USA
II. INSTRUCTIONS FOR INSTALLATION
Important: The oven outer panels must be removed to perform the operations described in this chapter. Since the appliance must be switched on to make certain adjustments, exercise the utmost care when working in the vicinity of live electrical parts.
1.3 UNPACKAGING
•Remove the appliance from the packaging and take away the protective film that covers the appliance's external panels care- fully to avoid leaving any trace of glue. If necessary remove the glue using an a
•Dispose of packaging material in compliance with the regulations in force in the country where the product is to be used.
1. PLACE OF INSTALLATION
1.1 VENTILATION
The necessity for a properly designed and installed ventilation system cannot be over emphasized. The ventilation system will allow the unit to function properly while removing unwanted vapors and products of combustion from the operating area.
Theappliancemustbeventedwithaproperlydesignedmechanically driven exhaust hood. The hood should be sized to completely cover the equipment plus an overhang of a least 6"/15.3cm on all sides not adjacent to a wall. The capacity of the should be sized appropriately and provisions for adequate makeup air.
Refer to your local ventilation codes. In the absence of local codes, refer to the National ventilation code titled, “Standard for the Installation of Equipment for the Removal of Smoke and Grease Laden Vapors from Commercial Cooking Equipment”,
It is recommended that the ventilation system and duct work be checkedatprevailingintervalsasspecifiedbythehoodmanufactured
•The appliance mustonly be installed in adequately ventilated premises.
NOTICE: Proper ventilation is the owner's is responsibility. Any problem due to improper ventilation will not be covered by the warranty.
1.4IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
The container should be examined for damage before and during unloading. The freight carrier has assumed responsibility for its safe transit and delivery. If damaged equipment is received, either apparent or concealed, a claim must be made with the delivering carrier. Apparent damage or loss must be noted on the freight bill at the time of delivery. The freight bill must then be signed by the carrier representative (Driver). If the bill is not signed, the carrier may refuse the claim. The supply can supply the necessary forms. A request for inspection must be made to the carrier within 15 days if there is concealed damage or loss that is not apparent until after the equipment is uncrated. The carrier should arrange an inspection. Be certain to hold all contents plus all packing material. Under no circumstances should a damaged appliance be returned to the manufacturer without prior notice and written authorization.
2. POSITIONING
•Refer to the installation diagrams at the beginning of this booklet for the space requirements and connection dimensions of the appliance.
•Clearance of approximately 23.62" (50cm) must be left between the appliance’s left side panel and adjacent structures in order to provide space for maintenance operations when needed; the right side panel and the rear panel of the appliance must be at least 1.97" (5cm) from adjacent structures.
•Place the appliance in the required position and level the oven with a slight pitch toward the rear to help drain water from chamber using the appropriate bullet feet.
•The appliance is not suitable for
5958 931 01
1.2 REFERENCE STANDARDS
Note: The electric supply installation must satisfy the requirements of the appropriate statutory authority, such as the National Electrical Code (NEC) ANSI/NFPA70, (U.S.A..): the Canadian Electrical Code, CSA C22.2; or other applicable regulations.
Note: The electric supply connection must meet all national and local electrical code requirements.
Note: The installation of this unit must conform to local codes or, in the absence of local codes, to all National Codes governing plumbing, sanitation, safety and good trade practices, and to the National Gas Code ANSI Z223.1.
•Local codes regarding installation vary greatle from one area to another. This equipment is to be installed to comply with the applicable federal, state or local codes.
The installation instructions contained herein are for the use of qualified installation and service personnel only. Installation or service by other than qualified personnel may result in damage to the appliance and/or injury to the operator.
FAILURE TO COMPLY WITH INSTALLATION INSTRUCTION OR IMPROPER INSTALLATION WILL VOID WARRANTY AND RESPONSIBLITIES OF THE MANUFACTURE.
The National Fire Protection Association, Inc states in its NFPA 96 latest edition that local codes are the "authority having jurisdiction" when it comes to installation requirements for equipment. Therefore, installations should comply with all local codes.
Warning: The oven must be installed on an even (level) non- flammable flooring and any adjacent walls must be
Important:
Make sure steam from the oven’s drain or adjacent
appliances does not enter the aeration vents under the
appliance, designed to cool internal components
located at the bottom of the appliance.
3. ELECTRICAL CONNECTION
•A fused disconnect switch or main circuit breaker (customer furnished) MUST be installed in the electric supply line for the appliance. It is recommended that this switch/circuit breaker have lockout/tagout capability. Before making any electrical connections to this appliance, check that the power supply is adequate for the voltage, amperage, and phase requirements on the rating plate.
•A safety cutout switch of suitable capacity with a contact breaking distance of at least 3 mm must be fitted upstream of the appliance.
The cutout switch must be installed near the appliance in the permanent electrical system of the premises.
•The appliance must be electrically grounded in accordance
13
