Mode Switch item 6, Figure | GE Monogram GFK-1115 instruction

2

Genius Bus Connector, Isolated (item 4, Figure 2-2)

a45318

SHLD OUT

SHLD IN

X2

X1

Pin	Description
SHLD OUT	Shield Out (to next physical
	device on bus)
SHLD IN	Shield In (from previous
	physical device on bus)
X2	Serial 2
X1	Serial 1

Mode Switch (item 6, Figure 2-2)

The mode of operation for the Panel Controller is selected by setting the Operating Mode switch (see Table 2-2 for operating modes).

Device Number Switches (item 8,

Figure 2-2)

The Genius bus address for the C400 Controller is set using the Device Number switches. Valid device numbers are 00 to 31, inclusive.

Lithium Battery (item 7, Figure 2-2)

The lithium battery is stored in its own compartment in the Controller and covered for its own and the user's protection. It should be replaced every two years, or whenever the software indicates that the battery is low.

Warning

Lithium batteries are considered harmful waste. Dispose of them in accordance with the instructions in the Material Safety Data Sheet (MSDS) that accompany the battery, and in accordance with local regulations.

GFK-1115

Chapter 2 C400 Panel Controller Hardware

2 - 7

Image 21

GE Monogram GFK-1115 manual Genius Bus Connector, Isolated item 4, Figure, Mode Switch item 6, Figure

