Page Using the Storage Management Service CLI Command Syntax Syntax for Required, Optional, and Variable Command Elements User Privileges for omreport storage and omconfig storage omreport Command 138 omreport Storage Help The following table provides the omreport storage command syntax. omreport Controller Status omreport Global Information (Smart Thermal Shutdown Status) omreport Battery Status omreport Connector Status NOTE: omreport Enclosure Status omreport Temperature Probe Status omreport Fan Status NOTE: omreport Power Supply Status omreport EMM Status omreport Physical Disk Status omreport Virtual Disk Status omconfig Global Commands omconfig Global Enable Smart Thermal Shutdown omconfig Global Disable Smart Thermal Shutdown omconfig Global Rescan Controller omconfig Controller Commands omconfig Rescan Controller omconfig Global Rescan Controller omconfig Enable Controller Alarm omconfig Disable Controller Alarm omconfig Quiet Controller Alarm omconfig Test Controller Alarm omconfig Reset Controller Configuration omconfig Create Virtual Disk Page Page Page omconfig Set Controller Rebuild Rate omconfig Set Background Initialization Rate omconfig Set Reconstruct Rate omconfig Set Check Consistency Rate omconfig Export the Controller Log omconfig Import Foreign Configuration omconfig Import/Recover Foreign Configuration omconfig Clear Foreign Configuration omconfig Set Patrol Read Mode omconfig Start Patrol Read omconfig Stop Patrol Read omconfig Virtual Disk Commands omconfig Blink Virtual Disk omconfig Unblink Virtual Disk omconfig Initialize Virtual Disk omconfig Cancel Initialize Virtual Disk omconfig Fast Initialize Virtual Disk omconfig Slow Initialize Virtualize Disk omconfig Cancel Background Initialize omconfig Restore Dead Segments omconfig Split Mirror omconfig Unmirror omconfig Assign Dedicated Hot Spare omconfig Unassign Dedicated Hot Spare omconfig Check Consistency omconfig Cancel Check Consistency omconfig Pause Check Consistency omconfig Resume Check Consistency omconfig Delete Virtual Disk omconfig Format Virtual Disk omconfig Reconfiguring Virtual Disks omconfig Change Virtual Disk Policy omconfig Rename Virtual Disk omconfig Physical Disk Commands omconfig Blink Physical Disk omconfig Unblink Physical Disk omconfig Prepare to Remove Physical Disk omconfig Initialize Physical Disk omconfig Offline Physical Disk omconfig Offline Physical Disk omconfig Online Physical Disk omconfig Assign Global Hot Spare omconfig Unassign Global Hot Spare omconfig Rebuild Physical Disk omconfig Cancel Rebuild Physical Disk omconfig Remove Dead Segments omconfig Clear Physical Disk omconfig Cancel Clear Physical Disk omconfig Battery Commands omconfig Recondition Battery omconfig Start Battery Learn Cycle omconfig Delay Battery Learn Cycle omconfig Connector Commands omconfig Rescan Connector Example Syntax omconfig Enclosure Commands The following sections provide the omconfig command syntax required to execute enclosure tasks. omconfig Enable Enclosure Alarm omconfig Disable Enclosure Alarm omconfig Enable Smart Thermal Shutdown omconfig Disable Smart Thermal Shutdown omconfig Set Enclosure Asset Tag omconfig Set Enclosure Asset Name omconfig Set Temperature Probe Thresholds omconfig Reset Temperature Probe Thresholds omconfig Set All Temperature Probe Thresholds omconfig Reset All Temperature Probe Thresholds omconfig Blink Page Page Working With CLI Command Results Output Options for Command Results Controlling Command Output Display Writing Command Output to a File Page Selecting a Format for Your CLI Command Output Page Page Page Glossary Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Index Symbols A B C Page D E F G H I K O Page Page P R S T U V W