Manuals / Kodak / Computer Equipment / Scanner

Kodak A-61092 manual Before you begin, Positioning the Patch Reader

Models: A-61092

1 118

Download 118 pages 34.53 Kb

Page 105

Before you begin

Before you begin

Before feeding documents containing patches, verify the following:

∙The Patch Reader is properly positioned.

∙Patch reading is enabled.

∙End-fed patch reading is enabled (if desired).

∙The patch code confirmation tone is enabled (if desired).

Positioning the Patch Reader

There are five locations for the Patch Reader.

NOTE: If patch reading is performed by a Document Scanning Array, the following instructions do not apply.

Using the Patch Reader The Patch Reader may be installed to read patches placed on the front of the documents being processed.

Patch Reader

Patch Reader

locations

To move the Patch Reader:

1.Lift the Patch Reader out of the current location and place it in the desired location.

2.Be sure the patch placed on the document and the position of the Patch Reader are aligned so the patch will be read properly.

A-61092 September 1999

8-39

Image 105

Kodak A-61092 manual Before you begin, Positioning the Patch Reader

Contents

User’s Guide Document ScannerA-61092 Part No. 1E8133 power before installation CAUTION Hot surface, avoid contact IMPORTANT Equipment shall be installed by qualified personnelWARNING Dangerous voltage. Disconnect the main ATTENTION Eviter le contact, pieces brulantespower before installation CAUTION Moving parts, avoid contact IMPORTANT Equipment shall be installed by qualified personnelWARNING Dangerous voltage. Disconnect the main ATTENTION Eviter le contact, pieces en mouvement1 Introduction Scanner featuresScanner options Feed tray - holds documents prior to feeding Rear view Mode name/number Scan modeindicator indicatorOperating keys and indicators Key/IndicatorFunction Operating keys and indicators Keys/IndicatorsKeys/Indicators FunctionKey/Indicator Operating keys and indicatorsClear/Cancel Run NEXT Stop Enter Function2 Getting Started Turning on the scannerSelecting the language display Calibrating the scanner Unsuccessful calibration Preparing documents for scanninggap semi-automatic feeder only Adjusting the feed and separator roller6. Turn the gap adjustment knob counterclockwise 2 1/2 turns automatic feeder only Adjusting the feed shelf position semiAdjusting the feed shelf side guides semi-automatic feeder onlyFeed Shelf Label Adjusting the exit hopper side guides and end stop arrowsside guides Changing the deflector Overview 3 Operating the ScannerSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder adjustment Feeding thick documentsGraphic depicts movement lever is usedFeeding documents using the automatic feeder 4 Function Codes Using function codesFunction code summary SetupStatus CountersOperation FootswitchScanning EndorserPatch Reader Super12 Document PrinterCode Function Code NameDescription F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 F39 CodeFunction Code Name DescriptionCode Function Code NameDescription Code EnterFunction Code Name DescriptionCode Function Code NameDescription Code Function Code NameDescription Cleaning tasks Cleaning materials Replacement parts 5 MaintenanceCleaning the imaging guides Daily maintenance procedures4. Remove dust from the imaging guides, using a soft bristle brush Cleaning the feed and separator rollers semi- automatic feeder Cleaning the feeder module and separator roller Cleaning the feeder module and separator roller automatic feederCleaning the separator roller Cleaning the paper path Vacuuming inside the scanner 1. Open the front cover 2. Raise the horizontal plate 7. Replace the imaging guides Weekly maintenance procedures Cleaning the exposure lamp housingsCleaning the cabinet Cleaning the air filter Monthly maintenance proceduresReplacing the air filter Replacement proceduresReplacing the exposure lamps 6. Dispose of or recycle the used lamps Replacing the imaging guides Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials 6 Operator Messages Operator Message Displayed Operator message listingDescription/Action Required CodeE121 E122 E123 E124 E125 E126 E127 E128 E130 E131 E132 E133 E140 E141 CodeOperator Message Displayed Description/Action RequiredCode Operator Message DisplayedDescription/Action Required Code Operator Message DisplayedDescription/Action Required Code Operator Message DisplayedDescription/Action Required E500 E501 E502 E503 E512 E513 E550 E551 E552 E553 E562 E563 E504 E505 CodeOperator Message Displayed Description/Action RequiredCode various messages various messages various messages various messagesOperator Message Displayed Description/Action RequiredTrouble and remedy chart 7 TroubleshootingTrouble Probable CauseTrouble Probable CauseRemedy The document path Clearing the document pathClearing documents The feeder/horizontal transport area Upper lamp housing assembly Upper imaging guide Lower imaging guide The imaging guide areaVertical baffle handle Baffle plate Lower roller assembly The lower roller assembly areaTop cover Baffle plate Upper turn handle The vertical transport area The upper turn areaExit handle Exit baffle Static brush Static brush under housing The document exit area8 Accessories Supply SuppliesCatalog # Imaging Station LampsPart/Tool Parts and toolsUnited States and Canada Order NumberUsing the Bar Code Reader Code Type Bar code typesCharacter Set Available Characters in SetBar code placement Before you begin Enabling the bar code confirma- tion tone Enabling bar code readingPerforming a bar code test 1. Perform test option 3=%KODAK Static bar code evaluation Using the Evaluate option1. Select 1=EVALUATE 2. Select either 1=Transport Off or 2=Transport OnRight-side access door Using the Imaging Station8-12 A-61092 September5. Tape the bar code sample section in place Dynamic bar code evaluation Evaluating test results Dimensional Fields Pass or FailGrade Reflectance Fields Grades A through FField A PassTable 2 - Common Causes of Low Bar Code Ratings Problem TypeCause FieldUsing the %KODAK option Using the Display option1. Select 2=DISPLAY ∙ Bar code was not readUsing the %NORM option The first time the test is run, the two percentages will be the same Using the check feeder Using the Check Feeder / Check StackerClearing jams in the check feeder Cleaning the check feeder Using the check stacker Die styles Using the EndorserTop cover Before you begin Changing the die drum2. Push down the locking lever 9. Raise the drum locking lever to secure the die drum assembly Changing the ink roller Setting the date and code number Enabling the Endorser Changing the print position Selecting the Endorser modeFootswitch Using the FootswitchEnabling the confirmation tone Footswitch Pressed actions Footswitch PressedAction Footswitch Pressed Definition Footswitch Released actionsFootswitch Released ActionPatch types Using the Patch ReaderPatch code placement Positioning the Patch Reader Before you beginCleaning the Patch Reader Enabling patch reading Enabling the patch code confirmation toneSensor Appendix A Basic Concepts ModesLinked modes Image addresses Using the Next key Assigning an image address∙ Enter Using Function Code F92 Image address formats Indexing schemesSingle level indexing Page Two level indexingeach document is defined as follows Page… Three level indexingThree level offset indexing Controlling document level changes EASTMAN KODAK COMPANY Document Imaging Rochester, New York DOCUMENT I M A G I N GA-61092 9/99 Eastman Kodak Company Printed in U.S.A Printed on recycled paper