Contents

GE Fanuc Automation Cimplicity Preface Content of This Manual Related Publications PrefacePanelware Manuals Other Documents We Welcome Your Comments and Suggestions Contents Contents Creating the Demo Project Description of the Demo Project Appendix a Cabling Information Overview PCS Project Component Descriptions Panelware Configuration SoftwareProject Component Definition Hardware and Software Requirements DescriptionCatalog Number PLC Requirements Document Conventions Key SymbolsMenu Functions Key C400 Panel Controller Hardware Connecting Power to the Controller Power RequirementSetting Number Switches General Information Specifications Technical DataGenius Panel Controller C400 Page Genius Panel Controller C400 Elements/Connections Overview of Connections and Operational Elements Pin Description IF0 RS-232, Non-isolated item 3, FigurePin D-Type M Meaning Mode Switch item 6, Figure Genius Bus Connector, Isolated item 4, FigureDevice Number Switches item Lithium Battery item 7, Figure Reset Button item 9, Figure C400 Controller Mode Switch Settings Reset ModesOperating the C400 Controller FlashPROM Loading and Starting Panel Programs Update Mode/Reloading the Operating SystemLoading the Panel Program Starting the Panel Program Quick Start Software Installation Calling the Setup ProgramLanguage Selection Installation Menu Start InstallationChanging the Destination Path Exiting the Installation Screen Configuration Starting PCS General Operation Pull-Down Menus Main MenuWindow Name Context-Sensitive Help Screens Selection Windows Basic PCS Screen Elements Screen Elements PCS Configuration Creating a New Project GFK-1115 Quick Start List Entry Keyblock Module Keyblock Module Definitions GFK-1115 Quick Start Defining Connections Connection to a GE Fanuc PLC via Genius Page GFK-1115 Quick Start Internal Connection Genius Internal Connection Key Assignments Abbr Keyblock Abbreviation Definitions Picture Creating Pictures GFK-1115 Quick Start Places after dec. point TagnameVALUE1 Places after dec. point TagnameVALUE1 Picture GFK-1115 Quick Start Picture Defining the Project Variables Genius Device Connection Genius Internal Connection Internal Connection Binding Pictures in the Project Picture for a Communications Error Picture Binding Overview Error Picture Start-up Picture Pict1 Picture List Organization Compiling the Project Panel/PC Serial Connection Downloading the Project to the PanelPage PLC/Panel Connection Connecting the PLC and the Panel Starting the Project Exiting PCS Configuring Communication with the PLC Genius Protocol Parameters Definition in PCS PLC Types PLC Type Summary of PLC Data TypesInterface Memory Types Supported PLC Node Parameter Definitions Target device numberTaskname PV-Name internal Error Number Write priorityNumber of retries PLC Network Parameter Definitions Baud RateBroadcast control data length Timeout 10 ms Command timer 10 msData interface service Blocking distance SNP 90 Protocol Parameters Definition in PCS Global data starting referenceC400 Bus Address Global Data Starting Reference Settings on the Panel Configuration of the PLC InterfacePanel Interface Module Interface Panel to PLC Interface Connections for Genius Protocol PCS Connection Editor Accessing the Connection List Using Function Keys in the Connection List Elements of the Connection ListOverview Editing/Inserting Connections Defining/Changing an IDDefining/Changing a Connection Editing PLC Node Parameters of a Connection Deleting Connections Editing the Variable Assignment Table Elements of the VATAssignment Table F10 Exit Function Keys of the VAT Editing/Inserting Variable Assignments Entering/Changing the TagnameEntering/Changing PLC Addresses Entering/Changing PLC Variable Types Allowable PLC Address Data TypesPLC Variable Type Panel Data Type PDT Marking Unused Variables Deleting Variable AssignmentsAddress Code Groups Series 90-30/Series Global Data Format Data Type Conversions Variable Data TypesFormat in the PCS Panel Data Type PLC Data Type Value Range Data Type Conversion Data Type Conversions Panel Data Type/PLC Word INT Dint Dword Float String BIT Possible Data Type Conversions for Series Long u Long s Float String Possible Data Type Conversions for Series Five/Series Six Demo Project Project Name Directory General Information Required Hardware Defining the User Path Downloading the Demo Project Loading the Project Downloading and Starting the Project PanelPCS Description of the Demo Project KeysKey LEDs Main Menu Input Values Picture Value Entries Clock Picture Input Password Picture Entering a Password Locked Input Picture F1 Switches back to the Input Password picture Key Functions Alarm time When the alarm occurred Alarm number Alarm List Error Picture Creating a Project Creating the Demo Project Preparing a Concept Creating a New Project Selecting the Connections Page GFK-1115 Demo Project Defining Key Assignments Creating the Pictures Main Picture Main Menu GFK-1115 Demo Project Page GFK-1115 Demo Project Input Picture Value Entries Press F2 Field Press F2 Field Press F2 Field Press F2 Field Press Esc or F10 Exit Clock Picture Setting the Real Time ClockVariable name Data type Press F2 Field GFK-1115 Demo Project Field or Scaling parameters Field No See figure on GFK-1115 Demo Project Page Press Esc or F10 Exit Password Picture Password Entry Output Bit/Byte Complete Inplock Picture password protected entry of values INPUT#1 INPUT#2 Keyfunct Picture Key Functions Completion Setword Tagname Alarm Picture Alarm List GFK-1115 Demo Project ERRNR/DI Errpic Picture Error Picture Defining the Text Groups Binding Pictures to the Project Binding the Main Picture Binding Process Pictures Binding the Remaining Pictures Clock Picture Inplock Picture Errpic Picture Picture Directory/Startup Picture GFK-1115 Demo Project Press F2 Ins. The Alarm Group Definition window appears Editing the Alarm System Bit No Alarm Number Alarm Text Activating the Alarm System Internal Connection Editing the Connections Genius Internal Connection Symbolic Name Panel Data Type PLC Address PLC Variable Type Genius GBC Series 90-70 ConnectionGenius GBC Series 90-70 connection Compiling the Project Errors Cabling Information Using Other Cable Types Genius CommunicationsSelecting a Cable Type Table a 1. Recommended Cable Types Bus Length and Baud Rate for Busses with Phase a Devices Bus LengthBaud Rate Selection SNP Communications Connecting Devices to the Bus Cable Diagrams Table a 2. Cable Diagrams for Various ConfigurationsTable a 3. Pin-out Diagram Locations in Documentation Errors/Troubleshooting Errors During Installation PCS cannot be started Errors During Program Start Faults running PCS Errors While Working in PCS Error! Error picture and first picture cannot be the same Error Number Definition Error Numbers in Internal User Variable Index IF1 RS-232 PCS